Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

This page explains how Biturbo boost is controlled and the approaches used to change it. Most of the practical information comes from owner experience on one carburettor 425 and related enquiries, not from factory data, so treat it as a starting point. Raising boost without checking fuelling and ignition can destroy the engine. No dyno-verified results are available, so none are given.

Before MABC: direct wastegate control

The earliest cars opened the wastegates by feeding compressor pressure straight to the actuator diaphragm. They also had no rev limiter; a "black box" simply recorded when the recommended engine speed had been exceeded, which affected the warranty.

How MABC works

  • Introduced from 1983 on the Biturbo S (dated 1984 in some entries). It has four parts: a knock sensor mounted over the cam cover, an intake pressure transducer (a pressure-sensitive variable resistor), the control unit, and a solenoid valve that varies the pressure sent to the wastegate actuators.
  • The solenoid (often called the AMAL valve) has three ports: C receives turbo pressure, W carries it to the wastegates, and R vents it away. The control unit switches the valve with pulses of varying width; more air reaching the actuators means less boost.
  • At idle and in gentle driving the unit sits in a default duty cycle that allows over-boost; as pressure and engine speed rise it switches to active control, lets boost peak briefly and settles it to a steady value.
  • It is closely related to Saab's Automatic Performance Control; the control unit on carburettor cars carries three trim potentiometers: P (default duty cycle, effectively peak boost), F (full-boost limit against engine speed) and K (knock sensitivity).
  • The unit on carburettor cars (pre-1989) is a black plastic box under the carpet near the driver's right foot, with the three adjusters under a sealed cover.
  • Injected cars use the Weber-Marelli system to control ignition, injection and boost from stored map data, so there are no adjusters; separate ignition and injection control units are reported on the Si.
  • Standard boost on the carburettor 2.5 is quoted at about 10 psi; the gauge normally reaches the first yellow band on a healthy car. A 2.5 is also quoted at a maximum of 11 psi, and a development figure of 0.8 bar appears elsewhere.

Checks before raising boost

  • MABC working correctly; distributor vacuum advance chambers and their linkage intact; static ignition timing correct; valve clearances set so the cam boxes are quiet.
  • A correct or slightly rich mixture. A lean mixture at higher boost sharply raises exhaust gas temperature and can wreck the engine.
  • Inlet temperature under control: intercooling and water injection address both exhaust and inlet temperature.

Common ways boost is raised

  • Bleeding the wastegate line. A bleed valve in the W pipe, a small hole in the T-piece where the W pipe splits, or a change to the restrictors in the valve legs (remove the R restrictor, fit a smaller C restrictor or a W restrictor) reduces air to the actuators. It is simple and crude, and the restrictor method is trial and error. Disconnecting the W pipe altogether gives the maximum the turbos can make.
  • Shorting the transducer. Bypassing it holds the controller in its default over-boost cycle; about 15 psi, roughly half as much again as standard, was reported on an intercooled car with water injection.
  • Modifying the controller. On one carburettor car the F circuitry was removed, a resistor changed, a link wire added and the P potentiometer replaced by a dashboard-mounted control, so the unit still protects against overspeed and knock while the driver sets the maximum. Mark original potentiometer positions before touching them.
  • Electronic boost controller with a wideband lambda sensor for mixture monitoring.
  • Injected cars: a reprogrammed chip is suggested, otherwise the line-bleed methods apply. A US owner of an Si also planned to remove the air pump and catalyst, expecting about 10–15 hp from that alone.

Supporting changes

  • Intercoolers: modified air-to-air units with ducting from the grille took 100°C compressed air to about 28°C at 25°C ambient (5,500 rpm, third gear). They need airflow, so they do little below about 40 mph.
  • Water injection: a pump and solenoid supplying two small orifices on the plenum, switching on above 10 psi at about 300 ml/min, was used to suppress pinking. It works at all speeds, complementing the intercoolers. The plenum was modified by an aluminium welding specialist.
  • Pop-off valve on the plenum to stop pressure returning to the turbos when the throttle closes.
  • Monitoring: thermocouples in the turbo-to-intercooler pipe, the No. 6 exhaust manifold and the No. 6 intake manifold.
  • If intercoolers are fitted to a carburettor car, re-jetting for the denser charge is suggested. No jet sizes are available.
  • Further steps mentioned: advancing ignition, octane boosters, adding methanol to the water.

Diagnosing low or no boost

  • Wastegates should be closed with the engine off. A gate seized closed gives very high boost; seized open gives almost none. Check spring tension, then use an air line to see that each gate opens and closes. The valve seat can also crack from heat and let boost leak away.
  • A poor connector at the knock sensor over the right-hand cam cover is a more usual cause of boost cut-back than the sensor itself. Valves would have to be very tight to reduce boost.
  • Leaks at the exhaust-to-turbo joint, and swapped boost lines on a previously modified car, are other causes.
  • A leak of oil at the rear of the engine often comes from the banjo fitting between the sump and flywheel feeding the turbo oil lines.

Cautions

  • Turbochargers are the main failure concern; see common faults and repair.
  • Output differs by market and catalyst fitment, so measure a baseline power run before making changes.

Related: fuelling and ECU, ignition and standalone conversion notes, engines.

References