Scope
The BMW N62 V8 engine control unit (see Bosch ME9.2) is connected through five modular connectors, X60001 to X60005, of 9, 24, 52, 40 and 9 pins (134 in total). BMW's technical information system (TIS) publishes the pin assignments for the N62TU control unit, issue status 12/2007. This is manufacturer service documentation. The sheet does not itself name the Bosch designation, so its application to the ME9.2 control unit rests on the matching 9/24/52/40/9 connector layout; it should be checked against the wiring diagram for the individual vehicle.
Reading the tables
The diagrams are pin-index drawings: the source gives pin numbers and functions but not the connector face layout or viewing orientation. Pins that the source lists without a function are shown with an empty function. Entries limited to certain model lines (E60, E61, E63, E64, E70) or to the US version are noted against the pin. The source states that current pin assignments should be checked in BMW's diagnosis system. Pin 9 of X60005 is not legible in the extract used and is left blank.
Connector functions in outline
- X60001 (9-pin): power supply (terminals 30 and 87), earth and the engine-speed signal to the transmission control.
- X60002 (24-pin): oxygen sensor signals and heater outputs for both banks.
- X60003 (52-pin): injectors, VANOS solenoids, camshaft, crankshaft, knock and coolant sensors, air-mass and manifold-pressure sensors, throttle actuator, mapped thermostat and the local CAN link to the Valvetronic control unit.
- X60004 (40-pin): accelerator pedal module, PT-CAN, brake, clutch and oil-pressure switch inputs, fuel-pump relay, electric fan and electronics-box fan, and the CAS links.
- X60005 (9-pin): ignition coil outputs for cylinders 1 to 8 and ignition earth.
Diagram redrawn by Tuning Wiki from the BMW TIS sheet.
Sources
- BMW TIS, "DME control unit: N62TU", BMW AG technical information system sheet, issue status 12/2007, printed 23 December 2015, hosted on an independent E64 owner site. Accessed 19 November 2026.
Connector pinout
BMW TIS sheet "DME control unit: N62TU" (issue status 12/2007), five connectors X60001-X60005 of 9, 24, 52, 40 and 9 pins. OEM service documentation; the sheet does not name the Bosch designation, so applicability to the ME9.2 N62 control unit is inferred from the matching connector layout. Some functions apply to specific model lines (E70, US version) as noted.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
Connector X60001 (9-pin)
View: Orientation and face layout not shown in source (pin index only)
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Engine speed signal to electronic transmission control fed though integrated supply module (TxD wire) Cavity: Populated |
Confirmed BMW TIS |
not E70 | |
| Terminal 31, earth Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Terminal 31, earth Cavity: Populated |
Confirmed BMW TIS |
||
| Terminal 30 from integrated supply module, power supply Cavity: Populated |
Confirmed BMW TIS |
E70: terminal 30 from front power distributor in the junction box | |
| Terminal 87 from integrated supply module, power supply Cavity: Populated |
Confirmed BMW TIS |
E70: terminal 87 from front power distributor in the junction box | |
| Terminal 30 for switching the DME main relay Cavity: Populated |
Confirmed BMW TIS |
E70 only |
Connector X60002 (24-pin)
View: Orientation and face layout not shown in source (pin index only)
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Oxygen sensor heating for oxygen sensor upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Oxygen sensor heating for oxygen sensor 2 upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Oxygen sensor heating for oxygen sensor downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor 2 downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor 2 upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Oxygen sensor heating for oxygen sensor 2 downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oxygen sensor 2 downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to oxygen sensor 2 upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oxygen sensor downstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal from oxygen sensor upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oxygen sensor upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oxygen sensor 2 upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oxygen sensor 2 upstream of catalytic converter Cavity: Populated |
Confirmed BMW TIS |
||
| Terminal 85 from integrated supply module, power supply Cavity: Populated |
Confirmed BMW TIS |
not E70 | |
| Unknown function Cavity: Unknown |
Unknown |
Connector X60003 (52-pin)
View: Orientation and face layout not shown in source (pin index only)
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal from inlet pipe pressure sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from intake air temperature sensor in hot-film air-mass sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Power supply for intake pipe pressure sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from hot-film air-mass sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 4 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 5 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 6 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of VANOS solenoid valve 2 - inlet Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of VANOS solenoid valve - inlet Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 7 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of mapped thermostat Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 1 Cavity: Populated |
Confirmed BMW TIS |
||
| Earth wire to hot-film air mass meter, intake manifold pressure sensor and coolant temperature sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal from exhaust camshaft sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from exhaust camshaft sensor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal wire to Valvetronic control unit Cavity: Populated |
