Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Citroën, Peugeot

On a Peugeot HDi, extra power is limited by the fuel system as much as by the ECU file. The high-pressure pump, rail, injector nozzles and the low-pressure supply all have to deliver the extra fuel at the pressure the file requests. This guide explains how the system works, what a documented injector upgrade involves, and what to check before and after a remap. For which pump and injector is fitted to which engine see Peugeot and Citroën diesel injection pumps and injectors by engine code.

How the common-rail fuel system is arranged

A PSA training document for a Bosch CP1-type HDi system (engine not named in the text) describes this chain:

  • In-tank booster pump (Bosch EKP3 roller pump, 7 bar safety valve) feeds the system. It runs for 2 to 3 seconds at ignition on and while the engine runs.
  • Low-pressure circuit: 5 micron filter with water decanter and an integrated regulator holding about 2.5 bar.
  • High-pressure pump: Bosch CP1 type with three pistons, belt driven at a ratio of 0.5. Rail pressure varies between 200 and 1350 bar, controlled by a regulator on the pump. Pressure reaches 200 bar within 1.5 engine revolutions at start.
  • Third-piston deactivator on the pump reduces absorbed power and fuel heating at low load. If fuel temperature exceeds 106 °C the pump runs on two pistons only.
  • Rail with a pressure sensor and fuel temperature sensor, then solenoid injectors with five-hole nozzles and a return circuit at about 0.7 bar. Spare fuel returns through a cooler under the body.

The same document states that the pump is not a distributing pump and needs no timing setting. That is the key difference from the older XUD and DW8 rotary pumps, covered in the rotary pump guide.

What limits a remap

  • Rail pressure: more fuel at the same nozzle size needs longer injection duration or more pressure. Check requested versus actual rail pressure under full load. A tuner's DCM3.5 repair example reports measured pressure falling below request under load with one injector returning excess fuel; see the PSA HDi guide.
  • Injector nozzle flow: a larger nozzle shortens injection time for the same quantity and helps limit smoke.
  • Low-pressure supply: a weak booster pump, blocked filter or air in the system starves the CP1 pump and gives low rail pressure.
  • Fuel temperature: because the HP pump heats the fuel, high fuel temperature can trigger the two-piston mode and derates.
  • Turbo and airflow: injecting more fuel than the air available gives smoke and high exhaust temperature. A remap must match fuelling and boost.

Documented example: 1.6 HDi 16v injector and turbo upgrade

HDI Tuning's guide covers 16v 1.6 HDi and TDCi engines with Bosch EDC16C3 and EDC16C34, up to 2010. It is one vendor's account, not a factory procedure.

  • The 90 and 110 hp engines are the same apart from the turbo and the injectors. The injector bodies are the same but the 110 injectors have higher-flowing nozzles.
  • The 90 hp car uses a wastegated MHI TD025 turbo; the 110 hp uses a Garrett GT1544V variable-geometry turbo. The author says the GT1544V suits about 145 bhp when remapped, while the TD025 struggles beyond 120 to 125 bhp.
  • Injectors 0445 110 239 must be changed to 0445 110 259 for the 145 bhp remap. Injectors 0445 110 311 need no upgrade for that figure; 0445 110 297 is the optional higher-flow replacement. 0445 110 188 is described as an older part with the same calibration as the 259.
  • Going straight from 239 to 297 cannot be coded because the injector length differs, according to the author; the ECU is said to adapt over time. Do not attempt a code the ECU cannot accept.
  • Coding the injector calibration references through the vehicle's diagnostic software (IDS, Planet or Lexia) only tells the ECU each injector's manufacturing tolerance. It does not tell the ECU the injector flows more. The new injectors must also be reflected in the remapped software, otherwise the engine will inject too much fuel.
  • Reseat the injector seats carefully, record each injector's code and position (cylinder 1 is at the gearbox end), replace the sealing washers and prime the system.
  • The author warns against driving at more than idle until the turbo and injectors are configured in the ECU software, and against cheap reconditioned turbos because the VNT must be calibrated precisely on a flow bench. This turbo has no position sensor, so the ECU cannot know vane position.

The vendor also notes that removing the catalytic converter is illegal for road use. Keep emissions equipment operational on a road vehicle.

Injector rules

  • Bosch and Siemens/Continental or Delphi injectors are not interchangeable, even at the same power rating, according to an injector supplier. Check the stamped code.
  • Always record original injector codes before removal and re-code after replacement.
  • Test or replace injectors as a set where possible, and use the manufacturer's test plan: see the diesel injector catalogue, Bosch part numbers and Siemens and Continental part numbers.

High-pressure pump notes

  • The Bosch CP1 pump on early 2.0 HDi engines (0445010010, RHY/RHZ) and CP1H on the 1.6 (0445010296) are part of a system calibrated with the ECU. There is no published evidence in the sources reviewed that a different pump raises power safely on a standard engine.
  • Pump failure can release metal debris through the whole system; a failed CP1 pump normally means replacing the rail, pipes and injectors or cleaning them thoroughly. Verify this with the manufacturer's guidance for the exact engine.
  • On the 2.0 BlueHDi DW10F, NTN-SNR describes a synchronous single-piston pump reaching up to 2,000 bar, driven by the exhaust camshaft. It is a different design from the three-piston CP1 and parts do not carry across.

Older rotary-pump diesels

XUD and DW8 engines with Bosch VE or Lucas pumps are tuned by adjusting the pump itself (boost-compensator cone, maximum fuel, head size). Owner reports include 9 mm versus 11 mm pump heads and questions over 175 bar injectors; these are anecdotal and cover discontinued pumps. See the rotary pump guide for the sourced discussion and its cautions.

Checks before any HDi tune

  1. Read fault codes and fix rail pressure, boost, MAF and EGR faults first.
  2. Check the low-pressure supply: filter age, booster pump, air in the system.
  3. Log requested and actual rail pressure under load and look for pressure sag.
  4. Check injector return-flow or contribution tests where the tool supports them.
  5. Record the original ECU read, injector codes and software numbers before making changes.

Sources