Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Reference
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

Changes from revision 3 to revision 4

Removed text is struck through; added text is highlighted.

Biturbo-era V6 cars share a set of commonly reported weak points and service items. The evidence is magazine features, parts-supplier listings and owner experience, so intervals and procedures must be checked against the workshop manual for the specific model.This page collects the weak points and service items commonly associated with Biturbo-era V6 cars. The information comes from magazine features, parts-supplier listings and owner experience, so intervals and procedures must be checked against the workshop manual for the specific model.

Turbochargers and oiling

The twin turbos are the main expensive risk when bearings fail. Their bearings rely on engine oil for cooling and lubrication, and the mineral oils common in the 1980s tended to burn and block oil passages. Synthetic oil was rarely used at the time. Seizures on early cars were commonly linked to switching off straight after hard driving; the engine should idle before shutting down. A banjo fitting at the rear of the engine, between the sump and flywheel, feeds the two turbo oil pipes. Leaks there are common and can look like a rear main seal failure; repair is fiddly, and care is needed not to damage the block thread. Oil feed and return condition should be checked before a turbo is condemned. No rebuild procedure or turbo part numbers have been confirmed.The twin turbos are the main expensive risk when bearings fail. Their bearings rely on engine oil for cooling and lubrication, and the mineral oils common in the 1980s tended to burn and block oil passages. Synthetic oil was rarely used at the time. Seizures on early cars were commonly linked to switching off straight after hard driving; let the engine idle before shutting down. A banjo fitting at the rear of the engine, between the sump and flywheel, feeds the two turbo oil pipes. Leaks there are common and can look like a rear main seal failure; repair is fiddly, and care is needed not to damage the block thread. Check oil feed and return condition before condemning a turbo. No rebuild procedure or turbo part numbers have been confirmed.

Fuel and ignition

Vacuum leaks are a recurring problem on injected cars of this period. The 2.5 litre cars were carburettor-fed at first and injected later; all 2.8 litre cars are injected. Later injected cars are generally regarded as the most dependable. Ignition ECU faults and poor earths are the usual electrical suspects; see the fuelling and ECU page. Loss of top-end power with a spitting or choking sound has been reported on an injected 425i after the catalyst and fuel filter were ruled out; fuel delivery at high load is the suspected cause, and no confirmed fix is known.Vacuum leaks are a recurring problem on injected cars of this period. The 2.5 litre cars were carburettor-fed at first and injected later; all 2.8 litre cars are injected. Later injected cars are generally regarded as the most dependable. Ignition ECU faults and poor earths are the usual electrical suspects; see the fuelling and ECU page. Loss of top-end power with a spitting or choking sound on an injected 425i was queried by an owner who had ruled out the catalyst and fuel filter; fuel delivery at high load is the suspected cause. No confirmed fix was found.

Timing belt, water pump and head gasket

Parts suppliers sell combined water pump, timing belt and tensioner bearing kits for the 18-valve engines. Listings give belt 311020349, tensioner bearing 311020107 and water pump 470045900, and note a newer pump design with a freeze plug. The kit should be confirmed against the car before ordering. Belt replacement intervals conflict: an enthusiast engine page advises every 25,000 miles or two years, one DIY guide suggests about 70,000 km, and a California specialist advises a much shorter interval. The manufacturer's schedule should be followed, leaning to the shorter figure, and a belt of unknown age replaced at once. A broken belt is also linked to over-revving. Head gasket replacement is a laborious job. Gasket sets for the 2.5 and 2.8 are widely available. Valve clearance is adjusted with shims and takes at least half a day. Small oil filters in the cylinder head are not designed for regular changes and can clog; a poorly routed fuel hose has caused fires.Parts suppliers sell combined water pump, timing belt and tensioner bearing kits for the 18-valve engines. Listings give belt 311020349, tensioner bearing 311020107 and water pump 470045900, and note a newer pump design with a freeze plug. Confirm against the car before ordering. Belt replacement intervals conflict: an enthusiast engine page advises every 25,000 miles or two years, one DIY guide suggests about 70,000 km, and a California specialist advises a much shorter interval. Follow the manufacturer's schedule, lean to the shorter figure, and replace a belt of unknown age at once. A broken belt is also linked to over-revving. Head gasket replacement is a laborious job. Gasket sets for the 2.5 and 2.8 are widely available. Valve clearance is adjusted with shims and takes at least half a day. Small oil filters in the cylinder head are not designed for regular changes and can clog; a poorly routed fuel hose has caused fires.

