Removed text is struck through; added text is highlighted.
On the 1.2 TSI/TFSI CBZA and CBZB installations described in Audi's Self-Study Programme 485, Simos 10 controls turbo charge pressure using an electric wastegate actuator and pressure and temperature signals at more than one point in the air path. This page is scoped to that documented system. Identify the actual engine, ECU and hardware before applying the same component names to another Simos 10 installation.
Control path and measurement points
The ECU calculates a nominal charge-pressure request from torque demand and adjusts charge-pressure actuator V465 to move the turbocharger wastegate. Position sensor G581 supplies actuator-position feedback. Audi describes the actuator as integral to the turbocharger assembly, with a Hall-effect position sensor; its training text states that a replacement module must be programmed using the specified guided functions. The current repair procedure for the actual vehicle and part remains authoritative.
Audi's diagram locates charge-pressure sender G31 with intake-air-temperature sender G299 in the charge-pressure pipe, upstream of the throttle. It locates manifold-pressure sender G71 with temperature sender G42 downstream, in the intake manifold and charge-air-cooler path. An ambient-pressure sender in the ECU provides a correction. The G31 signal is used to control and monitor charge pressure; G71 and G42 contribute to the calculation of air mass in the manifold. High inlet temperature can lead to a reduction in charge pressure for component protection.
These are different physical locations. A pressure difference across a partly closed throttle, or during a transient, does not by itself prove that a sensor is defective. Identify each logger channel's sensor, units and absolute or gauge reference before comparing values. At ignition on with the engine stopped and the system settled, an atmospheric reference is a useful plausibility check for relevant pressure readings, but compare against the current workshop specification and actual ambient pressure rather than a fixed universal number.
File-specific actuator-position definition lead
An independently developed OLS reader reports two separate maps in a publicly indexed V2A360ZWS74 project: ip_posn_sp_bpa_rgl_cus_pl is described as a boost-pressure actuator position setpoint for part load, and ip_posn_sp_bpa_rgl_cus_wup as a position setpoint for warm-up. The parser reports each as an eight-by-six map and labels one axis as engine speed; it does not provide a meaningful description of the other axis. The labels are present in the project, but the third-party parser’s dimensions, axes and scaling have not been independently verified in WinOLS.
These are definitions in an unidentified-source project, not proof that either map is active on the CBZA/CBZB vehicle being diagnosed, that its values match a particular ECU, or that its output is the measured G581 actuator position. Compare the ECU identification and actual operating state, request and feedback before interpreting a boost discrepancy. The Simos 10 overview records the inspected project’s hash and other limitations. Confirm provenance, rights, exact software and a verified definition before using the data.
Diagnosing a low or unstable result
Record the conditions. Capture fault codes and freeze-frame information before clearing anything. Note ECU identification, engine, gearbox, fuel, software and calibration, turbocharger and actuator part numbers, recent repairs and the conditions in which the issue appears.
Separate the request from the result. Where supported, log rpm, pedal and throttle position, requested and actual charge pressure, actuator command and reported position, upstream and manifold pressure, inlet and coolant temperatures, and intervention or fault status. A low actual pressure with a low requested pressure is a different starting point from a low actual pressure when the request remains high. The reason still needs diagnosis.
Check the air and cooling systems. Use the vehicle-specific procedure to investigate leaks or restrictions, pressure-sensor and temperature-sensor readings, and charge-cooling circuit operation. On the SSP 485 example the charge cooler has a coolant circuit; poor cooling or a misleading temperature signal can change permitted pressure. Do not defeat the temperature protection to conceal a cooling fault.
Check control and mechanical movement. Compare commanded and reported actuator position only where the diagnostic tool defines compatible units and conditions. Inspect applicable wiring, connections, actuator and linkage for faults using the current workshop test procedure. A plausible position signal does not independently prove that the valve seals correctly or that the air path is leak-free.
Verify after repair. Follow the correct guided function and adaptation procedure where required, then repeat comparable observations and review codes and relevant fuel, lambda and ignition channels. Basic settings, limits, signal direction and test conditions must be taken from the current procedure for the installed unit; do not borrow numeric adjustment values from another engine or diesel actuator.
On the documented system the electric actuator replaces the pressure-cell and N75 arrangement described for Audi's comparison engine. A generic P-code procedure for a vacuum-operated diesel actuator is not automatically the correct test for this petrol engine. A diagnostic code is a starting point and does not establish one failed component.
