Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Autronic SM4
Applies to
Autronic SM4
Tool groups
None
Manufacturers
Autronic

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

The Autronic SM4 standalone engine ECU uses a single 42-way main connector. This reference gives the function of every pin as published by Autronic, with the manufacturer's current and frequency limits and the wire colour used in the standard Autronic loom. The same assignment applies to the SM4DC dual-calibration and SM4 Marine versions, which Autronic wires with the standard SM4 loom; on SM4DC units pin 39 is the calibration select input instead of a speed input.

Connector layout

The Autronic wiring drawing shows the connector from the wire side in three staggered columns of fourteen: pins 1–14, 15–28 and 29–42, with the lowest number of each column at the bottom. The interactive diagram on this page follows that arrangement; cavity spacing is schematic, so terminal positions should be checked against the actual housing before wiring.

Pin groups

Supplies and grounds: 1 ignition-on input, 15 main +12 V supply, 30 keep-alive memory supply, 29 power ground, 22 sensor ground, 36 +5 V sensor supply (45 mA), 11 +8 V trigger supply (30 mA).Injectors: 17, 32, 31 and 16 form group 1–4; 4, 18, 3 and 2 form group 5–8. Injectors 6, 7 and 8 (pins 18, 3 and 2) can instead be used as switch-to-ground inputs.Ignition: 5, 6, 19 and 33, push-pull, 0.8 A continuous.Triggers: 25/40 cylinder and 26/41 sync inputs for Hall or reluctor sensors; the negative inputs are left unconnected with Hall sensors.Auxiliary outputs: outputs 1–4 (7, 34, 20, 35) are push-pull stepper-capable drivers; outputs 5–8 (27, 13, 42, 12) and PWM 1–2 (28, 14) are open-collector.Sensor inputs: 9 coolant, 23 air temperature, 21 throttle position, 37 oxygen, 8 and 38 analogue, 10, 24 and 39 high-speed inputs.

Manufacturer cautions

Pin 22 is a dedicated sensor ground and must not be joined to the engine block or vehicle ground. The ECU measures pin 15 as battery voltage for injector dead-time compensation, so pin 15 must be fed from the same supply as the injectors. Ignition 2–4 and injector outputs used for other loads are limited to ON/OFF or 10 Hz PWM operation.

Diagram redrawn by Tuning Wiki from the Autronic SM4 Wiring Basic drawing and the Autronic SM4 pin-function table.

Not established

The connector housing manufacturer and part number, and the exact physical cavity pitch, are not stated in the cited Autronic documents.

Sources

Autronic SM4 – Input / Output Pin Functions. Autronic, manufacturer pin-function table, 12 October 2016. Accessed 19 November 2026.SM4 Wiring Basic. Aubert Electronics Pty Ltd, manufacturer wiring diagram SM4_0001, revision 3.4, 23 September 2014; connector shown from the wire side. Accessed 19 November 2026.SM4 ECU. Autronic, manufacturer product and specification page. Accessed 19 November 2026.

Pinout changes

Applicability: Autronic SM4, SM4DC (dual calibration) and SM4 Marine with the standard 42-way loom. Manufacturer documentation (Autronic pin-function table dated 12 October 2016 and SM4 Wiring Basic drawing rev. 3.4, 23 September 2014). Loom colours are those of the Autronic standard harness and may differ on custom looms.

Connector Main connector (42-way):

Main connector (42-way) pin 1: Ignition switch input; confidence: confirmed; state: populated

Main connector (42-way) pin 1 notes: Ignition-on supply, <100 mA. Standard loom colour PUR.

Main connector (42-way) pin 1 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 2: Injector 8 / switch input 3; confidence: confirmed; state: populated

Main connector (42-way) pin 2 notes: Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom BLU/RED.

Main connector (42-way) pin 2 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 3: Injector 7 / switch input 2; confidence: confirmed; state: populated

Main connector (42-way) pin 3 notes: Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom GRY/BLU.

Main connector (42-way) pin 3 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 4: Injector 5; confidence: confirmed; state: populated

Main connector (42-way) pin 4 notes: Injector group 5-8, selectable peak/hold current. Loom GRN/YEL.

