Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Abarth, Fiat

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

This is a 595 SS replica built from a classic Fiat 500 R, with a rebuilt 596.94 cc twin, a Solex 34 PBIC carburettor and a stainless replica exhaust. The cabin follows the black dashboard of a 500 L, with Jaeger instruments and a 31 cm leather steering wheel. The R’s rear engine support was still fitted when the first photographs were taken.

Engine

The owner’s engine specification gives 596.94 cc after reboring for 73.70 mm Mahle pistons. The worked head has 36 mm inlet and 30 mm exhaust valves, and the engine breathes through a Solex 34 PBIC carburettor and a stainless replica exhaust. After the carburettor was rebuilt, the owner reported a steady idle on the first short road test (owner-reported; no power figure is given).

Interior

The owner wanted the black dashboard of a 500 L and chose Jaeger instruments and a 31 cm leather steering wheel.

Photos from mikepedo on 500 Club Italia, reproduced with permission.

Sources

500 Club Italia build thread: introduction of the replica (Italian)500 Club Italia build thread: dashboard and base-car choices500 Club Italia build thread: photo update500 Club Italia build thread: carburettor rebuild and road test500 Club Italia build thread: full engine specification

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: mikepedo’s Fiat 500 R Abarth 595 SS replica

This is a 595 SS replica built from a classic Fiat 500 R, with a rebuilt 596.94 cc twin, a Solex 34 PBIC carburettor and a stainless replica exhaust. The cabin follows the black dashboard of a 500 L, with Jaeger instruments and a 31 cm leather steering wheel. The R’s rear engine support was still fitted when the first photographs were taken.

Owner’s photograph of the 595 SS replica

Engine

The owner’s engine specification gives 596.94 cc after reboring for 73.70 mm Mahle pistons. The worked head has 36 mm inlet and 30 mm exhaust valves, and the engine breathes through a Solex 34 PBIC carburettor and a stainless replica exhaust. After the carburettor was rebuilt, the owner reported a steady idle on the first short road test (owner-reported; no power figure is given).

Second view from the replica build thread

Interior

The owner wanted the black dashboard of a 500 L and chose Jaeger instruments and a 31 cm leather steering wheel.

Photos from mikepedo on 500 Club Italia, reproduced with permission.

Sources

Revision 2: mikepedo’s Fiat 500 R Abarth 595 SS replica

This is a 595 SS replica built from a classic Fiat 500 R, with a rebuilt 596.94 cc twin, a Solex 34 PBIC carburettor and a stainless replica exhaust. The cabin follows the black dashboard of a 500 L, with Jaeger instruments and a 31 cm leather steering wheel. The R’s rear engine support was still fitted when the first photographs were taken.

Owner’s photograph of the 595 SS replica

Engine

The owner’s engine specification gives 596.94 cc after reboring for 73.70 mm Mahle pistons. The worked head has 36 mm inlet and 30 mm exhaust valves, and the engine breathes through a Solex 34 PBIC carburettor and a stainless replica exhaust. After the carburettor was rebuilt, the owner reported a steady idle on the first short road test (owner-reported; no power figure is given).

Second view from the replica build thread

Interior

The owner wanted the black dashboard of a 500 L and chose Jaeger instruments and a 31 cm leather steering wheel.

Photos from mikepedo on 500 Club Italia, reproduced with permission.

Sources