SEAT's CBZB control and fallback example
SEAT's Self-Study Programme 136 describes the Simos 10 1.2 TSI 77 kW example using V465 electric wastegate control without a separate N75 boost-pressure control valve or N249 turbocharger recirculation valve. These component statements describe that installation, not every 1.2 TSI engine. Verify the actual turbo and air plumbing before using a generic N75 or N249 test or assuming that either component must be added for a replacement turbocharger.
For its documented 1.2 TSI system, SEAT states that if G581 feedback fails, V465 no longer regulates the wastegate and the wastegate remains mechanically open. It describes the same open-wastegate fallback for a V465 actuator fault, with no turbo overboost produced. An open position or low pressure alone does not establish whether the fault is electrical, sensor-related, mechanical or commanded; check the fault memory, current test plan and physical system. The training text is not evidence that every failure mode or every Simos 10 calibration behaves identically.
The same programme describes a charge-pressure calculation based on accelerator position and engine speed, corrected for inlet temperature, coolant temperature and altitude, and gives a maximum of 2.1 bar absolute for its example. That number includes atmospheric pressure, is not a boost-gauge reading or a target for a modified vehicle, and is not proof of what the connected sensor or ECU requests. Compare the actual pressure target, measured values and ambient pressure using the channel definitions for the specific car. SEAT SSP 136, pages 7 and 18–21.
Replacement turbochargers and software
BTS Turbo service information SI-201208 describes specific replacement turbo and service-kit numbers for CBZA, CBZB and CBZC engines. It states that changes in the electric actuator can require a vehicle-manufacturer software action and describes an actuator fault after ignition-on as a possible indication in that replacement context. This is a supplier bulletin for the parts it names, not evidence that every fault or replacement requires the same update. Match the turbocharger and ECU to current manufacturer guidance.
A factory software update can alter the identification and calibration on which an existing tune or definition depends. Record the version before and after the authorised repair; confirm the compatible file and tool with its supplier before making any further calibration change. Do not assume an earlier tune or actuator basic setting remains appropriate after a replacement or software update.
CBZB actuator travel and adaptation example
Grup Eina's Jetta IV 1.2 TSI CBZB diagnostic bulletin describes lack of power with P334B and/or P334C, respectively identified there as actuator mechanical and adaptation faults. The provider discusses actuator-length and lower-stop adaptation, including different actions depending on the turbocharger version and whether a spacer is already installed. Its proposed spacer procedure is expressly limited to certain turbocharger suffixes and excluded for others; its procedure may also involve an ECU software update. This is a diagnostic provider's vehicle-specific example, not a general instruction to fit a spacer, reset adaptations, replace the turbo or use a particular voltage limit on every Simos 10.
For a similar complaint, retain the exact fault and freeze-frame data, turbo and actuator identification, installed spacer state and ECU software version. Check physical movement and the applicable guided test and current manufacturer repair information before changing hardware or calibration. If a software update is indicated, establish the installed tune and recovery options beforehand. An adaptation code, low charge pressure or a changed actuator voltage on its own does not establish which repair is correct.
Modified turbo and pressure-signal example
A 2018 ECUedit forum report concerns a Simos 10.2X 1.2 TSI fitted with a larger turbo, a vacuum wastegate and a separate boost controller. The owner-reported pattern is misfiring under boost with an upstream-throttle pressure sensor connected, and a change in both the misfire symptom and high-rpm lambda after disconnecting it. The engine code, software version, calibration, sensor scaling, logged channels and result were not independently verified. Neither the owner's exclusion of ignition faults nor the proposed spark-plug or fallback-pressure explanations establish the cause.
The case illustrates a testing problem: a sensor change can also change ECU calculations, mixture and fault handling, so a changed symptom does not identify the original fault or validate the tune. Do not use an unplugged sensor or higher boost as a remedy. Restore the intended sensors and control arrangement, identify the installed hardware and appropriate calibration, save faults and operating conditions, then compare verified upstream and manifold pressure channels, lambda target and measured lambda, fuel pressure, ignition and relevant interventions under repeatable, controlled conditions. Confirm pressure reference, sensor range and scaling before attributing a disagreement to a single map. Follow the vehicle-specific workshop and tool guidance, and stop load testing if the mixture or combustion is not controlled.