Main connector (42-way) pin 4 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 5: Ignition 1; confidence: confirmed; state: populated

Main connector (42-way) pin 5 notes: Ignition trigger, push-pull, 0.8 A continuous (1 A peak). Loom PNK/WHT.

Main connector (42-way) pin 5 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 6: Ignition 2; confidence: confirmed; state: populated

Main connector (42-way) pin 6 notes: Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom PNK/BLK.

Main connector (42-way) pin 6 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 7: Output 1; confidence: confirmed; state: populated

Main connector (42-way) pin 7 notes: Stepper motor or push-pull output, 0.8 A; ON/OFF, 10-500 Hz PWM or H-bridge. Loom RED/GRN.

Main connector (42-way) pin 7 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 8: Analogue input 1; confidence: confirmed; state: populated

Main connector (42-way) pin 8 notes: Spare temperature/pressure, potentiometer or high-side switch; 2-wire sensors need a pull-up. Loom GRY/BLU.

Main connector (42-way) pin 8 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 9: Coolant temperature input; confidence: confirmed; state: populated

Main connector (42-way) pin 9 notes: Most NTC or PTC sensors. Loom PNK.

Main connector (42-way) pin 9 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 10: HSI 1; confidence: confirmed; state: populated

Main connector (42-way) pin 10 notes: Speed or camshaft-position input; alternate switch or digital airflow; 7 kHz max. Loom BLU.

Main connector (42-way) pin 10 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 11: +8 V trigger supply; confidence: confirmed; state: populated

Main connector (42-way) pin 11 notes: Hall and other sensors, 30 mA max. Loom RED/BLK.

Main connector (42-way) pin 11 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 12: Output 8 / tacho; confidence: confirmed; state: populated

Main connector (42-way) pin 12 notes: Open collector, 1 A; constant or switched supply. Loom GRY/BLK.

Main connector (42-way) pin 12 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 13: Output 6; confidence: confirmed; state: populated

Main connector (42-way) pin 13 notes: Open collector, 2.5 A. Loom BLU.

Main connector (42-way) pin 13 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 14: PWM 2; confidence: confirmed; state: populated

Main connector (42-way) pin 14 notes: Open collector 9.5-1220 Hz PWM, 3.5 A continuous (5 A peak). Loom BRN/WHT.

Main connector (42-way) pin 14 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 15: +12 V main supply; confidence: confirmed; state: populated

Main connector (42-way) pin 15 notes: Measured as battery voltage for injector dead-time compensation; supply must match the injectors. Loom RED.

Main connector (42-way) pin 15 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 16: Injector 4; confidence: confirmed; state: populated

Main connector (42-way) pin 16 notes: Injector group 1-4. Loom GRN/WHT.

Main connector (42-way) pin 16 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 17: Injector 1; confidence: confirmed; state: populated

Main connector (42-way) pin 17 notes: Injector group 1-4, selectable peak/hold current. Loom PNK/BLK.

Main connector (42-way) pin 17 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 18: Injector 6 / switch input 1; confidence: confirmed; state: populated

Main connector (42-way) pin 18 notes: Output in injector group 5-8 or switch-to-ground input (700 Hz max). Loom BLU/BLK.

Main connector (42-way) pin 18 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 19: Ignition 3; confidence: confirmed; state: populated

Main connector (42-way) pin 19 notes: Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom YEL/BLK.

Main connector (42-way) pin 19 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 20: Output 3; confidence: confirmed; state: populated

Main connector (42-way) pin 20 notes: Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom ORG/WHT.

Main connector (42-way) pin 20 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 21: Throttle position input; confidence: confirmed; state: populated

Main connector (42-way) pin 21 notes: Linear, voltage rising with opening. Loom ORG.

Main connector (42-way) pin 21 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 22: Signal ground; confidence: confirmed; state: populated

Main connector (42-way) pin 22 notes: Sensor ground; do not connect to engine block or vehicle ground. Loom BLK.

