Page organisation in this revision
- Page type
- Technical article
- Subject
- Modded Cars
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Maserati
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
Owner’s photo supplied for this article, reproduced with permission.
"Meatball" is a 1985 Maserati Biturbo in which the original V6 has been replaced by a twin-turbo 5.3-litre aluminium LS V8 with a T56 six-speed manual gearbox. The car also has custom front suspension, an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage.Engine and turbo fabrication
The 5.3-litre aluminium LS V8 and twin-turbo system are coupled to the T56 gearbox. In a later revision the 62 mm turbos were mounted to the chassis and exhaust flex sections were added to reduce the load on the pipework. The custom pipework uses numerous pie-cut welded sections.Meatball began as a 1985 Maserati Biturbo. Its builder replaced the original V6 with a 5.3-litre aluminium LS V8 and a twin-turbo system, coupled to a T56 six-speed manual gearbox. In a later revision, the builder mounted the 62 mm turbos to the chassis and added exhaust flex sections to reduce the load on the pipework. The custom pipework uses numerous pie-cut welded sections.Chassis and cooling
The front suspension is custom, based on Nissan 240SX parts, with an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage. The headlamp openings are used as forced-induction air inlets. This is the car’s configuration as listed in the owner’s 2022 update.SourcesReddit r/projectcar: initial 5.3-litre twin-turbo LS swapReddit r/projectcar: intercooler pipework and suspension updateReddit r/projectcar: eight-point roll cage updateReddit r/projectcar: revised twin-turbo mounting and fabricationReddit r/projectcar: 2022 car photo and specificationThe builder described a custom front suspension based on Nissan 240SX parts, an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage. The build also uses headlamp openings for forced-induction air inlets. The 2022 update lists these as the car’s configuration at that time.Owner’s build postsInitial 5.3-litre twin-turbo LS swapIntercooler pipework and suspension updateEight-point roll cage updateRevised twin-turbo mounting and fabricationOwner’s 2022 car photo and specification
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Meatball — twin-turbo LS-swapped Maserati Biturbo

Owner’s photo supplied for this article, reproduced with permission.
Engine and turbo fabrication
Meatball began as a 1985 Maserati Biturbo. Its builder replaced the original V6 with a 5.3-litre aluminium LS V8 and a twin-turbo system, coupled to a T56 six-speed manual gearbox. In a later revision, the builder mounted the 62 mm turbos to the chassis and added exhaust flex sections to reduce the load on the pipework. The custom pipework uses numerous pie-cut welded sections.
Chassis and cooling
The builder described a custom front suspension based on Nissan 240SX parts, an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage. The build also uses headlamp openings for forced-induction air inlets. The 2022 update lists these as the car’s configuration at that time.
Owner’s build posts
Revision 2: Meatball — twin-turbo LS-swapped Maserati Biturbo

Owner’s photo supplied for this article, reproduced with permission.
"Meatball" is a 1985 Maserati Biturbo in which the original V6 has been replaced by a twin-turbo 5.3-litre aluminium LS V8 with a T56 six-speed manual gearbox. The car also has custom front suspension, an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage.
Engine and turbo fabrication
The 5.3-litre aluminium LS V8 and twin-turbo system are coupled to the T56 gearbox. In a later revision the 62 mm turbos were mounted to the chassis and exhaust flex sections were added to reduce the load on the pipework. The custom pipework uses numerous pie-cut welded sections.
Chassis and cooling
The front suspension is custom, based on Nissan 240SX parts, with an independent 8.8-inch rear end, a boot-mounted radiator and an eight-point roll cage. The headlamp openings are used as forced-induction air inlets. This is the car’s configuration as listed in the owner’s 2022 update.
Sources