Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Ford

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Turbomook's Ford Escort Cosworth is used on the road and at the drag strip, built around a Mark Shead 2.2-litre stroker engine and a BorgWarner S300SX FMW turbo. The owner set a 700 bhp target. A MotorWorx Dyno Dynamics sheet dated 24 September 2013 shows 667.4 hp and 563.4 lb-ft in fourth gear. Escos Gaz handled the respray. Owner's introduction and bodywork photos

Engine and transmission

The engine is a Mark Shead 2.2-litre stroker engine, paired with a Primary Designs twin-scroll T4 manifold and a BorgWarner S300SX FMW turbo. Later work added an Oppliger gear kit and cradle, a Quaife thick-wall casing and an MK Motorsport rear beam. Transmission and rear beam photos

Dyno result

The MotorWorx Dyno Dynamics sheet dated 24 September 2013, photographed and posted by the owner after mapping at MAD, shows 667.4 hp and 563.4 lb-ft in fourth gear. That is below the 700 bhp target. Update after mapping at MAD

Workshop and dyno-sheet photographs from the owner's PassionFord thread, reproduced with permission.

Sources

PassionFord build thread: introduction and bodywork photosPassionFord build thread: Mark Shead 2.2-litre stroker enginePassionFord build thread: Primary Designs twin-scroll T4 manifoldPassionFord build thread: BorgWarner S300SX FMW turboPassionFord build thread: mapping at MAD and dyno sheetPassionFord build thread: transmission and rear beam photos

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Turbomook’s 2.2-litre Ford Escort Cosworth

Turbomook's Ford Escort Cosworth is used on the road and at the drag strip, built around a Mark Shead 2.2-litre stroker engine and a BorgWarner S300SX FMW turbo. The owner set a 700 bhp target. A MotorWorx Dyno Dynamics sheet dated 24 September 2013 shows 667.4 hp and 563.4 lb-ft in fourth gear. Escos Gaz handled the respray. Owner's introduction and bodywork photos

Turbomook’s Escort in the workshop after the respray

Engine and transmission

The engine is a Mark Shead 2.2-litre stroker engine, paired with a Primary Designs twin-scroll T4 manifold and a BorgWarner S300SX FMW turbo. Later work added an Oppliger gear kit and cradle, a Quaife thick-wall casing and an MK Motorsport rear beam. Transmission and rear beam photos

Dyno result

The MotorWorx Dyno Dynamics sheet dated 24 September 2013, photographed and posted by the owner after mapping at MAD, shows 667.4 hp and 563.4 lb-ft in fourth gear. That is below the 700 bhp target. Update after mapping at MAD

MotorWorx dyno sheet showing 667.4 hp and 563.4 lb-ft

Workshop and dyno-sheet photographs from the owner's PassionFord thread, reproduced with permission.

Sources

Revision 2: Turbomook’s 2.2-litre Ford Escort Cosworth

Turbomook's Ford Escort Cosworth is used on the road and at the drag strip, built around a Mark Shead 2.2-litre stroker engine and a BorgWarner S300SX FMW turbo. The owner set a 700 bhp target. A MotorWorx Dyno Dynamics sheet dated 24 September 2013 shows 667.4 hp and 563.4 lb-ft in fourth gear. Escos Gaz handled the respray. Owner's introduction and bodywork photos

Turbomook’s Escort in the workshop after the respray

Engine and transmission

The engine is a Mark Shead 2.2-litre stroker engine, paired with a Primary Designs twin-scroll T4 manifold and a BorgWarner S300SX FMW turbo. Later work added an Oppliger gear kit and cradle, a Quaife thick-wall casing and an MK Motorsport rear beam. Transmission and rear beam photos

Dyno result

The MotorWorx Dyno Dynamics sheet dated 24 September 2013, photographed and posted by the owner after mapping at MAD, shows 667.4 hp and 563.4 lb-ft in fourth gear. That is below the 700 bhp target. Update after mapping at MAD

MotorWorx dyno sheet showing 667.4 hp and 563.4 lb-ft

Workshop and dyno-sheet photographs from the owner's PassionFord thread, reproduced with permission.

Sources