Where MS42.0 is fitted
Siemens MS42.0 is the engine control system on the E46 with the M52 TU. The M52 TU B28 runs from June 1998 to June 2000, and the M52 TU B25 from June 1998 to September 2000. It was built for low-emission compliance and for on-board diagnosis. The air-mass meter is a Siemens hot-film unit. Functionally it is the same meter as on the previous system. The designation 2 Type B means the housing is smaller. Flash layout, definitions and the shared fuel and camshaft maps are on the MS42 hub.
Oxygen sensors
The system uses Bosch LSH 25 sensors, the same narrowband behaviour as the earlier Bosch installations, with a voltage from 0 to 800 mV. The pre-catalyst sensors sit on top of the exhaust manifolds, and the catalysts are part of the manifolds. Injector opening time follows the amplitude of the sensor signal and the time the signal takes to switch.
Crankshaft and camshafts
The crankshaft sensor is a dynamic Hall sensor mounted through the block. The pulse wheel is on the crankshaft, and the signal starts as soon as the crank begins to turn. Each camshaft has a static Hall sensor, so the positions are known as soon as the ignition is on, before the engine is cranked. The intake sensor provides cylinder-bank detection for the preliminary injection, synchronisation, a substitute engine-speed signal if the crankshaft sensor fails, and the position feedback for intake VANOS. The exhaust sensor is the position feedback for exhaust VANOS. There is no substitute value if a camshaft sensor fails. The engine runs in the fail-safe with no VANOS movement, and the loss of torque is obvious. The impulse wheels bend easily during repairs.
Misfire
Misfire is read from the crankshaft. Each firing segment is 120° of crank angle and starts 78° before top dead centre. The control unit times every segment. Equal combustion gives equal times. A misfire lengthens that cylinder’s segment by a fraction of a millisecond. The times are corrected for sensor adaptation and compared with limits that depend on engine speed, load and temperature. A segment that runs long stores a misfire fault for that cylinder. Over an interval of 1000 crankshaft revolutions the misfire counts of all cylinders are added, and a sum above the threshold is a fault. Depending on the rate, the warning lamp comes on, fuel to that cylinder may be cut, and lambda control may drop to open loop. Faults are weighted so the control unit can tell an emissions misfire from one that will damage the catalyst.
Air mass and fuel
Rail pressure is held at a constant 3.5 bar. The regulator is no longer moved by manifold vacuum. The vacuum line goes to the crankcase cyclone separator, so a split diaphragm cannot pull fuel into the manifold. The control unit itself adds or removes fuel for manifold-vacuum changes, from throttle position, the air-mass meter and load. The Siemens injectors spray at an angle through a directional plate with two outlets, a dual-cone pattern, and the lower body is jacketed in metal. Injector control is unchanged from MS41.1. Engine-speed limiting and the vehicle-speed limit, about 128 mph, are done by dropping injection on individual cylinders so the cut is progressive rather than a single chop.
Ignition
MS42.0 fires more than one spark. Multiple spark is there for a clean burn during start and idle, which keeps the long-life plugs cleaner, and it is active up to about 1350 rpm, the limit moving with engine temperature, and up to 20° after top dead centre. It depends on battery voltage. A low battery means less primary current and a longer time to build the coil, so fewer extra sparks. A high battery means more of them. A 240 Ω shunt is still in the secondary so the control unit can see secondary ignition faults.
Double VANOS
Both camshafts move. The low and mid range, about 1500 to 2000 rpm, gains torque without giving up the top end. Idle overlap is reduced, so combustion at idle is more complete. Part-load overlap is the internal exhaust-gas recirculation, which cuts NOx and lets residual gas finish burning. After a cold start the catalyst warms faster and the raw emissions are lower, and consumption falls.
Each camshaft has a helical gear insert, a sprocket with an adjustable gear, its own actuator, a three-way solenoid, an impulse wheel and a Hall sensor. Base timing is the gear position and the chain tensioner. Oil pushes a helical cup, and the angled teeth turn that push into rotation added to the camshaft, advancing or retarding it. The rate depends on oil temperature, oil pressure and engine speed. Extremely hot oil deactivates VANOS, and the engine loses power. Oil of the wrong viscosity, thick enough that the actuators cannot move, can store a fault.
Intake, idle and the throttle
The intake is split into two groups of three runners, which is the low-speed torque path. Separate turbulence bores, 5.5 mm where they meet the head, take air from the idle actuator to one intake valve of each cylinder. Feeding one valve, through a small section, spins the charge and steadies the combustion. Below about 3750 rpm the resonance path uses the wave between the banks: as one cylinder’s intake closes, the next cylinder on the other bank is opening and takes that pulse. Above about 3750 rpm the open intake is fed from both resonance tubes.
