Page organisation in this revision
- Page type
- Technical article
- Subject
- Flash chips
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Atmel, Rover
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Rover MEMS 2J remapping references describe replacing the original ECU memory with a rewritable 16-bit device. The following parts are documented aftermarket conversion choices; the sources do not establish them as factory-fitted memory.
DeviceOrganisation and supplyDocumented useAtmel AT49F10251 Mbit, 64K × 16 (128 KiB); 5 V-only flashRover MEMS 2J guide proposes this device for a socketed chip-only conversion, with an appropriate programmer adapter.Atmel AT29C10241 Mbit, 64K × 16 (128 KiB); 5 V-only flashAndrew Revill's MEMS 2J conversion documents this part in a modified ECU with a custom bootloader and board changes.
Device differences
The AT49F1024/1025 datasheet and AT29C1024 datasheet describe different programming schemes. The AT29C1024 uses sector programming in 128-word sectors. Select the exact part and package in the programmer; matching capacity and read interface alone does not establish the write algorithm or board compatibility.
The MEMS 2J references describe different modification approaches. A socketed chip programmed externally does not by itself establish in-ECU or diagnostic-port writing; the cited AT29C1024 installation also changes board wiring and uses a custom bootloader. Confirm the ECU hardware, access time, operating-temperature grade, pinout and programmer support for the actual device before considering a conversion.
See EPROM-pinout flash for related byte-wide devices.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Atmel 16-bit flash for Rover MEMS 2J conversions
Rover MEMS 2J remapping references describe replacing the original ECU memory with a rewritable 16-bit device. The following parts are documented aftermarket conversion choices; the sources do not establish them as factory-fitted memory.
| Device | Organisation and supply | Documented use |
|---|
| Atmel AT49F1025 | 1 Mbit, 64K × 16 (128 KiB); 5 V-only flash | Rover MEMS 2J guide proposes this device for a socketed chip-only conversion, with an appropriate programmer adapter. |
| Atmel AT29C1024 | 1 Mbit, 64K × 16 (128 KiB); 5 V-only flash | Andrew Revill's MEMS 2J conversion documents this part in a modified ECU with a custom bootloader and board changes. |
Device differences
The AT49F1024/1025 datasheet and AT29C1024 datasheet describe different programming schemes. The AT29C1024 uses sector programming in 128-word sectors. Select the exact part and package in the programmer; matching capacity and read interface alone does not establish the write algorithm or board compatibility.
The MEMS 2J references describe different modification approaches. A socketed chip programmed externally does not by itself establish in-ECU or diagnostic-port writing; the cited AT29C1024 installation also changes board wiring and uses a custom bootloader. Confirm the ECU hardware, access time, operating-temperature grade, pinout and programmer support for the actual device before considering a conversion.
See EPROM-pinout flash for related byte-wide devices.
Revision 1: Atmel 16-bit flash for Rover MEMS 2J conversions
Rover MEMS 2J remapping references describe replacing the original ECU memory with a rewritable 16-bit device. The following parts are documented aftermarket conversion choices; the sources do not establish them as factory-fitted memory.
| Device | Organisation and supply | Documented use |
|---|
| Atmel AT49F1025 | 1 Mbit, 64K × 16 (128 KiB); 5 V-only flash | Rover MEMS 2J guide proposes this device for a socketed chip-only conversion, with an appropriate programmer adapter. |
| Atmel AT29C1024 | 1 Mbit, 64K × 16 (128 KiB); 5 V-only flash | Andrew Revill's MEMS 2J conversion documents this part in a modified ECU with a custom bootloader and board changes. |
Device differences
The AT49F1024/1025 datasheet and AT29C1024 datasheet describe different programming schemes. The AT29C1024 uses sector programming in 128-word sectors. Select the exact part and package in the programmer; matching capacity and read interface alone does not establish the write algorithm or board compatibility.
The MEMS 2J references describe different modification approaches. A socketed chip programmed externally does not by itself establish in-ECU or diagnostic-port writing; the cited AT29C1024 installation also changes board wiring and uses a custom bootloader. Confirm the ECU hardware, access time, operating-temperature grade, pinout and programmer support for the actual device before considering a conversion.
See EPROM-pinout flash for related byte-wide devices.