Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Bosch ME9.2
Applies to
Bosch ME9.2
Tool groups
None
Manufacturers
BMW, Bosch

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Scope

The BMW N62 V8 engine control unit (see Bosch ME9.2) is connected through five modular connectors, X60001 to X60005, of 9, 24, 52, 40 and 9 pins (134 in total). BMW's technical information system (TIS) publishes the pin assignments for the N62TU control unit, issue status 12/2007. This is manufacturer service documentation. The sheet does not itself name the Bosch designation, so its application to the ME9.2 control unit rests on the matching 9/24/52/40/9 connector layout; it should be checked against the wiring diagram for the individual vehicle.

Reading the tables

The diagrams are pin-index drawings: the source gives pin numbers and functions but not the connector face layout or viewing orientation. Pins that the source lists without a function are shown with an empty function. Entries limited to certain model lines (E60, E61, E63, E64, E70) or to the US version are noted against the pin. The source states that current pin assignments should be checked in BMW's diagnosis system. Pin 9 of X60005 is not legible in the extract used and is left blank.

Connector functions in outline

X60001 (9-pin): power supply (terminals 30 and 87), earth and the engine-speed signal to the transmission control.X60002 (24-pin): oxygen sensor signals and heater outputs for both banks.X60003 (52-pin): injectors, VANOS solenoids, camshaft, crankshaft, knock and coolant sensors, air-mass and manifold-pressure sensors, throttle actuator, mapped thermostat and the local CAN link to the Valvetronic control unit.X60004 (40-pin): accelerator pedal module, PT-CAN, brake, clutch and oil-pressure switch inputs, fuel-pump relay, electric fan and electronics-box fan, and the CAS links.X60005 (9-pin): ignition coil outputs for cylinders 1 to 8 and ignition earth.

Diagram redrawn by Tuning Wiki from the BMW TIS sheet.

Sources

BMW TIS, "DME control unit: N62TU", BMW AG technical information system sheet, issue status 12/2007, printed 23 December 2015, hosted on an independent E64 owner site. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bosch ME9.2 (BMW N62) connector pinout

Scope

The BMW N62 V8 engine control unit (see Bosch ME9.2) is connected through five modular connectors, X60001 to X60005, of 9, 24, 52, 40 and 9 pins (134 in total). BMW's technical information system (TIS) publishes the pin assignments for the N62TU control unit, issue status 12/2007. This is manufacturer service documentation. The sheet does not itself name the Bosch designation, so its application to the ME9.2 control unit rests on the matching 9/24/52/40/9 connector layout; it should be checked against the wiring diagram for the individual vehicle.

Reading the tables

The diagrams are pin-index drawings: the source gives pin numbers and functions but not the connector face layout or viewing orientation. Pins that the source lists without a function are shown with an empty function. Entries limited to certain model lines (E60, E61, E63, E64, E70) or to the US version are noted against the pin. The source states that current pin assignments should be checked in BMW's diagnosis system. Pin 9 of X60005 is not legible in the extract used and is left blank.

Connector functions in outline

  • X60001 (9-pin): power supply (terminals 30 and 87), earth and the engine-speed signal to the transmission control.
  • X60002 (24-pin): oxygen sensor signals and heater outputs for both banks.
  • X60003 (52-pin): injectors, VANOS solenoids, camshaft, crankshaft, knock and coolant sensors, air-mass and manifold-pressure sensors, throttle actuator, mapped thermostat and the local CAN link to the Valvetronic control unit.
  • X60004 (40-pin): accelerator pedal module, PT-CAN, brake, clutch and oil-pressure switch inputs, fuel-pump relay, electric fan and electronics-box fan, and the CAS links.
  • X60005 (9-pin): ignition coil outputs for cylinders 1 to 8 and ignition earth.

Diagram redrawn by Tuning Wiki from the BMW TIS sheet.

Sources

  • BMW TIS, "DME control unit: N62TU", BMW AG technical information system sheet, issue status 12/2007, printed 23 December 2015, hosted on an independent E64 owner site. Accessed 19 November 2026.