Idle air is a dual-winding rotary actuator, ZWD 5. It sets the initial air quantity, and below 0 °C the motor-driven throttle opens with it. Idle speed is a preset that moves with load. The control unit watches rpm against each preset, meters the low-rpm air even while the car is moving, limits vacuum, and smooths the step from acceleration into deceleration. Idle rises during warm-up, with the air conditioning, in gear, with the heater, and at each electric-fan speed. A service routine can also raise the nominal idle. If the actuator fails, the throttle takes over idle and the EML lamp comes on. If the failure is an actuator stuck open, so the air is too high, VANOS and knock control are switched off and the power loss is obvious.
The motor-driven throttle, MDK, is inside this control unit: precise air control, traction control, engine-drag control, cruise control, and a start position when the coolant is below 0 °C. The pedal potentiometer is in the throttle housing. A cable still works the throttle potentiometers and, if the motor control has failed, opens the plate as a mechanical backup.
Emergency operation 1 is a fault that spoils the throttle without making the car unsafe. The warning lamp comes on, the motor is switched off, and the springs and the cable set the plate. The idle actuator closes and the ignition is retarded to take the power back, and injectors are cut as a further limit. If a potentiometer has failed, the engine can still be worked slowly up to maximum speed, with the power held down. Emergency operation 2 is a further fault, or a plausibility failure such as the pulley position disagreeing with the throttle position and the airflow. It is also entered by pressing the accelerator and the brake together, or by a fault in the brake-light switch check. Engine speed is then held a little above idle, on top of the emergency 1 limits.
Cruise, torque and the brake vacuum
Cruise control lives in the control unit because the throttle is already a motor. The steering-wheel switches are encoded in the multifunction switch and arrive on a serial wire. The clutch switch drops cruise so a gear change cannot over-rev the engine. The brake-light switch and the brake-light test switch drop cruise and also supervise the throttle. Road speed for ordinary running is the right-rear wheel from the ABS module. Road speed for cruise is the average of the two front wheels, on CAN.
When ASC, DSC, MSR or the gearbox asks for a torque change, also on CAN, less torque is ignition retard first, then the idle actuator and the throttle close. More torque, for MSR, is the idle actuator and the throttle opening.
A jet pump keeps brake-booster vacuum when the idle actuator is being moved for the air conditioning, for a gear engaged, or during warm-up below 70 °C. If the gearbox is in fail-safe the jet pump runs all the time. The control solenoid is sprung open, and that open state is when the extra vacuum is applied. Powering the solenoid closed limits the extra vacuum to the booster.
Cooling fan
The fan is controlled by a power stage on the fan housing, fed by a 50 A fuse in the glovebox above the fuse bracket. The control unit sends a pulse-width signal. The calculation uses coolant outlet temperature, a calculated catalyst temperature, vehicle speed, battery voltage, and air-conditioning pressure, which the climate control computes and sends on the K-bus. At the first start the fan runs briefly at 20 % and then stops. That is a test: as the fan slows it generates, and the voltage has to match the speed the power stage expects. If it does not, the signal wire is pulled to ground and a fault is stored. A stored fan fault is a reason to check that the fan actually turns. After the test, 10 % command is one-third speed and 90 to 95 % is full speed. Below 10 % and above 95 % the fan is stopped. Hysteresis stops the speed hunting. Switching the air conditioning on does not start the fan at that instant. After the engine is switched off the fan can run for up to 10 minutes, at a speed set by the calculated catalyst temperature, to clear a heat soak.
Evaporative system and secondary air
The purge valve is driven at 10 Hz and is sprung closed. The valve body differs from the MS41.1 part. The control does not. The leak-diagnosis pump and the charcoal canister sit together under the right rear trunk floor. The pump is a separate, sealed unit: a vacuum chamber, a pneumatic pump chamber, a solenoid the control unit switches, and a reed switch that sends a voltage back. It is replaced as that unit, not with the canister. It can find a leak down to 0.5 mm. On every cold start the solenoid is energised, manifold vacuum lifts the diaphragm, and the air drawn into the lower chamber on the upstroke is pushed into the evaporative system. The control unit times how long the reed switch takes to open against the pressure under the diaphragm. Turning the ignition on also runs a static check of the pump circuit.
Secondary air is the MS41.1 function with a different inlet valve. The valve bolts to the cylinder head and blows through a passage machined in the head, so there are no external distribution pipes. Immediately after a cold start, between −10 and 40 °C, fresh air is blown into the exhaust manifold to light the catalyst sooner and to oxidise hydrocarbons. Below −10 °C the pump runs only to blow out water that could freeze in the pipes. The pump runs in open loop, with the oxygen-sensor heaters on, coolant and engine speed inside their windows, and no secondary-air fault already present. How long it runs depends on the engine and the conditions. The pre-catalyst oxygen sensors are what the control unit uses to see that the air actually arrived.
From June 2000 on the E46, and from September 2000 on the E39, E52 and E53, the 20-pin diagnostic socket is deleted. Model year 2001 cars in that run no longer have it.