Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Sagem
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

What S2000 is

S2000 is Sagem's sequential petrol controller, used by Renault and by Citroën. The name covers more than one installation. A 1999 Citroën description still has a cable throttle and calculates fuel from manifold pressure and engine speed. The Renault Laguna workshop text describes a 112-track S2000 with a motorised throttle. Citroën's January 2003 bulletin calls the motorised-throttle TU and EW system S2000 PM1 and gives it a torque calculation. Read the bulletin for the engine. The family index is Sagem. The earlier semi-sequential Renault unit is Safir. The later 128-track Renault unit is S3000.

Processor

The AutoTuner ECU compatibility list (tool compatibility listing, export date 28 October 2026) gives the S2000 microcontroller as a Siemens/Infineon C167-family part, listed as "C167" without a more specific device or flash part. This is a tool-vendor listing, not manufacturer documentation, and it does not distinguish the 1999 manifold-pressure unit from the PM1 or Laguna variants.

Citroën, November 1999

Citroën aftersales bulletin BRE 0636, November 1999, describes S2000 petrol injection as sequential, with a mapped injector time, integral electronic ignition and mapped advance. Load is the pressure in the intake manifold. A camshaft-position sensor is part of that system, and the bulletin also covers a secondary-air injection pump and valve.

The crankshaft sensor is inductive, facing the flywheel teeth. The bulletin uses 58 teeth to determine engine speed and the two missing teeth to determine crankshaft position. The air gap is not adjustable. The ECU selects coil pairs 1 with 4, and 3 with 2, from that speed signal. Ignition is wasted spark: one plug fires at the end of compression and the paired plug fires on the exhaust stroke. The coil drivers are inside the computer. There is no external ignition module. Synchronisation uses the cylinder-1 reference sensor. The flat-seat plugs in that bulletin are tightened to 2.5 m·daN, and the bulletin says the plug specification still follows the engine.

Idle air bypasses the throttle through a stepper. The bulletin gives that stepper four jobs: extra air when cold, hot-idle control under engine load, extra air for parking manoeuvres, and the transient correction. A resistor heats the throttle body. The throttle potentiometer marks closed throttle and full throttle, and it is an input to acceleration, deceleration and the fuel cut. On the automatic-gearbox version the injection computer also sends throttle position to the gearbox computer as the load signal. On the sensor connector in that bulletin, pin 1 is the 5 V supply, pin 2 is the signal and pin 3 is the shield, according to version.

A double relay, commanded by the computer, keeps a permanent 12 V supply for the computer memory with the ignition off. With the ignition on it feeds the computer and runs the fuel pump for 2 to 3 seconds, then stops the pump if the engine has not started. With the engine running it feeds the computer, the pump, the injectors, the coil, the canister-purge valve and the oxygen-sensor heaters.

S2000 PM1, Citroën TU and EW, January 2003

Bulletin BRE 1094, January 2003, is S2000 PM1 for the TU and EW petrol engines, and it specifies a motorised throttle. The computer calculates the torque the engine is being asked for from the accelerator-pedal sensor, then corrects that request for loads such as the alternator and the air-conditioning compressor. It delivers the torque by the throttle angle, by ignition advance under knock control, and by injection time.

Injection is sequential, in the order 1-3-4-2, just before the inlet stroke. The bulletin allows both a wasted-spark compact coil pack and a static system with a coil for each cylinder, so the coil arrangement is an installation difference, not a single PM1 standard. Manifold pressure is still measured. Some engines combine that pressure sensor with the air-temperature sensor. The idle stepper of the 1999 system is gone: idle air is the motorised throttle. The bulletin also covers exhaust-gas recirculation, canister purge, secondary air, and cooling-fan control, including an after-run and a degraded mode. It is an EOBD system.

Renault Laguna

The Laguna multipoint particulars describe a 112-track Sagem S2000 controlling injection and ignition. Injection is sequential, and this installation has no cylinder-1 sensor on the camshaft. Phasing is done in software from the top-dead-centre sensor. The injection warning lamp works, and a separate OBD lamp is fitted because the car has on-board diagnostics. The fuel circuit has no return to the tank. The pressure regulator is on the pump and gauge assembly.

Nominal idle is 750 rpm, including with the automatic transmission operating. Idle is corrected for air conditioning, the power-steering pressure switch, battery voltage and the heated windscreen. The computer drives the cooling fan and the coolant-temperature warning lamp. It also drives the air-conditioning compressor clutch. Canister purge is a duty cycle based on engine speed and manifold pressure. Two oxygen sensors are used, one upstream of the catalyst and one downstream. A camshaft dephaser, driven by a solenoid, is fitted on the F4P only. The throttle is motorised and regulates both airflow and idle speed. Cruise control and the speed limiter, and the air conditioning, are configured automatically.

The rev limiter in that text depends on the engine and on whether the coolant is still cold. Below 75 °C on the F4P, or below 60 °C on the K4M, and for no more than 10 seconds, the cut is 5800 rpm. Once hot, the cut is 6500 rpm on the K4M and 6300 rpm on the F4P, in the gears that text lists. Those figures belong to this Laguna S2000 description. They are not the Mégane S3000 limits, and they are not a Safir limit.

Replacing the computer on this Laguna has a procedure because the immobiliser is the third-generation coded type. The ECU from another car will not authorise a start until that procedure has been carried out with Renault equipment. The same page describes the Laguna V6 as a Bosch ME7.4.6, 128 tracks, with pencil coils and four oxygen sensors. That V6 is not an S2000.

Not established

The exact C167 device, the flash part, and a published connector pinout for the S2000 are not established.

Sources

  • Automobiles Citroën, BRE 0636 F, November 1999, Principe de fonctionnement: injection Sagem S2000. The cable-throttle, manifold-pressure system, the 58-tooth crank target, the coil pairs and the double relay.
  • Automobiles Citroën, BRE 1094 F, January 2003, Injection Sagem S2000 PM1, TU and EW engines with a motorised throttle. The torque calculation and the sequential order.
  • Renault Laguna workshop particulars for multipoint Sagem S2000, as republished at Laguna Notice. The 112-track computer, idle, rev limits and the motorised throttle. Accessed 2026-11-13.
  • AutoTuner ECU compatibility list (PDF), export date 28 October 2026, tool vendor. Microcontroller family for Sagem S2000. Accessed 19 November 2026.