Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Reference
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

This page gathers engine data and service notes from an enthusiast reference site that photographed and documented factory engines and answered owner questions. Figures are quoted as given and sometimes differ from other sources; the differences are noted.

Engine specification table

EngineCapacity and bore × strokeValvesCompressionPowerFuelling 2.0 V6, carburettor1,996 cc, 82 × 63 mm3 per cylinder, twin overhead cams7.6–7.8:1180–210 bhpWeber DCNVH (listed as 42 DCNVH here; other sources say 36) 2.0 V6, injection1,996 cc3 per cylinder7.8:1188–220 bhpMarelli/Weber 2.5 V6, carburettor2,490.9 cc, 91.6 × 63 mm3 per cylinder7.8:1185–196 bhpWeber DCNVH 2.5 V6, injection2,490.9 cc3 per cylinder7.4 or 7.8:1185–196 bhpMarelli/Weber 2.8 V6, injection2,790 cc, 94 × 67 mm3 per cylinder7.4 or 7.8:1225–285 bhpMarelli/Weber 2.0 V6, 24 valve1,996 cc, 82 × 63 mm4 per cylinder, four cams7.4 or 7.8:1245–330 bhpMarelli/Weber 2.8 V6, 24 valve2,790 cc4 per cylinder7.4:1286 bhpMarelli/Weber Shamal 3.2 V83,212 cc, 80 × 80 mm4 per cylinder, four cams7.5:1326–370 bhpMarelli/Weber 3200 GT 3.2 V83,212 cc, 80 × 80 mm4 per cylinder8.0:1370 bhpMarelli/Weber, IHI turbos with roller bearings

All are 90° engines with two IHI turbochargers (water-cooled on later cars) and, from the Biturbo S era, two air-to-air intercoolers. Other pages give the V8 capacity as 3,217 cc; the 3200 GT is outside this wiki's era but is shown for comparison.

Design background

The 1,996 cc engine descends from the chain-driven four-cam 1,999 cc Merak V6, itself traced to the engine Giulio Alfieri designed for the Citroën SM. It evolved into a belt-driven twin-cam design with two inlet valves of different diameter (to create swirl) and one large exhaust valve per cylinder. One cam lobe operates both inlet valves. Bore and stroke changed from 80 × 66.3 mm on the Merak to 82 × 63.5 mm on the Biturbo, and three twin-choke Weber 42 DCNF carburettors gave way to one twin-choke Weber in a sealed plenum fed by two small IHI turbochargers. Block and heads are alloy with removable wet liners treated in a Nikasil-type coating. In early testing the unblown engine gave about 150 bhp; the turbo setup took it to about 180 bhp at 6,000 rpm. Engine size was kept just under two litres to avoid Italy's 38% tax band on larger engines. The Biturbo S (1983) added twin air-to-air intercoolers, water-cooled turbos and the new boost control (developed with Saab) for 205 bhp at 6,500 rpm. The 2.5 litre arrived in 1983 for export; the Biturbo i (1986) gave 188 bhp at 6,000 rpm and the Si 220 bhp at 6,350 rpm. The 2.8 litre appeared in 1987 in the 228i at 250 bhp.The 1,996 cc engine descends in principle from the chain-driven four-cam 1,999 cc Merak V6, but evolved into a belt-driven twin-cam design with two inlet valves of different diameter (to create swirl) and one large exhaust valve per cylinder. One cam lobe operates both inlet valves. Bore and stroke changed from 80 × 66.3 mm on the Merak to 82 × 63.5 mm on the Biturbo. Block and heads are alloy with removable wet liners treated in a Nikasil-type coating. In early testing the unblown engine gave about 150 bhp; two small IHI turbos and a single twin-choke Weber took it to about 180 bhp at 6,000 rpm. The Biturbo S (1983) added twin air-to-air intercoolers, water-cooled turbos and the new boost control for 205 bhp at 6,500 rpm. The 2.5 litre arrived in 1983 for export; the Biturbo i (1986) gave 188 bhp at 6,000 rpm and the Si 220 bhp at 6,350 rpm. The 2.8 litre appeared in 1987 in the 228i at 250 bhp.

