Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

This reference examines selected torque-demand and protection descriptions in the publicly indexed SCQ110_C_OEM.a2l. The definition describes itself as an enriched Audi/VW Simos 19.3 LK3evo project with reference list SCQ110 and EPK VWSCQ110. Its origin, rights, completeness and match to a specific ECU or binary are unverified. Labels and axis references are leads for inspecting a matched file, not verified calibration values, evidence that a map is active or proof of the calculation at runtime.

Different torque quantities and axes

The A2L describes DATA_DrvDemA.DrvDemA_tqCluDemAceped00_M_VW as accelerator-pedal demand expressed as clutch torque. Its axis inputs are named Pt_nClu_VW and AccP_r_VW. A separate DATA_DrvDemA.DrvDemA_tqCluDemAcepedFast00_M_VW has the same named inputs and is described as the corresponding clutch-torque demand for fast velocities. The entries' names do not identify the actual changeover speed or establish that either is selected in a particular run.

DATA_DrvDemA.DrvDemA_tqWhlDemAceped00_M_VW is instead described as pedal demand expressed as wheel torque, with inputs named DrvDemA_vVehAbs_VW and AccP_r_VW. Clutch-torque demand and wheel-torque demand are distinct labelled quantities: do not assume identical units, axes, selection logic or numerical values merely because both mention the pedal. The suffix 00 does not by itself identify a drive mode or gear. The other indexed entries, conversion methods and exact input definitions need to be checked in the matched software.

Examples of differently scoped limits

ip_tqi_pow_max_bas is described as maximum allowed indicated torque at full load for torque limitation, with axis inputs named n and gear. This label does not establish a wheel-torque limit or an active limit in a particular log. ip_fac_pow_max_toil is described as a factor for torque-limit correction based on oil temperature and references toil and n; it is a correction factor, not itself a torque request or measured oil temperature.

Separately, the file describes ip_tqi_lim_heat_gdi as a torque limitation that reduces combustion heat for direct-injector protection, with input n. The definition alone does not establish activation criteria, actual values, a safe threshold or the resulting output torque. Do not disable or copy a protection to conceal a fault or to force a higher request.

Using a matching log

COBB's Mk8 / 8Y tuning guide describes a simplified pedal-to-torque, air-setpoint and boost-target path with limits at several stages. Its editor descriptions are a separate product example; they do not establish that its table definitions correspond to the SCQ110 entries above.

Record actual ECU hardware and software, gearbox, gear, fuel, hardware, faults and operating conditions. Where supported, compare pedal position, engine and vehicle speed, driver demand, relevant torque limitations, estimated torque, air target and pressure target versus actual, with oil and coolant temperatures. Check each channel's definition, units, update timing and whether it is requested, estimated or measured. An ECU torque estimate is not an independent wheel-torque measurement, and one low value cannot by itself identify the limiter or its cause. See EA888 Evo4 torque demand and air model for a separate tool-specific guide.

Source and verification scope

Public SCQ110_C_OEM.a2l, characteristic labels and axis-input references, accessed 17 November 2026. The inspected text was 60,057,673 bytes; SHA-256 6473bf25107af882ebb3eea6cb0d57c223b2d005451df031ab546bfd1487f45e. The hash identifies the examined file; it does not authenticate the text, rights, fitment or ECU behaviour. COBB Mk8 / 8Y tuning guide, tool-specific torque and airflow overview; accessed 17 November 2026.