A replacement vacuum wastegate and external controller also differ from the factory V465/G581 arrangement described above; the report does not establish that every Simos 10 calibration supports that conversion or how factory monitoring was handled. Verify actuator control, sensor plausibility and protection strategies for the actual installation rather than borrowing settings from a different turbocharger.
Sources
Audi Self-Study Programme 485: 1.2-litre TFSI engine, English edition, air supply and engine-management sections. CBZA and CBZB application examples, V465/G581, G31/G299 and G71/G42, charge cooling, and guided-function note. Training text, not a current repair manual. Accessed 17 November 2026.
Volkswagen Self-Study Programme 443: 1.2-litre 77 kW TSI engine, French edition. CBZB and Simos 10 charge-control description. Accessed 17 November 2026.
BTS Turbo SI-201208: electric turbo actuator fault after ignition-on, German. Supplier service information restricted to the specified replacement parts and applications. Accessed 17 November 2026.
SEAT Self-Study Programme 136: 1.2-litre TSI engine, English edition, pages 7 and 18–21 (the linked host redirected to a sign-in page when checked); Spanish text rendering of the same training programme. Documented electric wastegate system, component fallbacks and absolute-pressure context; a training example, not a current repair procedure. Accessed 17 November 2026.
ECUedit forum report, 2018: Simos 10.1/2 TSI big-turbo misfires. Owner report, unverified; the shared attachment was not publicly accessible.
Open each version to inspect formatting, tables and photographs.
Revision 8: Simos 10 1.2 TSI charge pressure and wastegate diagnosis
On the 1.2 TSI/TFSI CBZA and CBZB installations described in Audi's Self-Study Programme 485, Simos 10 controls turbo charge pressure using an electric wastegate actuator and pressure and temperature signals at more than one point in the air path. This page is scoped to that documented system. Identify the actual engine, ECU and hardware before applying the same component names to another Simos 10 installation.
Control path and measurement points
The ECU calculates a nominal charge-pressure request from torque demand and adjusts charge-pressure actuator V465 to move the turbocharger wastegate. Position sensor G581 supplies actuator-position feedback. Audi describes the actuator as integral to the turbocharger assembly, with a Hall-effect position sensor; its training text states that a replacement module must be programmed using the specified guided functions. The current repair procedure for the actual vehicle and part remains authoritative.
Audi's diagram locates charge-pressure sender G31 with intake-air-temperature sender G299 in the charge-pressure pipe, upstream of the throttle. It locates manifold-pressure sender G71 with temperature sender G42 downstream, in the intake manifold and charge-air-cooler path. An ambient-pressure sender in the ECU provides a correction. The G31 signal is used to control and monitor charge pressure; G71 and G42 contribute to the calculation of air mass in the manifold. High inlet temperature can lead to a reduction in charge pressure for component protection.
These are different physical locations. A pressure difference across a partly closed throttle, or during a transient, does not by itself prove that a sensor is defective. Identify each logger channel's sensor, units and absolute or gauge reference before comparing values. At ignition on with the engine stopped and the system settled, an atmospheric reference is a useful plausibility check for relevant pressure readings, but compare against the current workshop specification and actual ambient pressure rather than a fixed universal number.
File-specific actuator-position definition lead
An independently developed OLS reader reports two separate maps in a publicly indexed V2A360ZWS74 project: ip_posn_sp_bpa_rgl_cus_pl is described as a boost-pressure actuator position setpoint for part load, and ip_posn_sp_bpa_rgl_cus_wup as a position setpoint for warm-up. The parser reports each as an eight-by-six map and labels one axis as engine speed; it does not provide a meaningful description of the other axis. The labels are present in the project, but the third-party parser’s dimensions, axes and scaling have not been independently verified in WinOLS.
These are definitions in an unidentified-source project, not proof that either map is active on the CBZA/CBZB vehicle being diagnosed, that its values match a particular ECU, or that its output is the measured G581 actuator position. Compare the ECU identification and actual operating state, request and feedback before interpreting a boost discrepancy. The Simos 10 overview records the inspected project’s hash and other limitations. Confirm provenance, rights, exact software and a verified definition before using the data.
Diagnosing a low or unstable result
- Record the conditions. Capture fault codes and freeze-frame information before clearing anything. Note ECU identification, engine, gearbox, fuel, software and calibration, turbocharger and actuator part numbers, recent repairs and the conditions in which the issue appears.