2.24v technical data (24-valve 2.0, 1988–92)

ItemFigure Compression ratio7.6 ± 0.4:1 Power245 bhp at 6,200 rpm (180 kW) without catalyst; 240 bhp at 6,000 rpm with catalyst Torque223 lb-ft at 5,000 rpm without catalyst; 246 lb-ft at 3,000 rpm with catalyst Turbos / intercoolersTwo water-cooled IHI; two air-to-air FuellingElectronic fuel injection and ignition; lambda sensor and catalyst on cat cars; permanent overboost noted for the non-cat car Electrics105 amp alternator; leaded fuel on the non-catalyst car TransmissionGetrag five-speed manual, Ranger limited-slip differential, 3.77 ratio SuspensionKoni electronically adjustable (four settings), optional then standard; later used on the Shamal and Ghibli II Performance0–62 mph 5.9 s (non-cat), 6.1 s (cat); over 140 mph Weight and sizeDry 1,305 kg (cat), 1,323 kg (non-cat); wheelbase 2,514 mm; 80 litre tank

Early-car faults and their causesSeized turbochargers were commonly linked to switching off without letting the engine idle first, as the handbook directed. Broken timing belts were commonly linked to exceeding the recommended rev limit; early cars had no limiter and a recording "black box" that could void the warranty. Hard hot starting, minor electrical faults, seized turbos and rust from poor panel treatment were the other recurring complaints on 1981–84 cars.Late-model changes (UK-market notes)The 222E (1989–91) was the first coupé with the 2.8 three-valve engine, standard intercoolers and the new Weber-Marelli injection and ignition, rated 245 bhp. The Karif was a fixed-roof Spyder with power from about 224 to 286 bhp depending on specification. SE cars (1991–93) were cosmetic updates: exhausts through the rear bumper, extra fog lamps, side skirts. The 222 4v, 430 4v and later cars had the four-cam 2.8, catalysts, a foam can in place of a spare wheel, a differential oil cooler and a gearbox with a normal first-gear pattern in place of the dog-leg. The short-wheelbase Spyder kept the three-valve engine at 225 bhp because the chassis was judged unable to take the extra power. "SR" cars used the three-valve engine with the other 4v updates.

Service notes

Timing belt: the engine page advises replacement every 25,000 miles or two years, checking the oil level weekly. This is much shorter than other quoted intervals (about 70,000 km), so use the shorter interval unless the history says otherwise. The belt tensioner is adjustable; there is an oil pump pressure adjusting valve; oil passes through the water-cooled turbos. Ignition timing: no firing order or degree figures were found. Set the timing by aligning the flywheel top-dead-centre mark with the cam wheels as the manual describes, then reset the ignition timing. A carburettor car should idle smoothly even with the plenum removed; rough idle then points to a partly blocked idle jet. Plenum and carburettor hose routing on the later progressive 425 carburettor is poorly documented in the common manuals. Window winder cables fail when gummed with grease; clean and reassemble dry.Timing belt: the engine page advises replacement every 25,000 miles or two years, checking the oil level weekly. This is much shorter than other quoted intervals (about 70,000 km), so use the shorter interval unless the history says otherwise. The belt tensioner is adjustable; there is an oil pump pressure adjusting valve; oil passes through the water-cooled turbos. Firing order, ignition timing: set the timing by aligning the flywheel top-dead-centre mark with the cam wheels as the manual describes, then reset the ignition timing. A carburettor car should idle smoothly even with the plenum removed; rough idle then points to a partly blocked idle jet. Plenum and carburettor hose routing on the later progressive 425 carburettor is poorly documented in the common manuals. Window winder cables fail when gummed with grease; clean and reassemble dry.

Shamal notes

No design fault is noted for the V8, although the crankshaft was changed when the later V8s were made. Check for accident damage, differential wear (the Biturbo-type axle is retained; later cars have a differential oil cooler), leaking radiators and alternators that fail to charge. Change the cam belt unless a recent change is documented. Ghibli GT 17-inch wheels do not fit because the stud pattern differs slightly, though they can look as if they do. A factory SD tester is recommended for a recurring engine warning light; faulty lambda probes and connectors are simple causes. Speedometer faults trace to the instrument connectors or the sensor on the differential. One rich-running case with black plugs, hard hot starting and smoke from all exhausts followed a belt change and sensor replacement; confirm timing and the cylinder bank firing sequence after any belt work. Boost gauge behaviour is subjective, but a Shamal should consistently reach the start of the yellow band; check wastegate pre-load if it does not. Master cylinder rebuild kits are poor; pressure bleeding avoids damaging worn bore areas.