Body and mechanical weak points (early 2.5 litre car)

Rear subframe cracking, mainly on early cars, and weak differentials. The inlet plenum can crack if its bolts are over-tightened. The low-slung finned oil sump is easily damaged. Corroded connections and poor earths; rust in doors, scuttle and drain channels. A dead dashboard and switch group after bodywork usually comes from a damaged common supply wire to the centre switch panel. The starter motor is awkward to reach, and wheel bearings need regular repacking.

Diagnostics

Factory diagnostics for later cars are covered by Maserati diagnostic tools.Factory diagnostics for later cars are covered by Maserati diagnostic tools. Fault-code lists for the Weber-Marelli IAW cars, torque figures and compression specifications are not yet sourced.

Related: MABC boost control and tuning, engine specification table and service notes (including Shamal notes), engines.

Not establishedFault-code lists for the Weber-Marelli IAW cars, torque figures and compression specifications are not yet sourced.

References

Sports Car Market: Biturbo profile Old Cars Weekly: Biturbo feature Enrico's Maserati Pages: 425 questions and answers Enrico's Maserati Pages: 18-valve Biturbo engine Autodoc timing belt guide Eurospares timing belt kit Water pump and belt kit listing

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Maserati Biturbo common faults, maintenance and repair

This page collects the weak points and service items commonly associated with Biturbo-era V6 cars. The information comes from magazine features, parts-supplier listings and owner experience, so intervals and procedures must be checked against the workshop manual for the specific model.

Turbochargers and oiling

  • The twin turbos are the main expensive risk when bearings fail. Their bearings rely on engine oil for cooling and lubrication, and the mineral oils common in the 1980s tended to burn and block oil passages. Synthetic oil was rarely used at the time.
  • Seizures on early cars were commonly linked to switching off straight after hard driving; let the engine idle before shutting down.
  • A banjo fitting at the rear of the engine, between the sump and flywheel, feeds the two turbo oil pipes. Leaks there are common and can look like a rear main seal failure; repair is fiddly, and care is needed not to damage the block thread.
  • Check oil feed and return condition before condemning a turbo. No rebuild procedure or turbo part numbers have been confirmed.

Fuel and ignition

  • Vacuum leaks are a recurring problem on injected cars of this period. The 2.5 litre cars were carburettor-fed at first and injected later; all 2.8 litre cars are injected.
  • Later injected cars are generally regarded as the most dependable.
  • Ignition ECU faults and poor earths are the usual electrical suspects; see the fuelling and ECU page.
  • Loss of top-end power with a spitting or choking sound on an injected 425i was queried by an owner who had ruled out the catalyst and fuel filter; fuel delivery at high load is the suspected cause. No confirmed fix was found.

Timing belt, water pump and head gasket

  • Parts suppliers sell combined water pump, timing belt and tensioner bearing kits for the 18-valve engines. Listings give belt 311020349, tensioner bearing 311020107 and water pump 470045900, and note a newer pump design with a freeze plug. Confirm against the car before ordering.
  • Belt replacement intervals conflict: an enthusiast engine page advises every 25,000 miles or two years, one DIY guide suggests about 70,000 km, and a California specialist advises a much shorter interval. Follow the manufacturer's schedule, lean to the shorter figure, and replace a belt of unknown age at once. A broken belt is also linked to over-revving.
  • Head gasket replacement is a laborious job. Gasket sets for the 2.5 and 2.8 are widely available. Valve clearance is adjusted with shims and takes at least half a day.
  • Small oil filters in the cylinder head are not designed for regular changes and can clog; a poorly routed fuel hose has caused fires.

