Page organisation in this revision
- Page type
- Technical article
- Subject
- Modded Cars
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Ford
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
"Blackonblack" is a black 2009 five-door Ford Focus ST225 with the 2.5-litre five-cylinder engine, named after the vinyl graphics the owner, Mike Greenwood, taught himself to produce on a vinyl plotter. The car makes an owner-reported 340 bhp with Revo Stage 2 software.Mike and his wife chose a black five-door ST225 after a test drive sold them on the sound of its 2.5-litre five-cylinder. Mike taught himself to use a vinyl plotter to produce the graphics that gave Blackonblack its name.@focal_alpha, via Stance Auto Magazine. Original photograph, reproduced with permission.
Engine and powerThe owner reports 340 bhp with Revo Stage 2 software supplied by JKM Performance (owner-reported, no dyno sheet given). The specification includes RS injectors, an RS clutch and flywheel, an Airtec plenum and a three-inch KMS Thunderstorm exhaust.Fabrication and detailsAluminium end plates were made for the slam panel after an earlier pair melted. A handle extension for the Mondeo bonnet-latch conversion was 3D-printed. The graphics that give the car its name were produced on a vinyl plotter.SourcesStance Auto Magazine: build story and photo galleryOwner’s Instagram @bonb_stBuild specificationMike reported 340 bhp with Revo Stage 2 software supplied by JKM Performance. His specification includes RS injectors, an RS clutch and flywheel, an Airtec plenum and a three-inch KMS Thunderstorm exhaust. He made aluminium end plates for the slam panel after an earlier pair melted, and 3D-printed a handle extension for the Mondeo bonnet-latch conversion.Build posts and photographsRead the owner’s build story and photo gallery in Stance Auto MagazineOwner’s Instagram @bonb_st
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Mike Greenwood’s 2009 Ford Focus ST225 “Blackonblack”
Mike and his wife chose a black five-door ST225 after a test drive sold them on the sound of its 2.5-litre five-cylinder. Mike taught himself to use a vinyl plotter to produce the graphics that gave Blackonblack its name.

@focal_alpha, via Stance Auto Magazine. Original photograph, reproduced with permission.
Build specification
Mike reported 340 bhp with Revo Stage 2 software supplied by JKM Performance. His specification includes RS injectors, an RS clutch and flywheel, an Airtec plenum and a three-inch KMS Thunderstorm exhaust. He made aluminium end plates for the slam panel after an earlier pair melted, and 3D-printed a handle extension for the Mondeo bonnet-latch conversion.
Build posts and photographs
Revision 2: Mike Greenwood’s 2009 Ford Focus ST225 “Blackonblack”
"Blackonblack" is a black 2009 five-door Ford Focus ST225 with the 2.5-litre five-cylinder engine, named after the vinyl graphics the owner, Mike Greenwood, taught himself to produce on a vinyl plotter. The car makes an owner-reported 340 bhp with Revo Stage 2 software.

@focal_alpha, via Stance Auto Magazine. Original photograph, reproduced with permission.
Engine and power
The owner reports 340 bhp with Revo Stage 2 software supplied by JKM Performance (owner-reported, no dyno sheet given). The specification includes RS injectors, an RS clutch and flywheel, an Airtec plenum and a three-inch KMS Thunderstorm exhaust.
Fabrication and details
Aluminium end plates were made for the slam panel after an earlier pair melted. A handle extension for the Mondeo bonnet-latch conversion was 3D-printed. The graphics that give the car its name were produced on a vinyl plotter.
Sources