References

Enrico's Maserati Pages: Biturbo engines 1981–2001 Enrico's Maserati Pages: 18-valve Biturbo engine Enrico's Maserati Pages: the Biturbo years Enrico's Maserati Pages: Biturbo models on the UK market Enrico's Maserati Pages: 2.24v Enrico's Maserati Pages: Shamal enquiriesEnrico's Maserati Pages: Biturbo engines 1981–2001 Enrico's Maserati Pages: 18-valve Biturbo engine Enrico's Maserati Pages: 2.24v Enrico's Maserati Pages: Shamal enquiries

Back to the Maserati Biturbo hub.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Maserati Biturbo engine specification table and service notes

This page gathers engine data and service notes from an enthusiast reference site that photographed and documented factory engines and answered owner questions. Figures are quoted as given and sometimes differ from other sources; the differences are noted.

Engine specification table

EngineCapacity and bore × strokeValvesCompressionPowerFuelling
2.0 V6, carburettor1,996 cc, 82 × 63 mm3 per cylinder, twin overhead cams7.6–7.8:1180–210 bhpWeber DCNVH (listed as 42 DCNVH here; other sources say 36)
2.0 V6, injection1,996 cc3 per cylinder7.8:1188–220 bhpMarelli/Weber
2.5 V6, carburettor2,490.9 cc, 91.6 × 63 mm3 per cylinder7.8:1185–196 bhpWeber DCNVH
2.5 V6, injection2,490.9 cc3 per cylinder7.4 or 7.8:1185–196 bhpMarelli/Weber
2.8 V6, injection2,790 cc, 94 × 67 mm3 per cylinder7.4 or 7.8:1225–285 bhpMarelli/Weber
2.0 V6, 24 valve1,996 cc, 82 × 63 mm4 per cylinder, four cams7.4 or 7.8:1245–330 bhpMarelli/Weber
2.8 V6, 24 valve2,790 cc4 per cylinder7.4:1286 bhpMarelli/Weber
Shamal 3.2 V83,212 cc, 80 × 80 mm4 per cylinder, four cams7.5:1326–370 bhpMarelli/Weber
3200 GT 3.2 V83,212 cc, 80 × 80 mm4 per cylinder8.0:1370 bhpMarelli/Weber, IHI turbos with roller bearings

All are 90° engines with two IHI turbochargers (water-cooled on later cars) and, from the Biturbo S era, two air-to-air intercoolers. Other pages give the V8 capacity as 3,217 cc; the 3200 GT is outside this wiki's era but is shown for comparison.

Design background

  • The 1,996 cc engine descends in principle from the chain-driven four-cam 1,999 cc Merak V6, but evolved into a belt-driven twin-cam design with two inlet valves of different diameter (to create swirl) and one large exhaust valve per cylinder. One cam lobe operates both inlet valves.
  • Bore and stroke changed from 80 × 66.3 mm on the Merak to 82 × 63.5 mm on the Biturbo.
  • Block and heads are alloy with removable wet liners treated in a Nikasil-type coating.
  • In early testing the unblown engine gave about 150 bhp; two small IHI turbos and a single twin-choke Weber took it to about 180 bhp at 6,000 rpm.
  • The Biturbo S (1983) added twin air-to-air intercoolers, water-cooled turbos and the new boost control for 205 bhp at 6,500 rpm. The 2.5 litre arrived in 1983 for export; the Biturbo i (1986) gave 188 bhp at 6,000 rpm and the Si 220 bhp at 6,350 rpm. The 2.8 litre appeared in 1987 in the 228i at 250 bhp.

2.24v technical data (24-valve 2.0, 1988–92)

ItemFigure
Compression ratio7.6 ± 0.4:1
Power245 bhp at 6,200 rpm (180 kW) without catalyst; 240 bhp at 6,000 rpm with catalyst
Torque223 lb-ft at 5,000 rpm without catalyst; 246 lb-ft at 3,000 rpm with catalyst
Turbos / intercoolersTwo water-cooled IHI; two air-to-air
FuellingElectronic fuel injection and ignition; lambda sensor and catalyst on cat cars; permanent overboost noted for the non-cat car
Electrics105 amp alternator; leaded fuel on the non-catalyst car
TransmissionGetrag five-speed manual, Ranger limited-slip differential, 3.77 ratio
SuspensionKoni electronically adjustable (four settings), optional then standard; later used on the Shamal and Ghibli II
Performance0–62 mph 5.9 s (non-cat), 6.1 s (cat); over 140 mph
Weight and sizeDry 1,305 kg (cat), 1,323 kg (non-cat); wheelbase 2,514 mm; 80 litre tank

Service notes

  • Timing belt: the engine page advises replacement every 25,000 miles or two years, checking the oil level weekly. This is much shorter than other quoted intervals (about 70,000 km), so use the shorter interval unless the history says otherwise.
  • The belt tensioner is adjustable; there is an oil pump pressure adjusting valve; oil passes through the water-cooled turbos.
  • Firing order, ignition timing: set the timing by aligning the flywheel top-dead-centre mark with the cam wheels as the manual describes, then reset the ignition timing. A carburettor car should idle smoothly even with the plenum removed; rough idle then points to a partly blocked idle jet.
  • Plenum and carburettor hose routing on the later progressive 425 carburettor is poorly documented in the common manuals.
  • Window winder cables fail when gummed with grease; clean and reassemble dry.