Connector pinout

Applicability

BMW TIS sheet "DME control unit: N62TU" (issue status 12/2007), five connectors X60001-X60005 of 9, 24, 52, 40 and 9 pins. OEM service documentation; the sheet does not name the Bosch designation, so applicability to the ME9.2 N62 control unit is inferred from the matching connector layout. Some functions apply to specific model lines (E70, US version) as noted.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

Connector X60001 (9-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60001 (9-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60001 (9-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Engine speed signal to electronic transmission control fed though integrated supply module (TxD wire)
Cavity: Populated
Confirmed

BMW TIS

not E70
Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Terminal 30 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

E70: terminal 30 from front power distributor in the junction box
Terminal 87 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

E70: terminal 87 from front power distributor in the junction box
Terminal 30 for switching the DME main relay
Cavity: Populated
Confirmed

BMW TIS

E70 only

Connector X60002 (24-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60002 (24-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60002 (24-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Oxygen sensor heating for oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Oxygen sensor heating for oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Oxygen sensor heating for oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Oxygen sensor heating for oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Signal from oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Terminal 85 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

not E70
Unknown function
Cavity: Unknown
Unknown

Connector X60003 (52-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60003 (52-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60003 (52-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
Signal from inlet pipe pressure sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from intake air temperature sensor in hot-film air-mass sensor
Cavity: Populated
Confirmed

BMW TIS

Power supply for intake pipe pressure sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from hot-film air-mass sensor
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 4
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 5
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 6
Cavity: Populated
Confirmed

BMW TIS

Actuation of VANOS solenoid valve 2 - inlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of VANOS solenoid valve - inlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 7
Cavity: Populated
Confirmed

BMW TIS

Actuation of mapped thermostat
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 1
Cavity: Populated
Confirmed

BMW TIS

Earth wire to hot-film air mass meter, intake manifold pressure sensor and coolant temperature sensor
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from exhaust camshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from exhaust camshaft sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal wire to Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Bitserial data interface to alternator and oil condition sensor
Cavity: Populated
Confirmed

BMW TIS

E60, E61, E63, E64 and E70: also the intelligent battery sensor
Actuation of VANOS solenoid valve - exhaust
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel evaporation control valve
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Actuation of VANOS solenoid valve 2 - exhaust
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 8
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 3
Cavity: Populated
Confirmed

BMW TIS

Signal from crankshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from coolant-temperature sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from inlet camshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from inlet camshaft sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal from throttle-valve actuator (potentiometer 1)
Cavity: Populated
Confirmed

BMW TIS

Signal from throttle-valve actuator (potentiometer 2)
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 3
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 4
Cavity: Populated
Confirmed

BMW TIS

Earth wire to crankshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Local CAN (High) between DME control unit and Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Actuation of DISA servomotor and DISA servomotor 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of DISA servomotor and DISA servomotor 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Actuation of throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Reference voltage to air-mass flow sensor
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from knock sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 3
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 4
Cavity: Populated
Confirmed

BMW TIS

Power supply to throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Local CAN (Low) between DME control unit and Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Earth wire to throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Connector X60004 (40-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60004 (40-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60004 (40-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
US version: Signal for heating to diagnosis module for tank leakage
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal to electric fan
Cavity: Populated
Confirmed

BMW TIS

Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Terminal 50E from CAS control unit
Cavity: Populated
Confirmed

BMW TIS

not E70
Earth wire to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Signal from accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Power supply to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel-pump relay
Cavity: Populated
Confirmed

BMW TIS

E60, E61, E63, E64 and E70
Unknown function
Cavity: Unknown
Unknown
Earth wire to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Signal from accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Power supply to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Engine-speed signal to diagnosis socket
Cavity: Populated
Confirmed

BMW TIS

not E70
Actuation of exhaust flap
Cavity: Populated
Confirmed

BMW TIS

not E70
Actuation of electronics box fan
Cavity: Populated
Confirmed

BMW TIS

US version: Actuation of leakage diagnosis pump
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Engine-speed signal from DSC control unit
Cavity: Populated
Confirmed

BMW TIS

Signal from clutch module
Cavity: Populated
Confirmed

BMW TIS

Signal from brake light switch
Cavity: Populated
Confirmed

BMW TIS

Signal from oil pressure switch via integrated supply module
Cavity: Populated
Confirmed

BMW TIS

E70: signal from oil pressure switch
Terminal 15 wake-up wire
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from brake light test switch
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
US version: Signal from leakage diagnosis pump
Cavity: Populated
Confirmed

BMW TIS

Signal for active air flap control (introduction from 03/2007 on E60, E61)
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
EWS signal to CAS control unit
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
PT-CAN High
Cavity: Populated
Confirmed

BMW TIS

PT-CAN Low
Cavity: Populated
Confirmed

BMW TIS

Earth wire to temperature sensor at radiator outlet
Cavity: Populated
Confirmed

BMW TIS

Signal from temperature sensor on radiator outlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of starter inhibitor relay in integrated supply module
Cavity: Populated
Confirmed