- Separate the request from the result. Where supported, log rpm, pedal and throttle position, requested and actual charge pressure, actuator command and reported position, upstream and manifold pressure, inlet and coolant temperatures, and intervention or fault status. A low actual pressure with a low requested pressure is a different starting point from a low actual pressure when the request remains high. The reason still needs diagnosis.
- Check the air and cooling systems. Use the vehicle-specific procedure to investigate leaks or restrictions, pressure-sensor and temperature-sensor readings, and charge-cooling circuit operation. On the SSP 485 example the charge cooler has a coolant circuit; poor cooling or a misleading temperature signal can change permitted pressure. Do not defeat the temperature protection to conceal a cooling fault.
- Check control and mechanical movement. Compare commanded and reported actuator position only where the diagnostic tool defines compatible units and conditions. Inspect applicable wiring, connections, actuator and linkage for faults using the current workshop test procedure. A plausible position signal does not independently prove that the valve seals correctly or that the air path is leak-free.
- Verify after repair. Follow the correct guided function and adaptation procedure where required, then repeat comparable observations and review codes and relevant fuel, lambda and ignition channels. Basic settings, limits, signal direction and test conditions must be taken from the current procedure for the installed unit; do not borrow numeric adjustment values from another engine or diesel actuator.
On the documented system the electric actuator replaces the pressure-cell and N75 arrangement described for Audi's comparison engine. A generic P-code procedure for a vacuum-operated diesel actuator is not automatically the correct test for this petrol engine. A diagnostic code is a starting point and does not establish one failed component.
SEAT's CBZB control and fallback example
SEAT's Self-Study Programme 136 describes the Simos 10 1.2 TSI 77 kW example using V465 electric wastegate control without a separate N75 boost-pressure control valve or N249 turbocharger recirculation valve. These component statements describe that installation, not every 1.2 TSI engine. Verify the actual turbo and air plumbing before using a generic N75 or N249 test or assuming that either component must be added for a replacement turbocharger.
For its documented 1.2 TSI system, SEAT states that if G581 feedback fails, V465 no longer regulates the wastegate and the wastegate remains mechanically open. It describes the same open-wastegate fallback for a V465 actuator fault, with no turbo overboost produced. An open position or low pressure alone does not establish whether the fault is electrical, sensor-related, mechanical or commanded; check the fault memory, current test plan and physical system. The training text is not evidence that every failure mode or every Simos 10 calibration behaves identically.
The same programme describes a charge-pressure calculation based on accelerator position and engine speed, corrected for inlet temperature, coolant temperature and altitude, and gives a maximum of 2.1 bar absolute for its example. That number includes atmospheric pressure, is not a boost-gauge reading or a target for a modified vehicle, and is not proof of what the connected sensor or ECU requests. Compare the actual pressure target, measured values and ambient pressure using the channel definitions for the specific car. SEAT SSP 136, pages 7 and 18–21.
Replacement turbochargers and software
BTS Turbo service information SI-201208 describes specific replacement turbo and service-kit numbers for CBZA, CBZB and CBZC engines. It states that changes in the electric actuator can require a vehicle-manufacturer software action and describes an actuator fault after ignition-on as a possible indication in that replacement context. This is a supplier bulletin for the parts it names, not evidence that every fault or replacement requires the same update. Match the turbocharger and ECU to current manufacturer guidance.
A factory software update can alter the identification and calibration on which an existing tune or definition depends. Record the version before and after the authorised repair; confirm the compatible file and tool with its supplier before making any further calibration change. Do not assume an earlier tune or actuator basic setting remains appropriate after a replacement or software update.
CBZB actuator travel and adaptation example
Grup Eina's Jetta IV 1.2 TSI CBZB diagnostic bulletin describes lack of power with P334B and/or P334C, respectively identified there as actuator mechanical and adaptation faults. The provider discusses actuator-length and lower-stop adaptation, including different actions depending on the turbocharger version and whether a spacer is already installed. Its proposed spacer procedure is expressly limited to certain turbocharger suffixes and excluded for others; its procedure may also involve an ECU software update. This is a diagnostic provider's vehicle-specific example, not a general instruction to fit a spacer, reset adaptations, replace the turbo or use a particular voltage limit on every Simos 10.