Shamal notes

  • No design fault is noted for the V8, although the crankshaft was changed when the later V8s were made.
  • Check for accident damage, differential wear (the Biturbo-type axle is retained; later cars have a differential oil cooler), leaking radiators and alternators that fail to charge. Change the cam belt unless a recent change is documented.
  • Ghibli GT 17-inch wheels do not fit because the stud pattern differs slightly, though they can look as if they do.
  • A factory SD tester is recommended for a recurring engine warning light; faulty lambda probes and connectors are simple causes. Speedometer faults trace to the instrument connectors or the sensor on the differential.
  • One rich-running case with black plugs, hard hot starting and smoke from all exhausts followed a belt change and sensor replacement; confirm timing and the cylinder bank firing sequence after any belt work.
  • Boost gauge behaviour is subjective, but a Shamal should consistently reach the start of the yellow band; check wastegate pre-load if it does not.
  • Master cylinder rebuild kits are poor; pressure bleeding avoids damaging worn bore areas.

References

Back to the Maserati Biturbo hub.

Revision 2: Maserati Biturbo engine specification table and service notes

This page gathers engine data and service notes from an enthusiast reference site that photographed and documented factory engines and answered owner questions. Figures are quoted as given and sometimes differ from other sources; the differences are noted.

Engine specification table

EngineCapacity and bore × strokeValvesCompressionPowerFuelling
2.0 V6, carburettor1,996 cc, 82 × 63 mm3 per cylinder, twin overhead cams7.6–7.8:1180–210 bhpWeber DCNVH (listed as 42 DCNVH here; other sources say 36)
2.0 V6, injection1,996 cc3 per cylinder7.8:1188–220 bhpMarelli/Weber
2.5 V6, carburettor2,490.9 cc, 91.6 × 63 mm3 per cylinder7.8:1185–196 bhpWeber DCNVH
2.5 V6, injection2,490.9 cc3 per cylinder7.4 or 7.8:1185–196 bhpMarelli/Weber
2.8 V6, injection2,790 cc, 94 × 67 mm3 per cylinder7.4 or 7.8:1225–285 bhpMarelli/Weber
2.0 V6, 24 valve1,996 cc, 82 × 63 mm4 per cylinder, four cams7.4 or 7.8:1245–330 bhpMarelli/Weber
2.8 V6, 24 valve2,790 cc4 per cylinder7.4:1286 bhpMarelli/Weber
Shamal 3.2 V83,212 cc, 80 × 80 mm4 per cylinder, four cams7.5:1326–370 bhpMarelli/Weber
3200 GT 3.2 V83,212 cc, 80 × 80 mm4 per cylinder8.0:1370 bhpMarelli/Weber, IHI turbos with roller bearings

All are 90° engines with two IHI turbochargers (water-cooled on later cars) and, from the Biturbo S era, two air-to-air intercoolers. Other pages give the V8 capacity as 3,217 cc; the 3200 GT is outside this wiki's era but is shown for comparison.

Design background

  • The 1,996 cc engine descends from the chain-driven four-cam 1,999 cc Merak V6, itself traced to the engine Giulio Alfieri designed for the Citroën SM. It evolved into a belt-driven twin-cam design with two inlet valves of different diameter (to create swirl) and one large exhaust valve per cylinder. One cam lobe operates both inlet valves.
  • Bore and stroke changed from 80 × 66.3 mm on the Merak to 82 × 63.5 mm on the Biturbo, and three twin-choke Weber 42 DCNF carburettors gave way to one twin-choke Weber in a sealed plenum fed by two small IHI turbochargers.
  • Block and heads are alloy with removable wet liners treated in a Nikasil-type coating.
  • In early testing the unblown engine gave about 150 bhp; the turbo setup took it to about 180 bhp at 6,000 rpm. Engine size was kept just under two litres to avoid Italy's 38% tax band on larger engines.
  • The Biturbo S (1983) added twin air-to-air intercoolers, water-cooled turbos and the new boost control (developed with Saab) for 205 bhp at 6,500 rpm. The 2.5 litre arrived in 1983 for export; the Biturbo i (1986) gave 188 bhp at 6,000 rpm and the Si 220 bhp at 6,350 rpm. The 2.8 litre appeared in 1987 in the 228i at 250 bhp.