Confirmed BMW TIS |
||
| Bitserial data interface to alternator and oil condition sensor Cavity: Populated |
Confirmed BMW TIS |
E60, E61, E63, E64 and E70: also the intelligent battery sensor | |
| Actuation of VANOS solenoid valve - exhaust Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel evaporation control valve Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Actuation of VANOS solenoid valve 2 - exhaust Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 8 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel injector for cylinder 3 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from crankshaft sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from coolant-temperature sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from inlet camshaft sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from inlet camshaft sensor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from throttle-valve actuator (potentiometer 1) Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from throttle-valve actuator (potentiometer 2) Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to knock sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to knock sensor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to knock sensor 3 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal to knock sensor 4 Cavity: Populated |
Confirmed BMW TIS |
||
| Earth wire to crankshaft sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Local CAN (High) between DME control unit and Valvetronic control unit Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Actuation of DISA servomotor and DISA servomotor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of DISA servomotor and DISA servomotor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of throttle-valve actuator Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of throttle-valve actuator Cavity: Populated |
Confirmed BMW TIS |
||
| Reference voltage to air-mass flow sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal from knock sensor Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from knock sensor 2 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from knock sensor 3 Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from knock sensor 4 Cavity: Populated |
Confirmed BMW TIS |
||
| Power supply to throttle-valve actuator Cavity: Populated |
Confirmed BMW TIS |
||
| Local CAN (Low) between DME control unit and Valvetronic control unit Cavity: Populated |
Confirmed BMW TIS |
||
| Earth wire to throttle-valve actuator Cavity: Populated |
Confirmed BMW TIS |
Connector X60004 (40-pin)
View: Orientation and face layout not shown in source (pin index only)
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Unknown function Cavity: Unknown |
Unknown | ||
| US version: Signal for heating to diagnosis module for tank leakage Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal to electric fan Cavity: Populated |
Confirmed BMW TIS |
||
| Terminal 31, earth Cavity: Populated |
Confirmed BMW TIS |
||
| Terminal 50E from CAS control unit Cavity: Populated |
Confirmed BMW TIS |
not E70 | |
| Earth wire to accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Power supply to accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of fuel-pump relay Cavity: Populated |
Confirmed BMW TIS |
E60, E61, E63, E64 and E70 | |
| Unknown function Cavity: Unknown |
Unknown | ||
| Earth wire to accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Power supply to accelerator pedal module Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Engine-speed signal to diagnosis socket Cavity: Populated |
Confirmed BMW TIS |
not E70 | |
| Actuation of exhaust flap Cavity: Populated |
Confirmed BMW TIS |
not E70 | |
| Actuation of electronics box fan Cavity: Populated |
Confirmed BMW TIS |
||
| US version: Actuation of leakage diagnosis pump Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Engine-speed signal from DSC control unit Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from clutch module Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from brake light switch Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from oil pressure switch via integrated supply module Cavity: Populated |
Confirmed BMW TIS |
E70: signal from oil pressure switch | |
| Terminal 15 wake-up wire Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Signal from brake light test switch Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| US version: Signal from leakage diagnosis pump Cavity: Populated |
Confirmed BMW TIS |
||
| Signal for active air flap control (introduction from 03/2007 on E60, E61) Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| EWS signal to CAS control unit Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| PT-CAN High Cavity: Populated |
Confirmed BMW TIS |
||
| PT-CAN Low Cavity: Populated |
Confirmed BMW TIS |
||
| Earth wire to temperature sensor at radiator outlet Cavity: Populated |
Confirmed BMW TIS |
||
| Signal from temperature sensor on radiator outlet Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of starter inhibitor relay in integrated supply module Cavity: Populated |
Confirmed BMW TIS |
E70: engine start signal from CAS |
Connector X60005 (9-pin)
View: Orientation and face layout not shown in source (pin index only)
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Actuation of no. 3 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 4 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 1 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 7 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Ignition earth Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 8 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 2 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Actuation of no. 6 cylinder ignition coil Cavity: Populated |
Confirmed BMW TIS |
||
| Unknown function Cavity: Unknown |
Unknown |