For a similar complaint, retain the exact fault and freeze-frame data, turbo and actuator identification, installed spacer state and ECU software version. Check physical movement and the applicable guided test and current manufacturer repair information before changing hardware or calibration. If a software update is indicated, establish the installed tune and recovery options beforehand. An adaptation code, low charge pressure or a changed actuator voltage on its own does not establish which repair is correct.
Modified turbo and pressure-signal example
A 2018 ECUedit forum report concerns a Simos 10.2X 1.2 TSI fitted with a larger turbo, a vacuum wastegate and a separate boost controller. The owner-reported pattern is misfiring under boost with an upstream-throttle pressure sensor connected, and a change in both the misfire symptom and high-rpm lambda after disconnecting it. The engine code, software version, calibration, sensor scaling, logged channels and result were not independently verified. Neither the owner's exclusion of ignition faults nor the proposed spark-plug or fallback-pressure explanations establish the cause.
The case illustrates a testing problem: a sensor change can also change ECU calculations, mixture and fault handling, so a changed symptom does not identify the original fault or validate the tune. Do not use an unplugged sensor or higher boost as a remedy. Restore the intended sensors and control arrangement, identify the installed hardware and appropriate calibration, save faults and operating conditions, then compare verified upstream and manifold pressure channels, lambda target and measured lambda, fuel pressure, ignition and relevant interventions under repeatable, controlled conditions. Confirm pressure reference, sensor range and scaling before attributing a disagreement to a single map. Follow the vehicle-specific workshop and tool guidance, and stop load testing if the mixture or combustion is not controlled.
A replacement vacuum wastegate and external controller also differ from the factory V465/G581 arrangement described above; the report does not establish that every Simos 10 calibration supports that conversion or how factory monitoring was handled. Verify actuator control, sensor plausibility and protection strategies for the actual installation rather than borrowing settings from a different turbocharger.
Sources
- Audi Self-Study Programme 485: 1.2-litre TFSI engine, English edition, air supply and engine-management sections. CBZA and CBZB application examples, V465/G581, G31/G299 and G71/G42, charge cooling, and guided-function note. Training text, not a current repair manual. Accessed 17 November 2026.
- Volkswagen Self-Study Programme 443: 1.2-litre 77 kW TSI engine, French edition. CBZB and Simos 10 charge-control description. Accessed 17 November 2026.
- BTS Turbo SI-201208: electric turbo actuator fault after ignition-on, German. Supplier service information restricted to the specified replacement parts and applications. Accessed 17 November 2026.
- SEAT Self-Study Programme 136: 1.2-litre TSI engine, English edition, pages 7 and 18–21 (the linked host redirected to a sign-in page when checked); Spanish text rendering of the same training programme. Documented electric wastegate system, component fallbacks and absolute-pressure context; a training example, not a current repair procedure. Accessed 17 November 2026.
- ECUedit forum report, 2018: Simos 10.1/2 TSI big-turbo misfires. Owner report, unverified; the shared attachment was not publicly accessible.
Revision 8: Simos 10 1.2 TSI charge pressure and wastegate diagnosis
On the 1.2 TSI/TFSI CBZA and CBZB installations described in Audi's Self-Study Programme 485, Simos 10 controls turbo charge pressure using an electric wastegate actuator and pressure and temperature signals at more than one point in the air path. This page is scoped to that documented system. Identify the actual engine, ECU and hardware before applying the same component names to another Simos 10 installation.
Control path and measurement points
The ECU calculates a nominal charge-pressure request from torque demand and adjusts charge-pressure actuator V465 to move the turbocharger wastegate. Position sensor G581 supplies actuator-position feedback. Audi describes the actuator as integral to the turbocharger assembly, with a Hall-effect position sensor; its training text states that a replacement module must be programmed using the specified guided functions. The current repair procedure for the actual vehicle and part remains authoritative.
Audi's diagram locates charge-pressure sender G31 with intake-air-temperature sender G299 in the charge-pressure pipe, upstream of the throttle. It locates manifold-pressure sender G71 with temperature sender G42 downstream, in the intake manifold and charge-air-cooler path. An ambient-pressure sender in the ECU provides a correction. The G31 signal is used to control and monitor charge pressure; G71 and G42 contribute to the calculation of air mass in the manifold. High inlet temperature can lead to a reduction in charge pressure for component protection.