Main connector (42-way) pin 22 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 23: Air intake temperature input; confidence: confirmed; state: populated

Main connector (42-way) pin 23 notes: Autronic and most NTC/PTC sensors. Loom WHT.

Main connector (42-way) pin 23 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 24: HSI 2; confidence: confirmed; state: populated

Main connector (42-way) pin 24 notes: Switch or digital flex-fuel input; 7 kHz max. Loom GRN.

Main connector (42-way) pin 24 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 25: Cylinder trigger +; confidence: confirmed; state: populated

Main connector (42-way) pin 25 notes: Hall or reluctor input, generic and OEM trigger patterns. Loom WHT (screened).

Main connector (42-way) pin 25 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 26: Sync trigger +; confidence: confirmed; state: populated

Main connector (42-way) pin 26 notes: Hall or reluctor sync input; alternate speed input; 7 kHz max. Loom WHT (screened).

Main connector (42-way) pin 26 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 27: Output 5; confidence: confirmed; state: populated

Main connector (42-way) pin 27 notes: Open collector, 2.5 A. Loom PNK/YEL.

Main connector (42-way) pin 27 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 28: PWM 1; confidence: confirmed; state: populated

Main connector (42-way) pin 28 notes: Open collector 9.5-1220 Hz PWM, 5 A continuous (6 A peak). Loom RED/YEL.

Main connector (42-way) pin 28 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 29: Power ground; confidence: confirmed; state: populated

Main connector (42-way) pin 29 notes: Loom BLK.

Main connector (42-way) pin 29 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 30: +12 V RAM (keep-alive) supply; confidence: confirmed; state: populated

Main connector (42-way) pin 30 notes: Continuous supply, <1 mA. Loom RED.

Main connector (42-way) pin 30 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 31: Injector 3; confidence: confirmed; state: populated

Main connector (42-way) pin 31 notes: Injector group 1-4. Loom BLU/WHT.

Main connector (42-way) pin 31 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 32: Injector 2; confidence: confirmed; state: populated

Main connector (42-way) pin 32 notes: Injector group 1-4. Loom ORG/BLK.

Main connector (42-way) pin 32 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 33: Ignition 4; confidence: confirmed; state: populated

Main connector (42-way) pin 33 notes: Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom RED/WHT.

Main connector (42-way) pin 33 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 34: Output 2; confidence: confirmed; state: populated

Main connector (42-way) pin 34 notes: Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BLK/WHT.

Main connector (42-way) pin 34 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 35: Output 4; confidence: confirmed; state: populated

Main connector (42-way) pin 35 notes: Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BRN/BLK.

Main connector (42-way) pin 35 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 36: +5 V sensor supply; confidence: confirmed; state: populated

Main connector (42-way) pin 36 notes: TPS and other sensors, 45 mA max. Loom RED/WHT.

Main connector (42-way) pin 36 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 37: Oxygen / AFR input; confidence: confirmed; state: populated

Main connector (42-way) pin 37 notes: Loom BLU.

Main connector (42-way) pin 37 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 38: Analogue input 2; confidence: confirmed; state: populated

Main connector (42-way) pin 38 notes: External MAP/BARO; labelled 'Analog 2-3' on the wiring diagram. Loom GRN/BLK.

Main connector (42-way) pin 38 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 39: HSI 3 / dual-calibration select; confidence: confirmed; state: populated

Main connector (42-way) pin 39 notes: Speed input or switch, 2.2 kHz max; on SM4DC dual-calibration units this is the calibration select input. Loom GRY.

Main connector (42-way) pin 39 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 40: Cylinder trigger -; confidence: confirmed; state: populated

Main connector (42-way) pin 40 notes: Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).

Main connector (42-way) pin 40 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 41: Sync trigger -; confidence: confirmed; state: populated

Main connector (42-way) pin 41 notes: Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).

Main connector (42-way) pin 41 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) pin 42: Output 7; confidence: confirmed; state: populated

Main connector (42-way) pin 42 notes: Open collector, 3.5 A. Loom GRN/ORG.