BMW TIS

E70: engine start signal from CAS

Connector X60005 (9-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60005 (9-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60005 (9-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Actuation of no. 3 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 4 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 1 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 7 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Ignition earth
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 8 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 2 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 6 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Revision 1: Bosch ME9.2 (BMW N62) connector pinout

Scope

The BMW N62 V8 engine control unit (see Bosch ME9.2) is connected through five modular connectors, X60001 to X60005, of 9, 24, 52, 40 and 9 pins (134 in total). BMW's technical information system (TIS) publishes the pin assignments for the N62TU control unit, issue status 12/2007. This is manufacturer service documentation. The sheet does not itself name the Bosch designation, so its application to the ME9.2 control unit rests on the matching 9/24/52/40/9 connector layout; it should be checked against the wiring diagram for the individual vehicle.

Reading the tables

The diagrams are pin-index drawings: the source gives pin numbers and functions but not the connector face layout or viewing orientation. Pins that the source lists without a function are shown with an empty function. Entries limited to certain model lines (E60, E61, E63, E64, E70) or to the US version are noted against the pin. The source states that current pin assignments should be checked in BMW's diagnosis system. Pin 9 of X60005 is not legible in the extract used and is left blank.

Connector functions in outline

  • X60001 (9-pin): power supply (terminals 30 and 87), earth and the engine-speed signal to the transmission control.
  • X60002 (24-pin): oxygen sensor signals and heater outputs for both banks.
  • X60003 (52-pin): injectors, VANOS solenoids, camshaft, crankshaft, knock and coolant sensors, air-mass and manifold-pressure sensors, throttle actuator, mapped thermostat and the local CAN link to the Valvetronic control unit.
  • X60004 (40-pin): accelerator pedal module, PT-CAN, brake, clutch and oil-pressure switch inputs, fuel-pump relay, electric fan and electronics-box fan, and the CAS links.
  • X60005 (9-pin): ignition coil outputs for cylinders 1 to 8 and ignition earth.

Diagram redrawn by Tuning Wiki from the BMW TIS sheet.

Sources

  • BMW TIS, "DME control unit: N62TU", BMW AG technical information system sheet, issue status 12/2007, printed 23 December 2015, hosted on an independent E64 owner site. Accessed 19 November 2026.

Connector pinout

Applicability

BMW TIS sheet "DME control unit: N62TU" (issue status 12/2007), five connectors X60001-X60005 of 9, 24, 52, 40 and 9 pins. OEM service documentation; the sheet does not name the Bosch designation, so applicability to the ME9.2 N62 control unit is inferred from the matching connector layout. Some functions apply to specific model lines (E70, US version) as noted.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

Connector X60001 (9-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60001 (9-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60001 (9-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Engine speed signal to electronic transmission control fed though integrated supply module (TxD wire)
Cavity: Populated
Confirmed

BMW TIS

not E70
Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Terminal 30 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

E70: terminal 30 from front power distributor in the junction box
Terminal 87 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

E70: terminal 87 from front power distributor in the junction box
Terminal 30 for switching the DME main relay
Cavity: Populated
Confirmed

BMW TIS

E70 only

Connector X60002 (24-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60002 (24-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60002 (24-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Oxygen sensor heating for oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Oxygen sensor heating for oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Oxygen sensor heating for oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Oxygen sensor heating for oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal to oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor downstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Signal from oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Signal from oxygen sensor 2 upstream of catalytic converter
Cavity: Populated
Confirmed

BMW TIS

Terminal 85 from integrated supply module, power supply
Cavity: Populated
Confirmed

BMW TIS

not E70
Unknown function
Cavity: Unknown
Unknown

Connector X60003 (52-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60003 (52-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60003 (52-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
Signal from inlet pipe pressure sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from intake air temperature sensor in hot-film air-mass sensor
Cavity: Populated
Confirmed

BMW TIS

Power supply for intake pipe pressure sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from hot-film air-mass sensor
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 4
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 5
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 6
Cavity: Populated
Confirmed

BMW TIS

Actuation of VANOS solenoid valve 2 - inlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of VANOS solenoid valve - inlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 7
Cavity: Populated
Confirmed

BMW TIS

Actuation of mapped thermostat
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 1
Cavity: Populated
Confirmed

