Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Mazda

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

This 1995 Mazda Miata (NA8) is a turbo build that began with a Fab9 side-mount manifold and, after several years of development, reached an owner-reported 411 wheel horsepower on E85. It runs a built BP engine with a BorgWarner EFR7163 turbo and Haltech Elite 1500 management, tuned on the dyno.Chris, who posts as Downmented, began his turbo project with a 1995 Miata and a Fab9 side-mount manifold. After several years of development, the car reached 411 wheel horsepower on E85. Chris’s build introduction · Owner’s 411 whp summary

Turbo and engine management

The setup uses a BorgWarner EFR7163, 10.5:1 pistons, a non-VVT BP4W head and Haltech Elite 1500 management. The owner reports 25 psi from the ECU during the dyno run; the dyno boost sensor displayed 27 psi, which the owner attributes to incorrect calibration of that sensor.The setup used a BorgWarner EFR7163, 10.5:1 pistons, a non-VVT BP4W head and Haltech Elite 1500 management. Chris reported 25 psi from the ECU during the dyno run. He explained that the dyno boost sensor displayed 27 psi because it was not calibrated correctly. Turbo and engine specification · Dyno-day update and boost-sensor note

After tuning

After the dyno session an oil leak was traced and Falken Azenis RT660 tyres in 245/40 R15 were fitted.Photos and dyno graph from the owner's Miata Turbo Forum thread, reproduced with permission. Car photo · Engine-bay photo · Dyno graphSourcesMiata Turbo build thread: build introductionMiata Turbo: owner's 411 whp summary and turbo and engine specificationMiata Turbo build thread: dyno-day update and boost-sensor noteMiata Turbo build thread: post-dyno maintenance and tyre updateIn a later update Chris documented tracing an oil leak and fitting Falken Azenis RT660 tyres in 245/40 R15. Owner’s post-dyno maintenance and tyre updatePhotos and dyno graph posted by Chris on Miata Turbo Forum, reproduced with permission. Car photo · Engine-bay photo · Dyno graph

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Chris’s 411 whp EFR7163 Mazda Miata

Chris, who posts as Downmented, began his turbo project with a 1995 Miata and a Fab9 side-mount manifold. After several years of development, the car reached 411 wheel horsepower on E85. Chris’s build introduction · Owner’s 411 whp summary

Chris’s dark Mazda Miata outside a workshop

Turbo and engine management

The setup used a BorgWarner EFR7163, 10.5:1 pistons, a non-VVT BP4W head and Haltech Elite 1500 management. Chris reported 25 psi from the ECU during the dyno run. He explained that the dyno boost sensor displayed 27 psi because it was not calibrated correctly. Turbo and engine specification · Dyno-day update and boost-sensor note

Blue cam cover and turbo installation in Chris’s Miata engine bay

Dyno graph from the 1995 Miata’s E85 tuning session

After tuning

In a later update Chris documented tracing an oil leak and fitting Falken Azenis RT660 tyres in 245/40 R15. Owner’s post-dyno maintenance and tyre update

Photos and dyno graph posted by Chris on Miata Turbo Forum, reproduced with permission. Car photo · Engine-bay photo · Dyno graph

Revision 2: Chris’s 411 whp EFR7163 Mazda Miata

This 1995 Mazda Miata (NA8) is a turbo build that began with a Fab9 side-mount manifold and, after several years of development, reached an owner-reported 411 wheel horsepower on E85. It runs a built BP engine with a BorgWarner EFR7163 turbo and Haltech Elite 1500 management, tuned on the dyno.

Chris’s dark Mazda Miata outside a workshop

Turbo and engine management

The setup uses a BorgWarner EFR7163, 10.5:1 pistons, a non-VVT BP4W head and Haltech Elite 1500 management. The owner reports 25 psi from the ECU during the dyno run; the dyno boost sensor displayed 27 psi, which the owner attributes to incorrect calibration of that sensor.

Blue cam cover and turbo installation in Chris’s Miata engine bay

Dyno graph from the 1995 Miata’s E85 tuning session

After tuning

After the dyno session an oil leak was traced and Falken Azenis RT660 tyres in 245/40 R15 were fitted.

Photos and dyno graph from the owner's Miata Turbo Forum thread, reproduced with permission. Car photo · Engine-bay photo · Dyno graph

Sources