Main connector (42-way) pin 42 evidence: Autronic pin table 2016; wiring rev 3.4

Main connector (42-way) view Redrawn connector, wire side: Harness connector viewed from the wire side, as drawn in the Autronic SM4 Wiring Basic drawing; cavity spacing schematic.

Main connector (42-way) view Redrawn connector, wire side image: e7de3fb3-aab3-49f2-bf9a-2337b31ea66dMain connector (42-way) view Redrawn connector, wire side image: fce8ed61-271f-46cc-bda7-90a162896417

Main connector (42-way) view Redrawn connector, wire side pin 14 position: 0.40200000000000002, 0.18099999999999999

Main connector (42-way) view Redrawn connector, wire side pin 13 position: 0.40200000000000002, 0.23100000000000001

Main connector (42-way) view Redrawn connector, wire side pin 12 position: 0.40200000000000002, 0.28100000000000003

Main connector (42-way) view Redrawn connector, wire side pin 11 position: 0.40200000000000002, 0.33100000000000002

Main connector (42-way) view Redrawn connector, wire side pin 10 position: 0.40200000000000002, 0.38100000000000001

Main connector (42-way) view Redrawn connector, wire side pin 9 position: 0.40200000000000002, 0.43099999999999999

Main connector (42-way) view Redrawn connector, wire side pin 8 position: 0.40200000000000002, 0.48099999999999998

Main connector (42-way) view Redrawn connector, wire side pin 7 position: 0.40200000000000002, 0.53100000000000003

Main connector (42-way) view Redrawn connector, wire side pin 6 position: 0.40200000000000002, 0.58099999999999996

Main connector (42-way) view Redrawn connector, wire side pin 5 position: 0.40200000000000002, 0.63100000000000001

Main connector (42-way) view Redrawn connector, wire side pin 4 position: 0.40200000000000002, 0.68100000000000005

Main connector (42-way) view Redrawn connector, wire side pin 3 position: 0.40200000000000002, 0.73099999999999998

Main connector (42-way) view Redrawn connector, wire side pin 2 position: 0.40200000000000002, 0.78100000000000003

Main connector (42-way) view Redrawn connector, wire side pin 1 position: 0.40200000000000002, 0.83099999999999996

Main connector (42-way) view Redrawn connector, wire side pin 28 position: 0.5, 0.16700000000000001

Main connector (42-way) view Redrawn connector, wire side pin 27 position: 0.5, 0.217

Main connector (42-way) view Redrawn connector, wire side pin 26 position: 0.5, 0.26700000000000002

Main connector (42-way) view Redrawn connector, wire side pin 25 position: 0.5, 0.317

Main connector (42-way) view Redrawn connector, wire side pin 24 position: 0.5, 0.36699999999999999

Main connector (42-way) view Redrawn connector, wire side pin 23 position: 0.5, 0.41699999999999998

Main connector (42-way) view Redrawn connector, wire side pin 22 position: 0.5, 0.46700000000000003

Main connector (42-way) view Redrawn connector, wire side pin 21 position: 0.5, 0.51700000000000002

Main connector (42-way) view Redrawn connector, wire side pin 20 position: 0.5, 0.56699999999999995

Main connector (42-way) view Redrawn connector, wire side pin 19 position: 0.5, 0.61699999999999999

Main connector (42-way) view Redrawn connector, wire side pin 18 position: 0.5, 0.66700000000000004

Main connector (42-way) view Redrawn connector, wire side pin 17 position: 0.5, 0.71699999999999997

Main connector (42-way) view Redrawn connector, wire side pin 16 position: 0.5, 0.76700000000000002

Main connector (42-way) view Redrawn connector, wire side pin 15 position: 0.5, 0.81699999999999995

Main connector (42-way) view Redrawn connector, wire side pin 42 position: 0.59799999999999998, 0.17599999999999999

Main connector (42-way) view Redrawn connector, wire side pin 41 position: 0.59799999999999998, 0.22600000000000001

Main connector (42-way) view Redrawn connector, wire side pin 40 position: 0.59799999999999998, 0.27600000000000002

