Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Adaptronic standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 3 to revision 3
Removed text is struck through; added text is highlighted.
Adaptronic M6000 is a standalone or earlier programmable engine-management system. Modular M6000 universal wire-in ECU. Manufacturer support archives the M6000 Rev2 diagram, its startup guide and Eugene software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic M6000 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Adaptronic M6000 model informationWiring, manuals or technical archiveAdaptronic manufacturer index
Connector pinout
A structured pinout with redrawn pin-index diagrams of connectors J1, J2, J3 and J4 (120 positions, manufacturer documentation) is on Adaptronic M6000 connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic M6000 wiring diagrams.
Manufacturer connector pinouts
Transcribed from the Adaptronic M6000 wiring diagrams in Haltech's archive. The source states all J3 and J4 positions are normally blank and not connected internally unless the appropriate modules are installed. Their listed functions are conditional on those modules; spare positions on J1, J3 and J4 may be allocated by the small modules shown on the final source sheet. Confirm fitted hardware before wiring. The diagrams require external ignition drivers or coils with built-in igniters; see the source for wiring orientation, wire colours, current limits, power supplies and ECU configuration.
J1 — 26-way
PinFunction in drawing1Injector 12Injector 23Injector 34Injector 45Injector 56Spare7Spare8Injector 69Ignition 110Ignition 211Ignition 312Ignition 413Spare14Injector 715Ignition 516Ignition 617Ignition 718Ignition 819Spare20Injector 821Auxiliary 122Auxiliary 223Auxiliary 324Auxiliary 425Spare26Spare
J2 — 34-way
PinFunction in drawing1CAS 12CAS 23Internal MAP / IMAP4Fuel pressure5Engine coolant temperature6Servo712 V ECU supply8Power ground9Power ground10Sensor ground11CAS 312Exhaust manifold pressure / EMAP13Oil pressure14Manifold air temperature15CAN high16EFI / fuel pump relay17Ignition switch (source says need not be wired)18Oxygen 119Oxygen 220TPS 121Fuel temperature22External 0–5 V input 123CAN low24Vehicle speed sensor25Tachometer26Knock275 V sensor supply28TPS 229Oil temperature30External 0–5 V input 231Digital input 132Digital input 233Digital input 334Digital input 4
J3 — 26-way
PinFunction in drawing1Injector 92Injector 103Injector 114Injector 125Injector 136Spare / optional module7Spare / optional module8Injector 149Ignition 910Ignition 1011Ignition 1112Ignition 1213Spare / optional module14Injector 1515Ignition 1316Ignition 1417Ignition 1518Ignition 1619Spare / optional module20Injector 1621Auxiliary output22Auxiliary output23Auxiliary output24Auxiliary output25Spare / optional module26Spare / optional module
J4 — 34-way
PinFunction in drawing1Injector 172Injector 183Injector 194Injector 205Injector 216Spare / optional module7Spare / optional module8Spare / optional module9Spare / optional module10Injector 2211Ignition 1712Ignition 1813Ignition 1914Ignition 2015Spare / optional module16CAN 2 high17Spare / optional module18Injector 2319Ignition 2120Ignition 2221Ignition 2322Ignition 2423Spare / optional module24CAN 2 low25Spare / optional module26Injector 2427Auxiliary output28Auxiliary output29Auxiliary output30Auxiliary output31Spare / optional module32Spare / optional module33Spare / optional module34Spare / optional module
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Adaptronic M6000
Adaptronic M6000 is a standalone or earlier programmable engine-management system. Modular M6000 universal wire-in ECU. Manufacturer support archives the M6000 Rev2 diagram, its startup guide and Eugene software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic M6000 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Connector pinout
A structured pinout with redrawn pin-index diagrams of connectors J1, J2, J3 and J4 (120 positions, manufacturer documentation) is on Adaptronic M6000 connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic M6000 wiring diagrams.
Manufacturer connector pinouts
Transcribed from the Adaptronic M6000 wiring diagrams in Haltech's archive. The source states all J3 and J4 positions are normally blank and not connected internally unless the appropriate modules are installed. Their listed functions are conditional on those modules; spare positions on J1, J3 and J4 may be allocated by the small modules shown on the final source sheet. Confirm fitted hardware before wiring. The diagrams require external ignition drivers or coils with built-in igniters; see the source for wiring orientation, wire colours, current limits, power supplies and ECU configuration.
