This page gathers engine data and service notes from an enthusiast reference site that photographed and documented factory engines and answered owner questions. Figures are quoted as given and sometimes differ from other sources; the differences are noted.
Engine specification table
| Engine | Capacity and bore × stroke | Valves | Compression | Power | Fuelling |
|---|---|---|---|---|---|
| 2.0 V6, carburettor | 1,996 cc, 82 × 63 mm | 3 per cylinder, twin overhead cams | 7.6–7.8:1 | 180–210 bhp | Weber DCNVH (listed as 42 DCNVH here; other sources say 36) |
| 2.0 V6, injection | 1,996 cc | 3 per cylinder | 7.8:1 | 188–220 bhp | Marelli/Weber |
| 2.5 V6, carburettor | 2,490.9 cc, 91.6 × 63 mm | 3 per cylinder | 7.8:1 | 185–196 bhp | Weber DCNVH |
| 2.5 V6, injection | 2,490.9 cc | 3 per cylinder | 7.4 or 7.8:1 | 185–196 bhp | Marelli/Weber |
| 2.8 V6, injection | 2,790 cc, 94 × 67 mm | 3 per cylinder | 7.4 or 7.8:1 | 225–285 bhp | Marelli/Weber |
| 2.0 V6, 24 valve | 1,996 cc, 82 × 63 mm | 4 per cylinder, four cams | 7.4 or 7.8:1 | 245–330 bhp | Marelli/Weber |
| 2.8 V6, 24 valve | 2,790 cc | 4 per cylinder | 7.4:1 | 286 bhp | Marelli/Weber |
| Shamal 3.2 V8 | 3,212 cc, 80 × 80 mm | 4 per cylinder, four cams | 7.5:1 | 326–370 bhp | Marelli/Weber |
| 3200 GT 3.2 V8 | 3,212 cc, 80 × 80 mm | 4 per cylinder | 8.0:1 | 370 bhp | Marelli/Weber, IHI turbos with roller bearings |
All are 90° engines with two IHI turbochargers (water-cooled on later cars) and, from the Biturbo S era, two air-to-air intercoolers. Other pages give the V8 capacity as 3,217 cc; the 3200 GT is outside this wiki's era but is shown for comparison.
Design background
- The 1,996 cc engine descends in principle from the chain-driven four-cam 1,999 cc Merak V6, but evolved into a belt-driven twin-cam design with two inlet valves of different diameter (to create swirl) and one large exhaust valve per cylinder. One cam lobe operates both inlet valves.
- Bore and stroke changed from 80 × 66.3 mm on the Merak to 82 × 63.5 mm on the Biturbo.
- Block and heads are alloy with removable wet liners treated in a Nikasil-type coating.
- In early testing the unblown engine gave about 150 bhp; two small IHI turbos and a single twin-choke Weber took it to about 180 bhp at 6,000 rpm.
- The Biturbo S (1983) added twin air-to-air intercoolers, water-cooled turbos and the new boost control for 205 bhp at 6,500 rpm. The 2.5 litre arrived in 1983 for export; the Biturbo i (1986) gave 188 bhp at 6,000 rpm and the Si 220 bhp at 6,350 rpm. The 2.8 litre appeared in 1987 in the 228i at 250 bhp.
2.24v technical data (24-valve 2.0, 1988–92)
| Item | Figure |
|---|---|
| Compression ratio | 7.6 ± 0.4:1 |
| Power | 245 bhp at 6,200 rpm (180 kW) without catalyst; 240 bhp at 6,000 rpm with catalyst |
| Torque | 223 lb-ft at 5,000 rpm without catalyst; 246 lb-ft at 3,000 rpm with catalyst |
| Turbos / intercoolers | Two water-cooled IHI; two air-to-air |
| Fuelling | Electronic fuel injection and ignition; lambda sensor and catalyst on cat cars; permanent overboost noted for the non-cat car |
| Electrics | 105 amp alternator; leaded fuel on the non-catalyst car |
| Transmission | Getrag five-speed manual, Ranger limited-slip differential, 3.77 ratio |
| Suspension | Koni electronically adjustable (four settings), optional then standard; later used on the Shamal and Ghibli II |
| Performance | 0–62 mph 5.9 s (non-cat), 6.1 s (cat); over 140 mph |
| Weight and size | Dry 1,305 kg (cat), 1,323 kg (non-cat); wheelbase 2,514 mm; 80 litre tank |
Service notes
- Timing belt: the engine page advises replacement every 25,000 miles or two years, checking the oil level weekly. This is much shorter than other quoted intervals (about 70,000 km), so use the shorter interval unless the history says otherwise.
- The belt tensioner is adjustable; there is an oil pump pressure adjusting valve; oil passes through the water-cooled turbos.
- Firing order, ignition timing: set the timing by aligning the flywheel top-dead-centre mark with the cam wheels as the manual describes, then reset the ignition timing. A carburettor car should idle smoothly even with the plenum removed; rough idle then points to a partly blocked idle jet.
- Plenum and carburettor hose routing on the later progressive 425 carburettor is poorly documented in the common manuals.
- Window winder cables fail when gummed with grease; clean and reassemble dry.
Shamal notes
- No design fault is noted for the V8, although the crankshaft was changed when the later V8s were made.
- Check for accident damage, differential wear (the Biturbo-type axle is retained; later cars have a differential oil cooler), leaking radiators and alternators that fail to charge. Change the cam belt unless a recent change is documented.
- Ghibli GT 17-inch wheels do not fit because the stud pattern differs slightly, though they can look as if they do.
- A factory SD tester is recommended for a recurring engine warning light; faulty lambda probes and connectors are simple causes. Speedometer faults trace to the instrument connectors or the sensor on the differential.
- One rich-running case with black plugs, hard hot starting and smoke from all exhausts followed a belt change and sensor replacement; confirm timing and the cylinder bank firing sequence after any belt work.
- Boost gauge behaviour is subjective, but a Shamal should consistently reach the start of the yellow band; check wastegate pre-load if it does not.
- Master cylinder rebuild kits are poor; pressure bleeding avoids damaging worn bore areas.
References
- Enrico's Maserati Pages: Biturbo engines 1981–2001
- Enrico's Maserati Pages: 18-valve Biturbo engine
- Enrico's Maserati Pages: 2.24v
- Enrico's Maserati Pages: Shamal enquiries
Back to the Maserati Biturbo hub.