Main connector (42-way) view Redrawn connector, wire side pin 39 position: 0.59799999999999998, 0.32600000000000001

Main connector (42-way) view Redrawn connector, wire side pin 38 position: 0.59799999999999998, 0.376

Main connector (42-way) view Redrawn connector, wire side pin 37 position: 0.59799999999999998, 0.42599999999999999

Main connector (42-way) view Redrawn connector, wire side pin 36 position: 0.59799999999999998, 0.47599999999999998

Main connector (42-way) view Redrawn connector, wire side pin 35 position: 0.59799999999999998, 0.52600000000000002

Main connector (42-way) view Redrawn connector, wire side pin 34 position: 0.59799999999999998, 0.57599999999999996

Main connector (42-way) view Redrawn connector, wire side pin 33 position: 0.59799999999999998, 0.626

Main connector (42-way) view Redrawn connector, wire side pin 32 position: 0.59799999999999998, 0.67600000000000005

Main connector (42-way) view Redrawn connector, wire side pin 31 position: 0.59799999999999998, 0.72599999999999998

Main connector (42-way) view Redrawn connector, wire side pin 30 position: 0.59799999999999998, 0.77600000000000002

Main connector (42-way) view Redrawn connector, wire side pin 29 position: 0.59799999999999998, 0.82599999999999996

Page organisation changed

FieldRevision 1Revision 3
Page typeTechnical articleTechnical article
SubjectEngine ECUEngine ECU
ParentAutronic SM4Autronic SM4
Applies toAutronic SM4Autronic SM4MR, Autronic SM4, Autronic SM4DC, Autronic SM4DCMR
Tool groupsNoneNone
Vehicle makesAutronicAutronic

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Autronic SM4 connector pinout

The Autronic SM4 standalone engine ECU uses a single 42-way main connector. This reference gives the function of every pin as published by Autronic, with the manufacturer's current and frequency limits and the wire colour used in the standard Autronic loom. The same assignment applies to the SM4DC dual-calibration and SM4 Marine versions, which Autronic wires with the standard SM4 loom; on SM4DC units pin 39 is the calibration select input instead of a speed input.

Connector layout

The Autronic wiring drawing shows the connector from the wire side in three staggered columns of fourteen: pins 1–14, 15–28 and 29–42, with the lowest number of each column at the bottom. The interactive diagram on this page follows that arrangement; cavity spacing is schematic, so terminal positions should be checked against the actual housing before wiring.

Pin groups

  • Supplies and grounds: 1 ignition-on input, 15 main +12 V supply, 30 keep-alive memory supply, 29 power ground, 22 sensor ground, 36 +5 V sensor supply (45 mA), 11 +8 V trigger supply (30 mA).
  • Injectors: 17, 32, 31 and 16 form group 1–4; 4, 18, 3 and 2 form group 5–8. Injectors 6, 7 and 8 (pins 18, 3 and 2) can instead be used as switch-to-ground inputs.
  • Ignition: 5, 6, 19 and 33, push-pull, 0.8 A continuous.
  • Triggers: 25/40 cylinder and 26/41 sync inputs for Hall or reluctor sensors; the negative inputs are left unconnected with Hall sensors.
  • Auxiliary outputs: outputs 1–4 (7, 34, 20, 35) are push-pull stepper-capable drivers; outputs 5–8 (27, 13, 42, 12) and PWM 1–2 (28, 14) are open-collector.
  • Sensor inputs: 9 coolant, 23 air temperature, 21 throttle position, 37 oxygen, 8 and 38 analogue, 10, 24 and 39 high-speed inputs.

Manufacturer cautions

Pin 22 is a dedicated sensor ground and must not be joined to the engine block or vehicle ground. The ECU measures pin 15 as battery voltage for injector dead-time compensation, so pin 15 must be fed from the same supply as the injectors. Ignition 2–4 and injector outputs used for other loads are limited to ON/OFF or 10 Hz PWM operation.

Diagram redrawn by Tuning Wiki from the Autronic SM4 Wiring Basic drawing and the Autronic SM4 pin-function table.