Body and mechanical weak points (early 2.5 litre car)

  • Rear subframe cracking, mainly on early cars, and weak differentials.
  • The inlet plenum can crack if its bolts are over-tightened.
  • The low-slung finned oil sump is easily damaged.
  • Corroded connections and poor earths; rust in doors, scuttle and drain channels. A dead dashboard and switch group after bodywork usually comes from a damaged common supply wire to the centre switch panel.
  • The starter motor is awkward to reach, and wheel bearings need regular repacking.

Diagnostics

Factory diagnostics for later cars are covered by Maserati diagnostic tools. Fault-code lists for the Weber-Marelli IAW cars, torque figures and compression specifications are not yet sourced.

Related: MABC boost control and tuning, engine specification table and service notes (including Shamal notes), engines.

References

Revision 4: Maserati Biturbo common faults, maintenance and repair

Biturbo-era V6 cars share a set of commonly reported weak points and service items. The evidence is magazine features, parts-supplier listings and owner experience, so intervals and procedures must be checked against the workshop manual for the specific model.

Turbochargers and oiling

  • The twin turbos are the main expensive risk when bearings fail. Their bearings rely on engine oil for cooling and lubrication, and the mineral oils common in the 1980s tended to burn and block oil passages. Synthetic oil was rarely used at the time.
  • Seizures on early cars were commonly linked to switching off straight after hard driving; the engine should idle before shutting down.
  • A banjo fitting at the rear of the engine, between the sump and flywheel, feeds the two turbo oil pipes. Leaks there are common and can look like a rear main seal failure; repair is fiddly, and care is needed not to damage the block thread.
  • Oil feed and return condition should be checked before a turbo is condemned. No rebuild procedure or turbo part numbers have been confirmed.

Fuel and ignition

  • Vacuum leaks are a recurring problem on injected cars of this period. The 2.5 litre cars were carburettor-fed at first and injected later; all 2.8 litre cars are injected.
  • Later injected cars are generally regarded as the most dependable.
  • Ignition ECU faults and poor earths are the usual electrical suspects; see the fuelling and ECU page.
  • Loss of top-end power with a spitting or choking sound has been reported on an injected 425i after the catalyst and fuel filter were ruled out; fuel delivery at high load is the suspected cause, and no confirmed fix is known.

Timing belt, water pump and head gasket

  • Parts suppliers sell combined water pump, timing belt and tensioner bearing kits for the 18-valve engines. Listings give belt 311020349, tensioner bearing 311020107 and water pump 470045900, and note a newer pump design with a freeze plug. The kit should be confirmed against the car before ordering.
  • Belt replacement intervals conflict: an enthusiast engine page advises every 25,000 miles or two years, one DIY guide suggests about 70,000 km, and a California specialist advises a much shorter interval. The manufacturer's schedule should be followed, leaning to the shorter figure, and a belt of unknown age replaced at once. A broken belt is also linked to over-revving.
  • Head gasket replacement is a laborious job. Gasket sets for the 2.5 and 2.8 are widely available. Valve clearance is adjusted with shims and takes at least half a day.
  • Small oil filters in the cylinder head are not designed for regular changes and can clog; a poorly routed fuel hose has caused fires.

Body and mechanical weak points (early 2.5 litre car)

  • Rear subframe cracking, mainly on early cars, and weak differentials.
  • The inlet plenum can crack if its bolts are over-tightened.
  • The low-slung finned oil sump is easily damaged.
  • Corroded connections and poor earths; rust in doors, scuttle and drain channels. A dead dashboard and switch group after bodywork usually comes from a damaged common supply wire to the centre switch panel.
  • The starter motor is awkward to reach, and wheel bearings need regular repacking.

Diagnostics

Factory diagnostics for later cars are covered by Maserati diagnostic tools.

Related: MABC boost control and tuning, engine specification table and service notes (including Shamal notes), engines.

Not established

Fault-code lists for the Weber-Marelli IAW cars, torque figures and compression specifications are not yet sourced.

References