Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

This guide concerns the 1.2 TSI/TFSI CBZA and CBZB examples with Simos 10 described in Audi Self-Study Programme 485. Their charge-air cooler is liquid-cooled and integrated into the intake manifold. An excessive intake-temperature signal can affect the permitted charge pressure, so a loss of repeatability after heat soak deserves investigation before changing boost or protection maps. The component names and behaviour below are specific to the documented installation; verify the fitted engine and current service information.

Two connected cooling systems

Audi describes a charge-air cooling system and a separate engine cooling system, connected through non-return valves and a flow restrictor. The charge-air circuit includes coolant circulation pump V50, the charge-air cooler, an auxiliary cooler and the turbocharger. The engine system has a mechanically driven coolant pump and separate flow paths for the cylinder head and block. V50 and the mechanical pump do different jobs; an ordinary engine-coolant reading does not establish the flow or performance of the charge-air circuit.

SSP 485 identifies additional coolant pump relay J496 and V50 in its Simos 10 system overview. Use the current wiring diagram and guided tests for the exact vehicle to establish pump supply, control and operation. The training document does not provide a universal V50 activation schedule or diagnostic temperature threshold. Do not assume that a stationary or silent pump at one moment proves a fault.

Read both air-temperature channels in context

Audi places charge-pressure sender G31 with intake-air-temperature sender G299 in the charge-pressure pipe, and manifold-pressure sender G71 with intake-air-temperature sender G42 in the intake-manifold path after the cooler. The ECU uses G71 and G42 to calculate manifold air mass. Audi states that the G299 temperature signal can reduce boost to protect components when temperature is too high; G42 is also used as a correction for charge pressure. The publication does not give a universal intervention temperature or tune value.

Temperature readings are influenced by their physical positions, throttle state, heat soak, sensor response and flow. A difference between G299 and G42 is useful context, but is not on its own a direct measure of coolant flow or intercooler efficiency. Confirm the logger's channel descriptions and units, and compare temperatures under similar load, speed, ambient conditions and time since the previous run.

Logging and workshop checks

  1. Record engine and ECU identification, calibration, hardware, coolant-service history and fault codes. Note ambient temperature, coolant temperature, the duration of heat soak and any recent coolant loss or work.
  2. Where supported, log G299 and G42, engine speed, load, throttle, charge-pressure request and actual pressure, coolant temperature, ignition corrections, lambda and relevant intervention status. Include time after a stop or repeated load so that readings can be compared at equivalent operating points. Check whether pressures are absolute or gauge and whether each displayed value is measured or calculated.
  3. If the downstream temperature or pressure response changes between comparable tests, investigate the cooling circuit, coolant level and leaks, auxiliary cooler obstruction, pump power and operation, and temperature-sensor plausibility using the vehicle-specific procedure. Heat soak, a sensor issue and inadequate coolant circulation can produce similar log patterns; the log alone does not identify which one is present.
  4. After cooling-system work, use the current vehicle-specific filling and bleeding procedure. Audi SSP 485 explains that the check valves and restrictor require the complete system to be vented and describes VAS 6096 or a diagnostic-tester test program for its example. A correctly filled expansion tank alone does not establish that all circuit air has been removed.
  5. Repeat the same test after repair, including the cooling system's guided checks where applicable. Compare the pressure request as well as actual pressure: a lower request and a target that is not met suggest different diagnostic paths. Preserve temperature-related protection while correcting the underlying fault.

Engine warm-up is a separate function

In the SSP 485 example, the engine's mechanical pump is continuously driven but can temporarily restrict flow using a vacuum-operated plate controlled through solenoid N492 during warm-up. Audi describes a de-energised valve with the plate returned to the flow position; a fault leaving flow restricted can cause overheating. This warm-up mechanism is separate from the electric V50 charge-air circuit and should be diagnosed under the applicable service procedure. A warm-up strategy is not evidence of a charge-cooler pump fault.

For pressure sensors, wastegate feedback and replacement-turbo checks, see Simos 10 1.2 TSI charge pressure and wastegate diagnosis.

Sources

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.