Not established

The connector housing manufacturer and part number, and the exact physical cavity pitch, are not stated in the cited Autronic documents.

Sources

  • Autronic SM4 – Input / Output Pin Functions. Autronic, manufacturer pin-function table, 12 October 2016. Accessed 19 November 2026.
  • SM4 Wiring Basic. Aubert Electronics Pty Ltd, manufacturer wiring diagram SM4_0001, revision 3.4, 23 September 2014; connector shown from the wire side. Accessed 19 November 2026.
  • SM4 ECU. Autronic, manufacturer product and specification page. Accessed 19 November 2026.

Connector pinout

Applicability

Autronic SM4, SM4DC (dual calibration) and SM4 Marine with the standard 42-way loom. Manufacturer documentation (Autronic pin-function table dated 12 October 2016 and SM4 Wiring Basic drawing rev. 3.4, 23 September 2014). Loom colours are those of the Autronic standard harness and may differ on custom looms.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

Main connector (42-way)

Redrawn connector, wire side
View: Harness connector viewed from the wire side, as drawn in the Autronic SM4 Wiring Basic drawing; cavity spacing schematic.
Main connector (42-way) — Redrawn connector, wire side. Harness connector viewed from the wire side, as drawn in the Autronic SM4 Wiring Basic drawing; cavity spacing schematic.

Select a pin in a photograph or the index to highlight it.

Main connector (42-way) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Ignition switch input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Ignition-on supply, <100 mA. Standard loom colour PUR.
Injector 8 / switch input 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom BLU/RED.
Injector 7 / switch input 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom GRY/BLU.
Injector 5
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 5-8, selectable peak/hold current. Loom GRN/YEL.
Ignition 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Ignition trigger, push-pull, 0.8 A continuous (1 A peak). Loom PNK/WHT.
Ignition 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom PNK/BLK.
Output 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Stepper motor or push-pull output, 0.8 A; ON/OFF, 10-500 Hz PWM or H-bridge. Loom RED/GRN.
Analogue input 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Spare temperature/pressure, potentiometer or high-side switch; 2-wire sensors need a pull-up. Loom GRY/BLU.
Coolant temperature input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Most NTC or PTC sensors. Loom PNK.
HSI 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Speed or camshaft-position input; alternate switch or digital airflow; 7 kHz max. Loom BLU.
+8 V trigger supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall and other sensors, 30 mA max. Loom RED/BLK.
Output 8 / tacho
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 1 A; constant or switched supply. Loom GRY/BLK.
Output 6
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 2.5 A. Loom BLU.
PWM 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector 9.5-1220 Hz PWM, 3.5 A continuous (5 A peak). Loom BRN/WHT.
+12 V main supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Measured as battery voltage for injector dead-time compensation; supply must match the injectors. Loom RED.
Injector 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom GRN/WHT.
Injector 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4, selectable peak/hold current. Loom PNK/BLK.
Injector 6 / switch input 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (700 Hz max). Loom BLU/BLK.
Ignition 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom YEL/BLK.
Output 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom ORG/WHT.
Throttle position input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Linear, voltage rising with opening. Loom ORG.
Signal ground
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Sensor ground; do not connect to engine block or vehicle ground. Loom BLK.
Air intake temperature input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Autronic and most NTC/PTC sensors. Loom WHT.
HSI 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Switch or digital flex-fuel input; 7 kHz max. Loom GRN.
Cylinder trigger +
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall or reluctor input, generic and OEM trigger patterns. Loom WHT (screened).
Sync trigger +
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall or reluctor sync input; alternate speed input; 7 kHz max. Loom WHT (screened).
Output 5
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 2.5 A. Loom PNK/YEL.
PWM 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector 9.5-1220 Hz PWM, 5 A continuous (6 A peak). Loom RED/YEL.
Power ground
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Loom BLK.
+12 V RAM (keep-alive) supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Continuous supply, <1 mA. Loom RED.
Injector 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom BLU/WHT.
Injector 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom ORG/BLK.
Ignition 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom RED/WHT.
Output 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BLK/WHT.
Output 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BRN/BLK.
+5 V sensor supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