J1 — 26-way
| Pin | Function in drawing |
|---|
| 1 | Injector 1 |
| 2 | Injector 2 |
| 3 | Injector 3 |
| 4 | Injector 4 |
| 5 | Injector 5 |
| 6 | Spare |
| 7 | Spare |
| 8 | Injector 6 |
| 9 | Ignition 1 |
| 10 | Ignition 2 |
| 11 | Ignition 3 |
| 12 | Ignition 4 |
| 13 | Spare |
| 14 | Injector 7 |
| 15 | Ignition 5 |
| 16 | Ignition 6 |
| 17 | Ignition 7 |
| 18 | Ignition 8 |
| 19 | Spare |
| 20 | Injector 8 |
| 21 | Auxiliary 1 |
| 22 | Auxiliary 2 |
| 23 | Auxiliary 3 |
| 24 | Auxiliary 4 |
| 25 | Spare |
| 26 | Spare |
J2 — 34-way
| Pin | Function in drawing |
|---|
| 1 | CAS 1 |
| 2 | CAS 2 |
| 3 | Internal MAP / IMAP |
| 4 | Fuel pressure |
| 5 | Engine coolant temperature |
| 6 | Servo |
| 7 | 12 V ECU supply |
| 8 | Power ground |
| 9 | Power ground |
| 10 | Sensor ground |
| 11 | CAS 3 |
| 12 | Exhaust manifold pressure / EMAP |
| 13 | Oil pressure |
| 14 | Manifold air temperature |
| 15 | CAN high |
| 16 | EFI / fuel pump relay |
| 17 | Ignition switch (source says need not be wired) |
| 18 | Oxygen 1 |
| 19 | Oxygen 2 |
| 20 | TPS 1 |
| 21 | Fuel temperature |
| 22 | External 0–5 V input 1 |
| 23 | CAN low |
| 24 | Vehicle speed sensor |
| 25 | Tachometer |
| 26 | Knock |
| 27 | 5 V sensor supply |
| 28 | TPS 2 |
| 29 | Oil temperature |
| 30 | External 0–5 V input 2 |
| 31 | Digital input 1 |
| 32 | Digital input 2 |
| 33 | Digital input 3 |
| 34 | Digital input 4 |
J3 — 26-way
| Pin | Function in drawing |
|---|
| 1 | Injector 9 |
| 2 | Injector 10 |
| 3 | Injector 11 |
| 4 | Injector 12 |
| 5 | Injector 13 |
| 6 | Spare / optional module |
| 7 | Spare / optional module |
| 8 | Injector 14 |
| 9 | Ignition 9 |
| 10 | Ignition 10 |
| 11 | Ignition 11 |
| 12 | Ignition 12 |
| 13 | Spare / optional module |
| 14 | Injector 15 |
| 15 | Ignition 13 |
| 16 | Ignition 14 |
| 17 | Ignition 15 |
| 18 | Ignition 16 |
| 19 | Spare / optional module |
| 20 | Injector 16 |
| 21 | Auxiliary output |
| 22 | Auxiliary output |
| 23 | Auxiliary output |
| 24 | Auxiliary output |
| 25 | Spare / optional module |
| 26 | Spare / optional module |
J4 — 34-way
| Pin | Function in drawing |
|---|
| 1 | Injector 17 |
| 2 | Injector 18 |
| 3 | Injector 19 |
| 4 | Injector 20 |
| 5 | Injector 21 |
| 6 | Spare / optional module |
| 7 | Spare / optional module |
| 8 | Spare / optional module |
| 9 | Spare / optional module |
| 10 | Injector 22 |
| 11 | Ignition 17 |
| 12 | Ignition 18 |
| 13 | Ignition 19 |
| 14 | Ignition 20 |
| 15 | Spare / optional module |
| 16 | CAN 2 high |
| 17 | Spare / optional module |
| 18 | Injector 23 |
| 19 | Ignition 21 |
| 20 | Ignition 22 |
| 21 | Ignition 23 |
| 22 | Ignition 24 |
| 23 | Spare / optional module |
| 24 | CAN 2 low |
| 25 | Spare / optional module |
| 26 | Injector 24 |
| 27 | Auxiliary output |
| 28 | Auxiliary output |
| 29 | Auxiliary output |
| 30 | Auxiliary output |
| 31 | Spare / optional module |
| 32 | Spare / optional module |
| 33 | Spare / optional module |
| 34 | Spare / optional module |
Revision 3: Adaptronic M6000
Adaptronic M6000 is a standalone or earlier programmable engine-management system. Modular M6000 universal wire-in ECU. Manufacturer support archives the M6000 Rev2 diagram, its startup guide and Eugene software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic M6000 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Connector pinout
A structured pinout with redrawn pin-index diagrams of connectors J1, J2, J3 and J4 (120 positions, manufacturer documentation) is on Adaptronic M6000 connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic M6000 wiring diagrams.