These are different physical locations. A pressure difference across a partly closed throttle, or during a transient, does not by itself prove that a sensor is defective. Identify each logger channel's sensor, units and absolute or gauge reference before comparing values. At ignition on with the engine stopped and the system settled, an atmospheric reference is a useful plausibility check for relevant pressure readings, but compare against the current workshop specification and actual ambient pressure rather than a fixed universal number.
File-specific actuator-position definition lead
An independently developed OLS reader reports two separate maps in a publicly indexed V2A360ZWS74 project: ip_posn_sp_bpa_rgl_cus_pl is described as a boost-pressure actuator position setpoint for part load, and ip_posn_sp_bpa_rgl_cus_wup as a position setpoint for warm-up. The parser reports each as an eight-by-six map and labels one axis as engine speed; it does not provide a meaningful description of the other axis. The labels are present in the project, but the third-party parser’s dimensions, axes and scaling have not been independently verified in WinOLS.
These are definitions in an unidentified-source project, not proof that either map is active on the CBZA/CBZB vehicle being diagnosed, that its values match a particular ECU, or that its output is the measured G581 actuator position. Compare the ECU identification and actual operating state, request and feedback before interpreting a boost discrepancy. The Simos 10 overview records the inspected project’s hash and other limitations. Confirm provenance, rights, exact software and a verified definition before using the data.
Diagnosing a low or unstable result
- Record the conditions. Capture fault codes and freeze-frame information before clearing anything. Note ECU identification, engine, gearbox, fuel, software and calibration, turbocharger and actuator part numbers, recent repairs and the conditions in which the issue appears.
- Separate the request from the result. Where supported, log rpm, pedal and throttle position, requested and actual charge pressure, actuator command and reported position, upstream and manifold pressure, inlet and coolant temperatures, and intervention or fault status. A low actual pressure with a low requested pressure is a different starting point from a low actual pressure when the request remains high. The reason still needs diagnosis.
- Check the air and cooling systems. Use the vehicle-specific procedure to investigate leaks or restrictions, pressure-sensor and temperature-sensor readings, and charge-cooling circuit operation. On the SSP 485 example the charge cooler has a coolant circuit; poor cooling or a misleading temperature signal can change permitted pressure. Do not defeat the temperature protection to conceal a cooling fault.
- Check control and mechanical movement. Compare commanded and reported actuator position only where the diagnostic tool defines compatible units and conditions. Inspect applicable wiring, connections, actuator and linkage for faults using the current workshop test procedure. A plausible position signal does not independently prove that the valve seals correctly or that the air path is leak-free.
- Verify after repair. Follow the correct guided function and adaptation procedure where required, then repeat comparable observations and review codes and relevant fuel, lambda and ignition channels. Basic settings, limits, signal direction and test conditions must be taken from the current procedure for the installed unit; do not borrow numeric adjustment values from another engine or diesel actuator.
On the documented system the electric actuator replaces the pressure-cell and N75 arrangement described for Audi's comparison engine. A generic P-code procedure for a vacuum-operated diesel actuator is not automatically the correct test for this petrol engine. A diagnostic code is a starting point and does not establish one failed component.
SEAT's CBZB control and fallback example
SEAT's Self-Study Programme 136 describes the Simos 10 1.2 TSI 77 kW example using V465 electric wastegate control without a separate N75 boost-pressure control valve or N249 turbocharger recirculation valve. These component statements describe that installation, not every 1.2 TSI engine. Verify the actual turbo and air plumbing before using a generic N75 or N249 test or assuming that either component must be added for a replacement turbocharger.
For its documented 1.2 TSI system, SEAT states that if G581 feedback fails, V465 no longer regulates the wastegate and the wastegate remains mechanically open. It describes the same open-wastegate fallback for a V465 actuator fault, with no turbo overboost produced. An open position or low pressure alone does not establish whether the fault is electrical, sensor-related, mechanical or commanded; check the fault memory, current test plan and physical system. The training text is not evidence that every failure mode or every Simos 10 calibration behaves identically.
The same programme describes a charge-pressure calculation based on accelerator position and engine speed, corrected for inlet temperature, coolant temperature and altitude, and gives a maximum of 2.1 bar absolute for its example. That number includes atmospheric pressure, is not a boost-gauge reading or a target for a modified vehicle, and is not proof of what the connected sensor or ECU requests. Compare the actual pressure target, measured values and ambient pressure using the channel definitions for the specific car. SEAT SSP 136, pages 7 and 18–21.
