Page organisation in this revision
- Page type
- Technical article
- Subject
- Modded Cars
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Saab
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
This is a manual Saab 9-3 Turbo X V6 built by Lammertse Techniek. The initial setup used a G25-660 hybrid turbo, strengthened timing chains, a twin-plate clutch and MaxxECU, and was reported by the builder at 488 hp and 613 Nm on a hub dyno. A later conversion to an EFR 8374 turbo followed, and the project title refers to 700+ hp.
Photo by Lammertse Techniek, from the original project post, reused with permission.
Engine, turbo and management
The initial setup used a G25-660 hybrid turbo machined into the original housing, strengthened timing chains, a twin-plate clutch and MaxxECU. The 488 hp and 613 Nm figures are builder-reported from a hub dyno, with the original exhaust behind a 3-inch downpipe.
Exhaust
After exhaust backpressure was measured, a 3.5-inch downpipe and midpipe were built, feeding twin exhaust branches and Magnaflow mufflers.
EFR 8374 conversion
An update dated 12 January 2026 describes an EFR 8374 turbo, custom high-flow manifolds and a fuel return system. The 700+ hp in the project title is a builder's target or claim; the configuration and results at each stage are in the source post.
Sources
Lammertse Techniek project post: complete build, dyno result and dated updates
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Lammertse Techniek Saab 9-3 Turbo X V6 build
This is a manual Saab 9-3 Turbo X V6 built by Lammertse Techniek. The initial setup used a G25-660 hybrid turbo, strengthened timing chains, a twin-plate clutch and MaxxECU, and was reported by the builder at 488 hp and 613 Nm on a hub dyno. A later conversion to an EFR 8374 turbo followed, and the project title refers to 700+ hp.

Photo by Lammertse Techniek, from the original project post, reused with permission.
Engine, turbo and management
The initial setup used a G25-660 hybrid turbo machined into the original housing, strengthened timing chains, a twin-plate clutch and MaxxECU. The 488 hp and 613 Nm figures are builder-reported from a hub dyno, with the original exhaust behind a 3-inch downpipe.
Exhaust
After exhaust backpressure was measured, a 3.5-inch downpipe and midpipe were built, feeding twin exhaust branches and Magnaflow mufflers.
EFR 8374 conversion
An update dated 12 January 2026 describes an EFR 8374 turbo, custom high-flow manifolds and a fuel return system. The 700+ hp in the project title is a builder's target or claim; the configuration and results at each stage are in the source post.
Sources
Revision 2: Lammertse Techniek Saab 9-3 Turbo X V6 build
This is a manual Saab 9-3 Turbo X V6 built by Lammertse Techniek. The initial setup used a G25-660 hybrid turbo, strengthened timing chains, a twin-plate clutch and MaxxECU, and was reported by the builder at 488 hp and 613 Nm on a hub dyno. A later conversion to an EFR 8374 turbo followed, and the project title refers to 700+ hp.

Photo by Lammertse Techniek, from the original project post, reused with permission.
Engine, turbo and management
The initial setup used a G25-660 hybrid turbo machined into the original housing, strengthened timing chains, a twin-plate clutch and MaxxECU. The 488 hp and 613 Nm figures are builder-reported from a hub dyno, with the original exhaust behind a 3-inch downpipe.
Exhaust
After exhaust backpressure was measured, a 3.5-inch downpipe and midpipe were built, feeding twin exhaust branches and Magnaflow mufflers.
EFR 8374 conversion
An update dated 12 January 2026 describes an EFR 8374 turbo, custom high-flow manifolds and a fuel return system. The 700+ hp in the project title is a builder's target or claim; the configuration and results at each stage are in the source post.
Sources