The ZF 4HP20 is a transverse four-speed automatic for the larger Citroën engines, including the C5 with the ES9 V6. An auto-adaptive ECU controls the lock-up converter, the shifts and the driver programs. The stated torque capacity is 330 N·m, given for the C5 ES9 at 3,500 rpm. The unit weighs 90 kg with oil and the ECU. There are no band brakes: the friction elements are multiplate clutches. A step-down gear sits in the centre, and the differential has sealed outputs. Gearbox oil is pressurised. The final drive is splash-lubricated.
A riveted plate carries the serial number, the parts-list number (the last three figures are the ones used in identification) and the component reference. The ECU label carries the ZF parts-list number, which identifies the software, the hardware version, the program-data version, the manufacturing date and the serial number. The same identity is in the diagnostic identification menu. The ECU is an 88-terminal Flash unit.
Gear train
Two Simpson trains are joined so that annulus C1 is connected to planet carrier PS2, and annulus C2 is connected to planet carrier PS1. Output is through gear PS0. Tooth counts are sun P1 39, sun P2 37, planet S1 21, planet S2 29, annulus C1 81 and annulus C2 95.
| Gear | Driving | Reacting | Ratio |
|---|---|---|---|
| 1 | P2 | P1 | 2.718 |
| 2 | C1–PS2 | P1 | 1.481 |
| 3 | P2 and C1–PS2 | none | 1 |
| 4 | C1–PS2 | P2 | 0.720 |
| Reverse | P2 | C1–PS2 | 2.568 |
The element captions name a lined-disc clutch B and brakes C and D, plus further elements E and F on the operating diagrams. Which element is applied in each gear follows the unit diagram.
Converter
The pump is coupled to the engine, the turbine to the gearbox, and the reactor sits on a freewheel between them. Torque is multiplied by up to 2.5 in the converter phase. Coupling efficiency is 0.98, and 1 when locked. The ECU has three converter states. Open is a normal converter. Closed joins pump and turbine, so engine braking is available and fuel use falls. Controlled holds about 50 rpm of slip between pump and turbine, which filters the engine’s torsional vibration and hesitation. Lock-up is available in 2nd, 3rd and 4th, and it is made by reversing the direction of oil flow. The clutch sits between the engine drive plate and the turbine.
Pressure and the shift
Line pressure, which is the pressure on the clutches and brakes, is adapted from engine torque, the time the shift actually takes, play and internal wear. The ECU compares the shift it measured with the theoretical shift time, and it compares engine speed with turbine speed to judge the converter. The AL4 uses a line-pressure sensor for the same job. This gearbox adapts pressure from torque, shift time and wear.
The hydraulic-unit connector carries four proportional valves, EDS3, EDS4, EDS5 and EDS6, switched on the earth side, an on/off valve MV1, and a fixed valve MV2. The proportional valves have their own 12 V feed. MV1 and MV2 have a separate 12 V feed. No per-gear assignment of these valves is given with the connector.
Downshifts belong entirely to the ECU, from load, road speed and the driving conditions. A double downshift, 4th to 2nd or 3rd to 1st, is authorised, and a single downshift can be forced for engine braking on the brakes or downhill. A sudden lift is kept from causing an upshift, so engine braking remains. Kick-down is load above 95 percent and still depends on road speed. A floor mat that shortens pedal travel will stop that threshold being reached. Torque reduction during a shift is a brief cut of ignition advance from a programmed table. Idle is compensated so the car creeps less with a gear engaged.
The lever has seven positions, P, R, N, D, 3, 2 and 1, on an offset grid. Shift-lock holds P until the brake is pressed. A key-lock, which would trap the key unless the lever is in P, was not used on these Citroëns. A lights-on style buzzer can stand in for it. Both outputs exist as version-dependent pins. The gearbox refuses these lever movements at the speeds given:
| Movement | Prohibited from |
|---|---|
| D to R | 10 km/h |
| D to 3 | 165 km/h |
| 3 to 2 | 110 km/h |
| 2 to 1 | 60 km/h |
Programs
Normal is the base program and is also called DSP, the dynamic shift program. The ECU learns the driver and moves the shifts to suit. It adapts, over the life of the car, to driving style, to the vehicle being unladen, laden or towing, to uphill, downhill, low adhesion and town driving, to shift behaviour, oil condition and wear, and to engine torque, speed and temperature. Sport keeps the shifts automatic and spends more fuel. Snow removes 1st except when 1st hold is selected, and it downshifts less often. In the hold positions the gearbox uses the gear the lever is showing: 3rd in 3, 2nd in 2, 1st in 1. An upshift at no load is refused. The sport or snow indicator flashes to warn of a gearbox problem.