2.24v technical data (24-valve 2.0, 1988–92)

ItemFigure
Compression ratio7.6 ± 0.4:1
Power245 bhp at 6,200 rpm (180 kW) without catalyst; 240 bhp at 6,000 rpm with catalyst
Torque223 lb-ft at 5,000 rpm without catalyst; 246 lb-ft at 3,000 rpm with catalyst
Turbos / intercoolersTwo water-cooled IHI; two air-to-air
FuellingElectronic fuel injection and ignition; lambda sensor and catalyst on cat cars; permanent overboost noted for the non-cat car
Electrics105 amp alternator; leaded fuel on the non-catalyst car
TransmissionGetrag five-speed manual, Ranger limited-slip differential, 3.77 ratio
SuspensionKoni electronically adjustable (four settings), optional then standard; later used on the Shamal and Ghibli II
Performance0–62 mph 5.9 s (non-cat), 6.1 s (cat); over 140 mph
Weight and sizeDry 1,305 kg (cat), 1,323 kg (non-cat); wheelbase 2,514 mm; 80 litre tank

Early-car faults and their causes

  • Seized turbochargers were commonly linked to switching off without letting the engine idle first, as the handbook directed.
  • Broken timing belts were commonly linked to exceeding the recommended rev limit; early cars had no limiter and a recording "black box" that could void the warranty.
  • Hard hot starting, minor electrical faults, seized turbos and rust from poor panel treatment were the other recurring complaints on 1981–84 cars.

Late-model changes (UK-market notes)

  • The 222E (1989–91) was the first coupé with the 2.8 three-valve engine, standard intercoolers and the new Weber-Marelli injection and ignition, rated 245 bhp.
  • The Karif was a fixed-roof Spyder with power from about 224 to 286 bhp depending on specification.
  • SE cars (1991–93) were cosmetic updates: exhausts through the rear bumper, extra fog lamps, side skirts.
  • The 222 4v, 430 4v and later cars had the four-cam 2.8, catalysts, a foam can in place of a spare wheel, a differential oil cooler and a gearbox with a normal first-gear pattern in place of the dog-leg. The short-wheelbase Spyder kept the three-valve engine at 225 bhp because the chassis was judged unable to take the extra power. "SR" cars used the three-valve engine with the other 4v updates.

Service notes

  • Timing belt: the engine page advises replacement every 25,000 miles or two years, checking the oil level weekly. This is much shorter than other quoted intervals (about 70,000 km), so use the shorter interval unless the history says otherwise.
  • The belt tensioner is adjustable; there is an oil pump pressure adjusting valve; oil passes through the water-cooled turbos.
  • Ignition timing: no firing order or degree figures were found. Set the timing by aligning the flywheel top-dead-centre mark with the cam wheels as the manual describes, then reset the ignition timing. A carburettor car should idle smoothly even with the plenum removed; rough idle then points to a partly blocked idle jet.
  • Plenum and carburettor hose routing on the later progressive 425 carburettor is poorly documented in the common manuals.
  • Window winder cables fail when gummed with grease; clean and reassemble dry.

Shamal notes

  • No design fault is noted for the V8, although the crankshaft was changed when the later V8s were made.
  • Check for accident damage, differential wear (the Biturbo-type axle is retained; later cars have a differential oil cooler), leaking radiators and alternators that fail to charge. Change the cam belt unless a recent change is documented.
  • Ghibli GT 17-inch wheels do not fit because the stud pattern differs slightly, though they can look as if they do.
  • A factory SD tester is recommended for a recurring engine warning light; faulty lambda probes and connectors are simple causes. Speedometer faults trace to the instrument connectors or the sensor on the differential.
  • One rich-running case with black plugs, hard hot starting and smoke from all exhausts followed a belt change and sensor replacement; confirm timing and the cylinder bank firing sequence after any belt work.
  • Boost gauge behaviour is subjective, but a Shamal should consistently reach the start of the yellow band; check wastegate pre-load if it does not.
  • Master cylinder rebuild kits are poor; pressure bleeding avoids damaging worn bore areas.

References

Back to the Maserati Biturbo hub.