Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MegaSquirt and MS3Pro standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

AMPd MicroSquirt is a MegaSquirt-family engine-management product. AMP'd MicroSquirt is DIYAutoTune's separately identified MicroSquirt-derived ECU; the supplier provides a supplemental guide in addition to the MicroSquirt manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware, and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Processor

The MicroSquirt is a sealed, fully assembled MegaSquirt-II-class unit; secondary sources (Wikipedia's MegaSquirt comparison and a vendor product page) give its microcontroller as the Freescale MC9S12C64, a 16-bit part at about 24 MHz. The MicroSquirt hardware guide describes the unit running MS2/Extra firmware but does not name the chip, and AMP EFI's supplement does not state the processor of the AMP'd variant, so the MC9S12C64 identification for the AMP'd version is inferred from the MicroSquirt family and is not confirmed by AMP EFI.

Engine applications

The MicroSquirt is a universal ECU, typically installed in the cabin away from engine heat (temperature limit 85 degC per the hardware guide), and suits cars and motorcycles. It controls fuel and spark through two injector bank outputs, two logic-level spark outputs, an idle valve output and a fuel pump output. AMP EFI's 2019 supplement for the V3.0 AMP'd unit adds four internal option switches: two (SW1, SW2) turn the ALED and WLED outputs into logic-level ignition outputs for three- or four-coil applications, and two (SW3, SW4) enable 1000 ohm pull-ups on the crank and cam inputs for Hall or optical sensors; with them off the inputs accept VR sensors. No engine codes or vehicle lists are given in the documents checked.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

The MicroSquirt Hardware Guide 3.4 (community-written manual linked by DIYAutoTune as the complete user manual) tabulates a 35-pin harness connector: for example 1 +12 V in, 2 and 3 CAN high/low, 9 and 10 injector outputs, 11 and 12 spark outputs, 22 and 23 power ground, 24 MAP, 25 CLT, 26 MAT, 27 TPS, 32 and 33 crank VR input, 34 O2, and 35 tacho; pins 16 and 17 are the ALED/WLED outputs that AMP EFI's supplement describes. Applicability of that table to the AMP'd variant is likely but not confirmed by AMP EFI. A structured pinout article has not yet been drawn.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Sources

AMP'd MicroSquirt V3.0 Supplement. AMP EFI manufacturer document, May 2019. Accessed 19 November 2026.Microsquirt Hardware Guide 3.4. Community-written manual, 2016. Accessed 19 November 2026.MegaSquirt. Wikipedia, secondary source for the MC9S12C64. Accessed 19 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: AMPd MicroSquirt

AMPd MicroSquirt is a MegaSquirt-family engine-management product. AMP'd MicroSquirt is DIYAutoTune's separately identified MicroSquirt-derived ECU; the supplier provides a supplemental guide in addition to the MicroSquirt manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware, and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Processor

The MicroSquirt is a sealed, fully assembled MegaSquirt-II-class unit; secondary sources (Wikipedia's MegaSquirt comparison and a vendor product page) give its microcontroller as the Freescale MC9S12C64, a 16-bit part at about 24 MHz. The MicroSquirt hardware guide describes the unit running MS2/Extra firmware but does not name the chip, and AMP EFI's supplement does not state the processor of the AMP'd variant, so the MC9S12C64 identification for the AMP'd version is inferred from the MicroSquirt family and is not confirmed by AMP EFI.

Engine applications

The MicroSquirt is a universal ECU, typically installed in the cabin away from engine heat (temperature limit 85 degC per the hardware guide), and suits cars and motorcycles. It controls fuel and spark through two injector bank outputs, two logic-level spark outputs, an idle valve output and a fuel pump output. AMP EFI's 2019 supplement for the V3.0 AMP'd unit adds four internal option switches: two (SW1, SW2) turn the ALED and WLED outputs into logic-level ignition outputs for three- or four-coil applications, and two (SW3, SW4) enable 1000 ohm pull-ups on the crank and cam inputs for Hall or optical sensors; with them off the inputs accept VR sensors. No engine codes or vehicle lists are given in the documents checked.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

The MicroSquirt Hardware Guide 3.4 (community-written manual linked by DIYAutoTune as the complete user manual) tabulates a 35-pin harness connector: for example 1 +12 V in, 2 and 3 CAN high/low, 9 and 10 injector outputs, 11 and 12 spark outputs, 22 and 23 power ground, 24 MAP, 25 CLT, 26 MAT, 27 TPS, 32 and 33 crank VR input, 34 O2, and 35 tacho; pins 16 and 17 are the ALED/WLED outputs that AMP EFI's supplement describes. Applicability of that table to the AMP'd variant is likely but not confirmed by AMP EFI. A structured pinout article has not yet been drawn.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Sources

Revision 2: AMPd MicroSquirt

AMPd MicroSquirt is a MegaSquirt-family engine-management product. AMP'd MicroSquirt is DIYAutoTune's separately identified MicroSquirt-derived ECU; the supplier provides a supplemental guide in addition to the MicroSquirt manual. Model source.

Identification and software

Record the ECU label, processor generation, board revision, firmware, and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.

Processor

The MicroSquirt is a sealed, fully assembled MegaSquirt-II-class unit; secondary sources (Wikipedia's MegaSquirt comparison and a vendor product page) give its microcontroller as the Freescale MC9S12C64, a 16-bit part at about 24 MHz. The MicroSquirt hardware guide describes the unit running MS2/Extra firmware but does not name the chip, and AMP EFI's supplement does not state the processor of the AMP'd variant, so the MC9S12C64 identification for the AMP'd version is inferred from the MicroSquirt family and is not confirmed by AMP EFI.

Engine applications

The MicroSquirt is a universal ECU, typically installed in the cabin away from engine heat (temperature limit 85 degC per the hardware guide), and suits cars and motorcycles. It controls fuel and spark through two injector bank outputs, two logic-level spark outputs, an idle valve output and a fuel pump output. AMP EFI's 2019 supplement for the V3.0 AMP'd unit adds four internal option switches: two (SW1, SW2) turn the ALED and WLED outputs into logic-level ignition outputs for three- or four-coil applications, and two (SW3, SW4) enable 1000 ohm pull-ups on the crank and cam inputs for Hall or optical sensors; with them off the inputs accept VR sensors. No engine codes or vehicle lists are given in the documents checked.

Wiring and pinout

Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.

The MicroSquirt Hardware Guide 3.4 (community-written manual linked by DIYAutoTune as the complete user manual) tabulates a 35-pin harness connector: for example 1 +12 V in, 2 and 3 CAN high/low, 9 and 10 injector outputs, 11 and 12 spark outputs, 22 and 23 power ground, 24 MAP, 25 CLT, 26 MAT, 27 TPS, 32 and 33 crank VR input, 34 O2, and 35 tacho; pins 16 and 17 are the ALED/WLED outputs that AMP EFI's supplement describes. Applicability of that table to the AMP'd variant is likely but not confirmed by AMP EFI. A structured pinout article has not yet been drawn.

See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.

Sources