Summary
For the turbocharged Megane II RS 225 and R26 (Sagem S3000), the clutch is the component most often named as the first limit on a remap, followed by the stock intercooler and turbo. The evidence is mostly anecdotal and some of it concerns other Megane generations, which is noted where it applies. No logged boost data for a remapped 225 has been found. This page supplements F4R and F4RT Sagem remap expectations.
Clutch
The prevailing view is that the standard clutch loses holding capacity before the software becomes the limit, but experience varies widely.
- One account has a car at about 280 hp on a dyno with the clutch still fine after 40,000 km, and another reports a stock clutch lasting 96,000 miles. Both are old and anecdotal.
- The dual-mass flywheel is not generally regarded as a problem while it remains original; owners who prefer a single-mass flywheel are mostly those who have fitted one.
- K-Tec sells organic and cerametallic kits for the 225, R26 and R26.R, claiming 35% more torque holding for the organic kit. Fitment depends on the flywheel on the car, and 225, R26 and R26.R pressure plates and flywheels are not interchangeable.
- A SEAT Cupra owner reports that some remaps deliver power less aggressively to avoid clutch slip. That is another model and is only an anecdote.
Turbo, intercooler and fuel
- A tuning guide written for the Mk3 RS250 states that the stock turbo is good for about 320 bhp and that the standard intercooler restricts flow as boost rises. Its applicability to the Mk2 is unchecked.
- A generic F4Rt page lists a Mitsubishi twin-scroll turbo for the F4Rt family and cautions that the airflow sensor can restrict torque on larger builds. It gives no boost figure and is not specific to the Sagem car.
Boost data
No logged boost for a remapped 225 has been found. The only measured boost is from a Megane 3 RS265 owner thread: about 1.3 bar in 4th and 5th gear on the RS Monitor and OBD, about 1 bar in normal mode, and a dyno result of 253 hp and 393 Nm at around 30 °C. The owner concluded the car was unmapped. That thread says nothing about the 225 or its ECU. For the Mk2 car the Renault service text summarised on the S3000 page remains the only boost reference: a baseline of about 1,350 to 1,400 mbar and a stated 1,800 mbar ceiling.
Claimed gains
| Claim | Source type | Note |
|---|---|---|
| Stage 1: +30 bhp and +60 Nm (225 to 255 bhp, 300 to 360 Nm) | Tuner pages | Not dyno-verified |
| Stage 2: about +47 hp and +82 Nm | One chiptuning reseller | Compression ratio quoted as 9.0:1 |
| Level 1: 240 to 250 bhp, about 270 lb ft | One UK dyno shop | Depends on modifications |
| R26 build at 273 bhp and 300 lb ft (torque capped) | Single forum build | One car |
Not established
No confirmed turbo failures on remapped 225s have been found, and there is no logged boost for the 225 on a remap.
Sources
- Digital Kaos: Megane 2.0t 225 sagem 3000, search summary only 2026-11-19 (page returned 403).
- RSMegane: Quick question (Megane 3 RS265), accessed 2026-11-19.
- RSMegane: 225 new clutch discussion, search summary only 2026-11-19.
- K-Tec Racing: RTS clutch kits for Megane 2RS 225 / R26, search summary 2026-11-19.
- fastcar.co.uk: Megane RS250 tuning guide, search summary only 2026-11-19.
- TorqueCars: Renault F4Rt tuning, accessed 2026-11-19.
- Chiptuningreseller: Megane 2 RS 2.0T, search summary 2026-11-19.