Summary
The 2.0 litre F4R engines on the Sagem S3000 include the naturally aspirated Clio III RS 197 and Megane II 2.0 16v, and the turbocharged F4R-T of the Megane II RS (225 and the 230/R26 variants). Renault’s torque-based control structure means that a remap must raise the torque limit and, on the turbo, the boost target together; raising a power target alone would not be expected to deliver more. Vendors claim gains of roughly 10 to 15 bhp on the naturally aspirated cars and 25 to 35 bhp on the turbo, but none of these are independent results. Controller background is on the S3000 page, and tool support is on Sagem S2000 and S3000 tuning tool support.
What the factory structure implies
Renault’s fault-finding text, summarised on the S3000 page, describes a torque setpoint built from the driver, ESP and automatic gearbox requests, from which throttle position, ignition advance and, on the turbo, the wastegate setpoint are derived. This is an inference from the architecture rather than a statement from a tuner.
- Boost. On the turbo, a normally open solenoid leaves the wastegate fed with boost pressure at rest, so boost stays near the engine minimum of about 1,350 to 1,400 mbar. The same text states a maximum of 275 Nm and 125 kW with boost never above 1,800 mbar, without saying which F4R-T variant that applies to, so it should not be read as the RS output.
- Rev limit. The same documents give hot rev cuts of 6,000 rpm (manual F4R) and 6,300 rpm (automatic F4R). A remap that raises power on an F4R operates inside these limits unless the limiter is also edited.
Vendor gain claims
| Car | Claim | Source type |
|---|---|---|
| Clio III RS 2.0 16v 197 bhp | About +14 to +15 bhp; torque from 215/216 Nm to 230–236 Nm; one vendor quotes +13% torque | Tuner pages and remap statistics |
| Megane II 2.0 16v 136 bhp | About +10 bhp | UK tuner page |
| Megane II RS 2.0T 225 | Roughly 250 to 260 bhp and up to 360 Nm, from quoted stock baselines of 225 to 227 bhp and 300 to 310 Nm | Tuner pages |
These are advertising figures and the stock baselines differ between sellers. One dyno shop states a stage 1 target of about 270 lb ft and 250 to 260 bhp and recommends an induction kit and exhaust. No independent dyno sheets, owner reports on clutch or drivetrain effects, or statement of which torque limiters were changed have been found. For the clutch and supporting-hardware evidence on the 225, see Megane II RS 225 remap limits.
Not established
- Which maps hold the torque limit and boost target on the S3000, and the file layout.
- Whether the 6,000 rpm cut is changed in typical stage 1 files.
- Knock margins on 95 RON fuel and the effect of heat soak on the F4R-T.
Sources
- CSC Motors: Clio RS 2.0i 16v 197hp remap stats, accessed 2026-11-19.
- Celtic Tuning: Clio III RS stage 1, accessed 2026-11-19.
- EFI Tuning: Megane 225/230/R26 dyno re-map, accessed 2026-11-19.
- AltTune: Megane RS (2nd) Sagem S3000, accessed 2026-11-19.
- ND Auto Repairs: Megane 2 2.0i 16v 136hp, accessed 2026-11-19.
- Renault MR-366 and the Megane workshop particulars, as paraphrased on the S3000 page.