Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Renault Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Alpine, Renault

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Scope

Renix engine management was fitted to 1980s Renault petrol injection cars including the V6 turbo Renault 25 and the Alpine GTA. The technical notes below come from one enthusiast's published reverse-engineering of the early "Renix 1" unit; they have not been independently verified, and the original page is the only source. They are useful as a map of where calibration data lives, not as a tuning procedure. For the diesel and Sagem-era controllers see Sagem and Renault engine ECU families.

Hardware

The calibration lives in a 512-byte N82S147F PROM. It is fused and cannot be erased, and the part is no longer made. It can be read by desoldering it, and a converter board lets a rewritable 27128A EPROM take its place. The microcontroller is an EF6801U4PV with its firmware in internal ROM, read in test mode. The common version is S100723008A; a rare S100723008B has masked internal ROM. The R25 Turbo ECU uses the same board with different component values and firmware (S100723003). Later units add throttle potentiometers and better algorithms. A rare 1988 to 1992 GTA catalyst ECU (S101100108A) uses an MC68HC11 whose code is read and write protected. Later Safrane and Laguna 3.0 units are reported to be tamper-protected.

Calibrations and table addresses

Known original calibrations, earliest first, are 111B, 111F, 112F, 211D, 311, 501, 601 and 611, identified by a sticker on the PROM. The aftermarket tuner BBR's second fuel map is said to match factory 601B.

AddressContent 002h / 004hVersion number and calibration revision 005hIgnition base map, 9 rows by 13 columns 07AhFuel base map, 9 rows by 13 columns 0EFhCoolant temperature fuelling correction, 9 by 1 125hBattery voltage correction, 9 by 1 14Eh to 151hValues differ between the standard ECU (5C) and R25 Turbo (52)

Speed breakpoints run from 650 to 6,000 rpm and manifold pressure from about -13 to 14 psi. Several addresses (1FFh, 1E0h to 1E1h, 1E6h to 1E7h) are unresolved.

Limits that matter for boost

The Renix 1 only sees the throttle as closed, mid or fully open, so it cannot adjust fuelling for airflow changes at a constant manifold pressure. Fuelling can differ with throttle position at the same boost. The standard rev limit is about 6,200 rpm, and the author describes work to raise it to about 6,800 rpm. Defeating the factory boost limit is attributed to a board modification with a 4.7 V zener diode, but the stock board is not modified in the author's unit, so this is reported rather than demonstrated. A wastegate bleed valve is said to be the main change in a typical upgrade.

Not established

The purpose of several addresses, any verified boost-limit modification, and the cars outside the GTA and 25 Turbo that share these calibrations.

Sources

Renault Alpine forum: Renix ECU PROM dump and calibration notes, accessed 2026-11-19. RTOC: RTuner manual, listed in search results, not read.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Renix engine management on the Renault 25 Turbo and Alpine GTA

Scope

Renix engine management was fitted to 1980s Renault petrol injection cars including the V6 turbo Renault 25 and the Alpine GTA. The technical notes below come from one enthusiast's published reverse-engineering of the early "Renix 1" unit; they have not been independently verified, and the original page is the only source. They are useful as a map of where calibration data lives, not as a tuning procedure. For the diesel and Sagem-era controllers see Sagem and Renault engine ECU families.

Hardware

  • The calibration lives in a 512-byte N82S147F PROM. It is fused and cannot be erased, and the part is no longer made. It can be read by desoldering it, and a converter board lets a rewritable 27128A EPROM take its place.
  • The microcontroller is an EF6801U4PV with its firmware in internal ROM, read in test mode. The common version is S100723008A; a rare S100723008B has masked internal ROM.
  • The R25 Turbo ECU uses the same board with different component values and firmware (S100723003).
  • Later units add throttle potentiometers and better algorithms. A rare 1988 to 1992 GTA catalyst ECU (S101100108A) uses an MC68HC11 whose code is read and write protected. Later Safrane and Laguna 3.0 units are reported to be tamper-protected.

Calibrations and table addresses

Known original calibrations, earliest first, are 111B, 111F, 112F, 211D, 311, 501, 601 and 611, identified by a sticker on the PROM. The aftermarket tuner BBR's second fuel map is said to match factory 601B.