TPS and other sensors, 45 mA max. Loom RED/WHT.
Oxygen / AFR input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Loom BLU.
Analogue input 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

External MAP/BARO; labelled 'Analog 2-3' on the wiring diagram. Loom GRN/BLK.
HSI 3 / dual-calibration select
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Speed input or switch, 2.2 kHz max; on SM4DC dual-calibration units this is the calibration select input. Loom GRY.
Cylinder trigger -
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).
Sync trigger -
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).
Output 7
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 3.5 A. Loom GRN/ORG.
Revision 3: Autronic SM4 connector pinout

The Autronic SM4 standalone engine ECU uses a single 42-way main connector. This reference gives the function of every pin as published by Autronic, with the manufacturer's current and frequency limits and the wire colour used in the standard Autronic loom. The same assignment applies to the SM4DC dual-calibration and SM4 Marine versions, which Autronic wires with the standard SM4 loom; on SM4DC units pin 39 is the calibration select input instead of a speed input.

Connector layout

The Autronic wiring drawing shows the connector from the wire side in three staggered columns of fourteen: pins 1–14, 15–28 and 29–42, with the lowest number of each column at the bottom. The interactive diagram on this page follows that arrangement; cavity spacing is schematic, so terminal positions should be checked against the actual housing before wiring.

Pin groups

  • Supplies and grounds: 1 ignition-on input, 15 main +12 V supply, 30 keep-alive memory supply, 29 power ground, 22 sensor ground, 36 +5 V sensor supply (45 mA), 11 +8 V trigger supply (30 mA).
  • Injectors: 17, 32, 31 and 16 form group 1–4; 4, 18, 3 and 2 form group 5–8. Injectors 6, 7 and 8 (pins 18, 3 and 2) can instead be used as switch-to-ground inputs.
  • Ignition: 5, 6, 19 and 33, push-pull, 0.8 A continuous.
  • Triggers: 25/40 cylinder and 26/41 sync inputs for Hall or reluctor sensors; the negative inputs are left unconnected with Hall sensors.
  • Auxiliary outputs: outputs 1–4 (7, 34, 20, 35) are push-pull stepper-capable drivers; outputs 5–8 (27, 13, 42, 12) and PWM 1–2 (28, 14) are open-collector.
  • Sensor inputs: 9 coolant, 23 air temperature, 21 throttle position, 37 oxygen, 8 and 38 analogue, 10, 24 and 39 high-speed inputs.

Manufacturer cautions

Pin 22 is a dedicated sensor ground and must not be joined to the engine block or vehicle ground. The ECU measures pin 15 as battery voltage for injector dead-time compensation, so pin 15 must be fed from the same supply as the injectors. Ignition 2–4 and injector outputs used for other loads are limited to ON/OFF or 10 Hz PWM operation.

Diagram redrawn by Tuning Wiki from the Autronic SM4 Wiring Basic drawing and the Autronic SM4 pin-function table.

Not established

The connector housing manufacturer and part number, and the exact physical cavity pitch, are not stated in the cited Autronic documents.

Sources

  • Autronic SM4 – Input / Output Pin Functions. Autronic, manufacturer pin-function table, 12 October 2016. Accessed 19 November 2026.
  • SM4 Wiring Basic. Aubert Electronics Pty Ltd, manufacturer wiring diagram SM4_0001, revision 3.4, 23 September 2014; connector shown from the wire side. Accessed 19 November 2026.
  • SM4 ECU. Autronic, manufacturer product and specification page. Accessed 19 November 2026.

Connector pinout

Applicability

Autronic SM4, SM4DC (dual calibration) and SM4 Marine with the standard 42-way loom. Manufacturer documentation (Autronic pin-function table dated 12 October 2016 and SM4 Wiring Basic drawing rev. 3.4, 23 September 2014). Loom colours are those of the Autronic standard harness and may differ on custom looms.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

Main connector (42-way)

Redrawn connector, wire side
View: Harness connector viewed from the wire side, as drawn in the Autronic SM4 Wiring Basic drawing; cavity spacing schematic.
Main connector (42-way) — Redrawn connector, wire side. Harness connector viewed from the wire side, as drawn in the Autronic SM4 Wiring Basic drawing; cavity spacing schematic.