Manufacturer connector pinouts
Transcribed from the Adaptronic M6000 wiring diagrams in Haltech's archive. The source states all J3 and J4 positions are normally blank and not connected internally unless the appropriate modules are installed. Their listed functions are conditional on those modules; spare positions on J1, J3 and J4 may be allocated by the small modules shown on the final source sheet. Confirm fitted hardware before wiring. The diagrams require external ignition drivers or coils with built-in igniters; see the source for wiring orientation, wire colours, current limits, power supplies and ECU configuration.
J1 — 26-way
| Pin | Function in drawing |
|---|
| 1 | Injector 1 |
| 2 | Injector 2 |
| 3 | Injector 3 |
| 4 | Injector 4 |
| 5 | Injector 5 |
| 6 | Spare |
| 7 | Spare |
| 8 | Injector 6 |
| 9 | Ignition 1 |
| 10 | Ignition 2 |
| 11 | Ignition 3 |
| 12 | Ignition 4 |
| 13 | Spare |
| 14 | Injector 7 |
| 15 | Ignition 5 |
| 16 | Ignition 6 |
| 17 | Ignition 7 |
| 18 | Ignition 8 |
| 19 | Spare |
| 20 | Injector 8 |
| 21 | Auxiliary 1 |
| 22 | Auxiliary 2 |
| 23 | Auxiliary 3 |
| 24 | Auxiliary 4 |
| 25 | Spare |
| 26 | Spare |
J2 — 34-way
| Pin | Function in drawing |
|---|
| 1 | CAS 1 |
| 2 | CAS 2 |
| 3 | Internal MAP / IMAP |
| 4 | Fuel pressure |
| 5 | Engine coolant temperature |
| 6 | Servo |
| 7 | 12 V ECU supply |
| 8 | Power ground |
| 9 | Power ground |
| 10 | Sensor ground |
| 11 | CAS 3 |
| 12 | Exhaust manifold pressure / EMAP |
| 13 | Oil pressure |
| 14 | Manifold air temperature |
| 15 | CAN high |
| 16 | EFI / fuel pump relay |
| 17 | Ignition switch (source says need not be wired) |
| 18 | Oxygen 1 |
| 19 | Oxygen 2 |
| 20 | TPS 1 |
| 21 | Fuel temperature |
| 22 | External 0–5 V input 1 |
| 23 | CAN low |
| 24 | Vehicle speed sensor |
| 25 | Tachometer |
| 26 | Knock |
| 27 | 5 V sensor supply |
| 28 | TPS 2 |
| 29 | Oil temperature |
| 30 | External 0–5 V input 2 |
| 31 | Digital input 1 |
| 32 | Digital input 2 |
| 33 | Digital input 3 |
| 34 | Digital input 4 |
J3 — 26-way
| Pin | Function in drawing |
|---|
| 1 | Injector 9 |
| 2 | Injector 10 |
| 3 | Injector 11 |
| 4 | Injector 12 |
| 5 | Injector 13 |
| 6 | Spare / optional module |
| 7 | Spare / optional module |
| 8 | Injector 14 |
| 9 | Ignition 9 |
| 10 | Ignition 10 |
| 11 | Ignition 11 |
| 12 | Ignition 12 |
| 13 | Spare / optional module |
| 14 | Injector 15 |
| 15 | Ignition 13 |
| 16 | Ignition 14 |
| 17 | Ignition 15 |
| 18 | Ignition 16 |
| 19 | Spare / optional module |
| 20 | Injector 16 |
| 21 | Auxiliary output |
| 22 | Auxiliary output |
| 23 | Auxiliary output |
| 24 | Auxiliary output |
| 25 | Spare / optional module |
| 26 | Spare / optional module |
J4 — 34-way
| Pin | Function in drawing |
|---|
| 1 | Injector 17 |
| 2 | Injector 18 |
| 3 | Injector 19 |
| 4 | Injector 20 |
| 5 | Injector 21 |
| 6 | Spare / optional module |
| 7 | Spare / optional module |
| 8 | Spare / optional module |
| 9 | Spare / optional module |
| 10 | Injector 22 |
| 11 | Ignition 17 |
| 12 | Ignition 18 |
| 13 | Ignition 19 |
| 14 | Ignition 20 |
| 15 | Spare / optional module |
| 16 | CAN 2 high |
| 17 | Spare / optional module |
| 18 | Injector 23 |
| 19 | Ignition 21 |
| 20 | Ignition 22 |
| 21 | Ignition 23 |
| 22 | Ignition 24 |
| 23 | Spare / optional module |
| 24 | CAN 2 low |
| 25 | Spare / optional module |
| 26 | Injector 24 |
| 27 | Auxiliary output |
| 28 | Auxiliary output |
| 29 | Auxiliary output |
| 30 | Auxiliary output |
| 31 | Spare / optional module |
| 32 | Spare / optional module |
| 33 | Spare / optional module |
| 34 | Spare / optional module |