BMW TIS

Earth wire to hot-film air mass meter, intake manifold pressure sensor and coolant temperature sensor
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from exhaust camshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from exhaust camshaft sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal wire to Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Bitserial data interface to alternator and oil condition sensor
Cavity: Populated
Confirmed

BMW TIS

E60, E61, E63, E64 and E70: also the intelligent battery sensor
Actuation of VANOS solenoid valve - exhaust
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel evaporation control valve
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Actuation of VANOS solenoid valve 2 - exhaust
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 8
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel injector for cylinder 3
Cavity: Populated
Confirmed

BMW TIS

Signal from crankshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from coolant-temperature sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from inlet camshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from inlet camshaft sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal from throttle-valve actuator (potentiometer 1)
Cavity: Populated
Confirmed

BMW TIS

Signal from throttle-valve actuator (potentiometer 2)
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 3
Cavity: Populated
Confirmed

BMW TIS

Signal to knock sensor 4
Cavity: Populated
Confirmed

BMW TIS

Earth wire to crankshaft sensor
Cavity: Populated
Confirmed

BMW TIS

Local CAN (High) between DME control unit and Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Actuation of DISA servomotor and DISA servomotor 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of DISA servomotor and DISA servomotor 2
Cavity: Populated
Confirmed

BMW TIS

Actuation of throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Actuation of throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Reference voltage to air-mass flow sensor
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from knock sensor
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 2
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 3
Cavity: Populated
Confirmed

BMW TIS

Signal from knock sensor 4
Cavity: Populated
Confirmed

BMW TIS

Power supply to throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Local CAN (Low) between DME control unit and Valvetronic control unit
Cavity: Populated
Confirmed

BMW TIS

Earth wire to throttle-valve actuator
Cavity: Populated
Confirmed

BMW TIS

Connector X60004 (40-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60004 (40-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60004 (40-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
US version: Signal for heating to diagnosis module for tank leakage
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal to electric fan
Cavity: Populated
Confirmed

BMW TIS

Terminal 31, earth
Cavity: Populated
Confirmed

BMW TIS

Terminal 50E from CAS control unit
Cavity: Populated
Confirmed

BMW TIS

not E70
Earth wire to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Signal from accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Power supply to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Actuation of fuel-pump relay
Cavity: Populated
Confirmed

BMW TIS

E60, E61, E63, E64 and E70
Unknown function
Cavity: Unknown
Unknown
Earth wire to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Signal from accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Power supply to accelerator pedal module
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Engine-speed signal to diagnosis socket
Cavity: Populated
Confirmed

BMW TIS

not E70
Actuation of exhaust flap
Cavity: Populated
Confirmed

BMW TIS

not E70
Actuation of electronics box fan
Cavity: Populated
Confirmed

BMW TIS

US version: Actuation of leakage diagnosis pump
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Engine-speed signal from DSC control unit
Cavity: Populated
Confirmed

BMW TIS

Signal from clutch module
Cavity: Populated
Confirmed

BMW TIS

Signal from brake light switch
Cavity: Populated
Confirmed

BMW TIS

Signal from oil pressure switch via integrated supply module
Cavity: Populated
Confirmed

BMW TIS

E70: signal from oil pressure switch
Terminal 15 wake-up wire
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Signal from brake light test switch
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
US version: Signal from leakage diagnosis pump
Cavity: Populated
Confirmed

BMW TIS

Signal for active air flap control (introduction from 03/2007 on E60, E61)
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
EWS signal to CAS control unit
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
PT-CAN High
Cavity: Populated
Confirmed

BMW TIS

PT-CAN Low
Cavity: Populated
Confirmed

BMW TIS

Earth wire to temperature sensor at radiator outlet
Cavity: Populated
Confirmed

BMW TIS

Signal from temperature sensor on radiator outlet
Cavity: Populated
Confirmed

BMW TIS

Actuation of starter inhibitor relay in integrated supply module
Cavity: Populated
Confirmed

BMW TIS

E70: engine start signal from CAS

Connector X60005 (9-pin)

Redrawn pin index (face layout not shown in source)
View: Orientation and face layout not shown in source (pin index only)
Connector X60005 (9-pin) — Redrawn pin index (face layout not shown in source). Orientation and face layout not shown in source (pin index only)

Select a pin in a photograph or the index to highlight it.

Connector X60005 (9-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Actuation of no. 3 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 4 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 1 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 7 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Ignition earth
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 8 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 2 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Actuation of no. 6 cylinder ignition coil
Cavity: Populated
Confirmed

BMW TIS

Unknown function
Cavity: Unknown
Unknown