Select a pin in a photograph or the index to highlight it.

Main connector (42-way) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Ignition switch input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Ignition-on supply, <100 mA. Standard loom colour PUR.
Injector 8 / switch input 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom BLU/RED.
Injector 7 / switch input 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (200 Hz max). Loom GRY/BLU.
Injector 5
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 5-8, selectable peak/hold current. Loom GRN/YEL.
Ignition 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Ignition trigger, push-pull, 0.8 A continuous (1 A peak). Loom PNK/WHT.
Ignition 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom PNK/BLK.
Output 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Stepper motor or push-pull output, 0.8 A; ON/OFF, 10-500 Hz PWM or H-bridge. Loom RED/GRN.
Analogue input 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Spare temperature/pressure, potentiometer or high-side switch; 2-wire sensors need a pull-up. Loom GRY/BLU.
Coolant temperature input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Most NTC or PTC sensors. Loom PNK.
HSI 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Speed or camshaft-position input; alternate switch or digital airflow; 7 kHz max. Loom BLU.
+8 V trigger supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall and other sensors, 30 mA max. Loom RED/BLK.
Output 8 / tacho
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 1 A; constant or switched supply. Loom GRY/BLK.
Output 6
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 2.5 A. Loom BLU.
PWM 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector 9.5-1220 Hz PWM, 3.5 A continuous (5 A peak). Loom BRN/WHT.
+12 V main supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Measured as battery voltage for injector dead-time compensation; supply must match the injectors. Loom RED.
Injector 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom GRN/WHT.
Injector 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4, selectable peak/hold current. Loom PNK/BLK.
Injector 6 / switch input 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Output in injector group 5-8 or switch-to-ground input (700 Hz max). Loom BLU/BLK.
Ignition 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom YEL/BLK.
Output 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom ORG/WHT.
Throttle position input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Linear, voltage rising with opening. Loom ORG.
Signal ground
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Sensor ground; do not connect to engine block or vehicle ground. Loom BLK.
Air intake temperature input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Autronic and most NTC/PTC sensors. Loom WHT.
HSI 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Switch or digital flex-fuel input; 7 kHz max. Loom GRN.
Cylinder trigger +
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall or reluctor input, generic and OEM trigger patterns. Loom WHT (screened).
Sync trigger +
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Hall or reluctor sync input; alternate speed input; 7 kHz max. Loom WHT (screened).
Output 5
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 2.5 A. Loom PNK/YEL.
PWM 1
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector 9.5-1220 Hz PWM, 5 A continuous (6 A peak). Loom RED/YEL.
Power ground
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Loom BLK.
+12 V RAM (keep-alive) supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Continuous supply, <1 mA. Loom RED.
Injector 3
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom BLU/WHT.
Injector 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Injector group 1-4. Loom ORG/BLK.
Ignition 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; alternate use ON/OFF or 10 Hz PWM only. Loom RED/WHT.
Output 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BLK/WHT.
Output 4
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Push-pull 0.8 A; stepper, ON/OFF, PWM or H-bridge. Loom BRN/BLK.
+5 V sensor supply
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

TPS and other sensors, 45 mA max. Loom RED/WHT.
Oxygen / AFR input
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Loom BLU.
Analogue input 2
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

External MAP/BARO; labelled 'Analog 2-3' on the wiring diagram. Loom GRN/BLK.
HSI 3 / dual-calibration select
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Speed input or switch, 2.2 kHz max; on SM4DC dual-calibration units this is the calibration select input. Loom GRY.
Cylinder trigger -
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).
Sync trigger -
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Reluctor negative; leave unconnected with Hall sensors. Loom BLK (screened).
Output 7
Cavity: Populated
Confirmed

Autronic pin table 2016; wiring rev 3.4

Open collector, 3.5 A. Loom GRN/ORG.