Connector
Only the pins that are assigned are listed. Several selector-position pins repeat the same description, and both speed sensors appear on two pins each: one pair is the signed sensor wires and the screen, and the second pair repeats the sensor name.
| Pin | Function |
|---|---|
| 1 | EDS4, earth-side |
| 3 | +12 V for the proportional valves |
| 4 | EDS6, earth-side |
| 5 | EDS3, earth-side |
| 6 | Power earth |
| 8, 9, 36, 37 | Selector position, multifunction switch |
| 10 | Brake switch |
| 12 | Snow program |
| 14 | Output-speed sensor, minus |
| 15 | Output-speed sensor screen |
| 16 | Turbine speed, plus |
| 20 | Fan-operation request |
| 21 | Oil-temperature sensor earth |
| 22 | Gearbox oil temperature |
| 23 | Turbine-speed sensor screen |
| 25 | Display output, depending on the vehicle |
| 28 | Electrovalve earth |
| 29 | EDS5, earth-side |
| 30 | MV1, earth-side |
| 31 | +12 V after ignition |
| 32 | Shift-lock relay, earth-side |
| 33 | MV2, earth-side |
| 34 | Power earth |
| 38 | Throttle angle from the engine ECU |
| 39 | Engine torque from the engine ECU |
| 40 | Rev-counter information |
| 42 | Gearbox output speed |
| 44 | Turbine speed |
| 45 | Sport program |
| 47 | L-line, unused on this listing |
| 49 | Key-lock, depending on country |
| 50 | K diagnostic line |
| 51 | Gearbox position and torque-reduction request, to the engine ECU |
| 52 | +12 V for MV1 and MV2 |
| 54 | +12 V after ignition |
| 55 | Permanent battery positive, keeps the diagnostic memory |
Oil
The C5 ES9 specification is Esso LT 71141. Capacity is 7.7 to 8.3 litres. A drain removes 2.7 to 3 litres. The oil is filled for life. The level is checked every 60,000 km.
The check is made with the engine hot and the gearbox at about 80 °C. With the foot on the brake, every gear is selected, the car is level, the lever is in P or N, and the engine idles. The dipstick must lie between the minimum and maximum marks, and the span between those marks is 0.5 litre. The level is never taken above the maximum. A high level heats the oil and causes leaks. A low level damages the gearbox. Dirt collects around the dipstick, so the area is cleaned before the stick is removed. A leak at the stick is cured by replacing its two O-seals. There is no old-oil counter. Oil ageing is one of the quantities the adaptive strategy takes into account, and there is no counter to reset.
Initialisation
A download updates the ECU software. Initialisation clears every adaptive value the ECU has stored. It is done after an ECU replacement, a gearbox replacement, or a download, with the ignition on, the car stationary and the lever in P or N. It is a deliberate erasure of the learnt shifts. The road test that follows uses frequent changes through all the gears so the ECU can store a new difference between reference and actual. The diagnostic tool can also program the accelerator pedal and configure the ECU. The pedal-programming conditions for this gearbox are separate from the AL4 routine.
Fault modes
A stored fault keeps the code, the nature of the failure, whether it is permanent or temporary, the conditions when it appeared, and an age counter that runs up to 50. The driver is told by the sport or snow indicator flashing. Emergency behaviour is hydraulic 3rd, or 4th if the fault appears while the car is already in 4th, because a shift into 3rd at that road speed can overspeed the engine. The held gear lasts until the ignition is switched off, and the next start is in hydraulic 3rd. Missing data can also be replaced by a calculated value, so electronic control continues on a fixed characteristic. A shift from P to R or from N to R can hesitate hard in that state.
| Fault | Mode |
|---|---|
| Engine speed, turbine speed, output speed, gear-change check | S1 |
| Throttle position | S6 and S12 |
| Multifunction switch, electrovalves, regulators, battery voltage, the ECU itself, gear-engaged coherence, overspeed protection | S0 |
| Program selector | S10 |
| Stop switch | S8 |
| Engine-torque signal | S9 |
| Torque reduction | S7 |
| Engine temperature | S4 |
| Oil thermistor | S13 |
| Mode | What the car does |
|---|---|
| S0 | Hydraulic 3rd. In 4th, 4th is kept until the ignition is switched off. |
| S1 | The engaged gear is kept, then S0 once the lever returns to P or N. |
| S3 | Oil temperature is replaced. The mode is defined and is not attached to a fault in the list above. |
| S4 | Engine temperature is replaced. |
| S6 | Load is fixed at 50 percent. |
| S7 | Kick-down is removed from downshifts. |
| S8 | Stop-switch information is replaced, depending on the function. |
| S9 | Load and engine speed are recalculated. |
| S10 | The normal program is held. |
| S12 | A fixed DSP law is used. |
| S13 | The value is recalculated from the starting temperature and the time since then. |
Fan control, shift-lock and key-lock have no emergency mode attached.
Faults seen on the C5
A judder on the 2nd-to-1st downshift as the car stops, on the XFX V6, is the downshift landing at the same moment the injection restores fuel. The driver feels both. A gearbox calibration with different shift timing is the correction, obtained as a software update.
A cabin resonance in 2nd and 4th on XFX and 4HX is a calibration complaint. If the engine is cold, one acceleration past 50 percent load cancels the catalyst-heating law, and the noise may leave with it. If the resonance remains after that, it is still a calibration issue rather than a mechanical strip.
On a restyled C5 that will not crank, with a message on the multifunction screen, the gearbox software is 98 592 059 80. If it already is, the displayed lever position is compared with the lever. At the PSF1 28-way grey connector, pin 15 is continuous to earth in P and in N. In P, pin 37 of the 88-way black ECU connector has 12 V. The selector cable is adjusted if those checks fail.