Replacement turbochargers and software
BTS Turbo service information SI-201208 describes specific replacement turbo and service-kit numbers for CBZA, CBZB and CBZC engines. It states that changes in the electric actuator can require a vehicle-manufacturer software action and describes an actuator fault after ignition-on as a possible indication in that replacement context. This is a supplier bulletin for the parts it names, not evidence that every fault or replacement requires the same update. Match the turbocharger and ECU to current manufacturer guidance.
A factory software update can alter the identification and calibration on which an existing tune or definition depends. Record the version before and after the authorised repair; confirm the compatible file and tool with its supplier before making any further calibration change. Do not assume an earlier tune or actuator basic setting remains appropriate after a replacement or software update.
CBZB actuator travel and adaptation example
Grup Eina's Jetta IV 1.2 TSI CBZB diagnostic bulletin describes lack of power with P334B and/or P334C, respectively identified there as actuator mechanical and adaptation faults. The provider discusses actuator-length and lower-stop adaptation, including different actions depending on the turbocharger version and whether a spacer is already installed. Its proposed spacer procedure is expressly limited to certain turbocharger suffixes and excluded for others; its procedure may also involve an ECU software update. This is a diagnostic provider's vehicle-specific example, not a general instruction to fit a spacer, reset adaptations, replace the turbo or use a particular voltage limit on every Simos 10.
For a similar complaint, retain the exact fault and freeze-frame data, turbo and actuator identification, installed spacer state and ECU software version. Check physical movement and the applicable guided test and current manufacturer repair information before changing hardware or calibration. If a software update is indicated, establish the installed tune and recovery options beforehand. An adaptation code, low charge pressure or a changed actuator voltage on its own does not establish which repair is correct.
Modified turbo and pressure-signal example
A 2018 ECUedit forum report concerns a Simos 10.2X 1.2 TSI fitted with a larger turbo, a vacuum wastegate and a separate boost controller. The owner-reported pattern is misfiring under boost with an upstream-throttle pressure sensor connected, and a change in both the misfire symptom and high-rpm lambda after disconnecting it. The engine code, software version, calibration, sensor scaling, logged channels and result were not independently verified. Neither the owner's exclusion of ignition faults nor the proposed spark-plug or fallback-pressure explanations establish the cause.
The case illustrates a testing problem: a sensor change can also change ECU calculations, mixture and fault handling, so a changed symptom does not identify the original fault or validate the tune. Do not use an unplugged sensor or higher boost as a remedy. Restore the intended sensors and control arrangement, identify the installed hardware and appropriate calibration, save faults and operating conditions, then compare verified upstream and manifold pressure channels, lambda target and measured lambda, fuel pressure, ignition and relevant interventions under repeatable, controlled conditions. Confirm pressure reference, sensor range and scaling before attributing a disagreement to a single map. Follow the vehicle-specific workshop and tool guidance, and stop load testing if the mixture or combustion is not controlled.
A replacement vacuum wastegate and external controller also differ from the factory V465/G581 arrangement described above; the report does not establish that every Simos 10 calibration supports that conversion or how factory monitoring was handled. Verify actuator control, sensor plausibility and protection strategies for the actual installation rather than borrowing settings from a different turbocharger.
Sources
- Audi Self-Study Programme 485: 1.2-litre TFSI engine, English edition, air supply and engine-management sections. CBZA and CBZB application examples, V465/G581, G31/G299 and G71/G42, charge cooling, and guided-function note. Training text, not a current repair manual. Accessed 17 November 2026.
- Volkswagen Self-Study Programme 443: 1.2-litre 77 kW TSI engine, French edition. CBZB and Simos 10 charge-control description. Accessed 17 November 2026.
- BTS Turbo SI-201208: electric turbo actuator fault after ignition-on, German. Supplier service information restricted to the specified replacement parts and applications. Accessed 17 November 2026.
- SEAT Self-Study Programme 136: 1.2-litre TSI engine, English edition, pages 7 and 18–21 (the linked host redirected to a sign-in page when checked); Spanish text rendering of the same training programme. Documented electric wastegate system, component fallbacks and absolute-pressure context; a training example, not a current repair procedure. Accessed 17 November 2026.
- ECUedit forum report, 2018: Simos 10.1/2 TSI big-turbo misfires. Owner report, unverified; the shared attachment was not publicly accessible.