AddressContent
002h / 004hVersion number and calibration revision
005hIgnition base map, 9 rows by 13 columns
07AhFuel base map, 9 rows by 13 columns
0EFhCoolant temperature fuelling correction, 9 by 1
125hBattery voltage correction, 9 by 1
14Eh to 151hValues differ between the standard ECU (5C) and R25 Turbo (52)

Speed breakpoints run from 650 to 6,000 rpm and manifold pressure from about -13 to 14 psi. Several addresses (1FFh, 1E0h to 1E1h, 1E6h to 1E7h) are unresolved.

Limits that matter for boost

  • The Renix 1 only sees the throttle as closed, mid or fully open, so it cannot adjust fuelling for airflow changes at a constant manifold pressure. Fuelling can differ with throttle position at the same boost.
  • The standard rev limit is about 6,200 rpm, and the author describes work to raise it to about 6,800 rpm.
  • Defeating the factory boost limit is attributed to a board modification with a 4.7 V zener diode, but the stock board is not modified in the author's unit, so this is reported rather than demonstrated. A wastegate bleed valve is said to be the main change in a typical upgrade.

Not established

The purpose of several addresses, any verified boost-limit modification, and the cars outside the GTA and 25 Turbo that share these calibrations.

Sources

Revision 1: Renix engine management on the Renault 25 Turbo and Alpine GTA

Scope

Renix engine management was fitted to 1980s Renault petrol injection cars including the V6 turbo Renault 25 and the Alpine GTA. The technical notes below come from one enthusiast's published reverse-engineering of the early "Renix 1" unit; they have not been independently verified, and the original page is the only source. They are useful as a map of where calibration data lives, not as a tuning procedure. For the diesel and Sagem-era controllers see Sagem and Renault engine ECU families.

Hardware

  • The calibration lives in a 512-byte N82S147F PROM. It is fused and cannot be erased, and the part is no longer made. It can be read by desoldering it, and a converter board lets a rewritable 27128A EPROM take its place.
  • The microcontroller is an EF6801U4PV with its firmware in internal ROM, read in test mode. The common version is S100723008A; a rare S100723008B has masked internal ROM.
  • The R25 Turbo ECU uses the same board with different component values and firmware (S100723003).
  • Later units add throttle potentiometers and better algorithms. A rare 1988 to 1992 GTA catalyst ECU (S101100108A) uses an MC68HC11 whose code is read and write protected. Later Safrane and Laguna 3.0 units are reported to be tamper-protected.

Calibrations and table addresses

Known original calibrations, earliest first, are 111B, 111F, 112F, 211D, 311, 501, 601 and 611, identified by a sticker on the PROM. The aftermarket tuner BBR's second fuel map is said to match factory 601B.

AddressContent
002h / 004hVersion number and calibration revision
005hIgnition base map, 9 rows by 13 columns
07AhFuel base map, 9 rows by 13 columns
0EFhCoolant temperature fuelling correction, 9 by 1
125hBattery voltage correction, 9 by 1
14Eh to 151hValues differ between the standard ECU (5C) and R25 Turbo (52)

Speed breakpoints run from 650 to 6,000 rpm and manifold pressure from about -13 to 14 psi. Several addresses (1FFh, 1E0h to 1E1h, 1E6h to 1E7h) are unresolved.

Limits that matter for boost

  • The Renix 1 only sees the throttle as closed, mid or fully open, so it cannot adjust fuelling for airflow changes at a constant manifold pressure. Fuelling can differ with throttle position at the same boost.
  • The standard rev limit is about 6,200 rpm, and the author describes work to raise it to about 6,800 rpm.
  • Defeating the factory boost limit is attributed to a board modification with a 4.7 V zener diode, but the stock board is not modified in the author's unit, so this is reported rather than demonstrated. A wastegate bleed valve is said to be the main change in a typical upgrade.

Not established

The purpose of several addresses, any verified boost-limit modification, and the cars outside the GTA and 25 Turbo that share these calibrations.

Sources