RM-Primis VAG 1.8T ME7.1 ME7.5 plug-in ECU is an application-specific RM Racing Electronics kit combining its RM-Primis standalone ECU with an adapter to selected original vehicle engine harnesses. Manufacturer product information.

Applications and compatibility
The manufacturer lists ME7.1 or ME7.5 1.8T applications. The manufacturer lists AJQ, APP, ARZ, ARX, ARY, AUM, AUQ, APU, AVJ, AWT, BEX, BFB, BBU, AWC, AVC, APH, BAM and AQX engine codes.
The vendor describes a separate ME7.1/ME7.5 harness adapter, ECU adapter cable and optional LSU 4.9 sensor. Electronic-throttle control depends on the selected ECU set; do not apply the M3.8 adapter schedule or assume every vehicle module is retained. Confirm the original ECU code, throttle, loom, immobiliser and CAN dependencies before ordering or wiring.
Control and wiring
RM-Tuner handles tuning and logging. The manufacturer lists 400 kPa MAP, CAN, six ignition and six injection channels, boost and variable-cam control, with electronic throttle and Bosch LSU wideband equipment dependent on selected options. The supplied kit includes the RM-Primis ECU and a VAG-specific adaptor; it is not simply a reflashed stock ECU.
A complete cavity-by-cavity ECU, adapter and original-vehicle pin schedule is not verified on the sales page. Obtain the exact kit documentation and use the RM-Primis documentation for the delivered hardware.
Reference
Manufacturer application and kit listing; RM-Primis platform.
Adapter auxiliary connectors — Audi/VW ME7.5 and 7.x adapter
RM Racing’s RM-Primis booklet, PDF page 14, documents the following six-way accessory connector assignments for the adapter named above. These are the adapter’s auxiliary and LSU connectors, not the factory vehicle connector and not the 32-way board-to-ECU headers shown in the drawing. The booklet gives a generic 32-way header schedule separately on PDF page 12; see the board-header tables below. Match the actual adapter board and revision before using this schedule. The booklet says the marked high-side channels are converted on the adapter board to ground-switching outputs; select the corresponding high-side channel in RM-Tuner. It also states that injector outputs are low-side outputs and can be used as general-purpose outputs, subject to the actual configuration.
LSU 4.9 wideband adapter connector
| Adapter pin | Signal | Sensor wire colour | LSU 4.9 sensor pin |
|---|---|---|---|
| 1 | H− | White | 3 |
| 2 | VS | Black | 6 |
| 3 | Rcal | Green | 5 |
| 4 | H+ | Grey | 4 |
| 5 | VS/IP | Yellow | 2 |
| 6 | IP | Red | 1 |
Auxiliary connector 1
| Pin | Manufacturer function |
|---|---|
| 1 | CAN low |
| 2 | CAN high |
| 3 | Spare voltage input 3 |
| 4 | MAF / analogue voltage input |
| 5 | Low-side general-purpose output 5 |
| 6 | Spare voltage input 2 |
Auxiliary connector 2
| Pin | Manufacturer function |
|---|---|
| 1 | High-side output 2 (converted on board to low-side output) |
| 2 | High-side output 3 (converted on board to low-side output) |
| 3 | High-side output 4 (converted on board to low-side output) |
| 4 | Injector output 6 (low-side; may be used as GP output) |
| 5 | Injector output 5 (low-side; may be used as GP output) |
| 6 | Spare temperature input 1 |
RM-Primis plug-in adapter board headers
The RM Racing booklet, PDF page 12, labels the RM-Primis plug-in adapter’s left and right 32-position board headers looking straight at the board. The model-specific diagrams in the booklet show the same header layout; use these tables only after matching the actual board and revision. These are board-side connector positions, not the original vehicle’s loom or ECU connector cavity numbers. Vehicle-specific adapters can route or condition signals differently; consult the model-specific auxiliary notes above and confirm the wiring before connecting devices.
Header 1 — left side of board
| Board-header position | Manufacturer function |
|---|---|
| 1 | Injector output 1 |
| 2 | Injector output 2 |
| 3 | Injector output 3 |
| 4 | Injector output 4 |
| 5 | Injector output 5 |
| 6 | Injector output 6 |
| 7 | Ignition output 1 |
| 8 | Ignition output 2 |
| 9 | Ignition output 3 |
| 10 | Ignition output 4 |
| 11 | Ignition output 5 |
| 12 | Ignition output 6 |
| 13 | Fuel pump output |
| 14 | Low-side GP 1 |
| 15 | Low-side GP 2 |
| 16 | Low-side GP 3 |
| 17 | Ground |
| 18 | Ignition-switch input +12 V |
| 19 | Permanent battery +12 V |
| 20 | LSU IP |
| 21 | LSU RCAL |
| 22 | LSU VS/IP |
| 23 | LSU VS |
| 24 | LSU H+ |
| 25 | LSU H− |
| 26 | Tachometer output |
| 27 | High-side GP 4 |
| 28 | High-side GP 3 |
| 29 | High-side GP 2 push-pull |
| 30 | High-side GP 1 push-pull |
| 31 | Low-side GP 5 |
| 32 | Low-side GP 4 |
Header 2 — right side of board
| Board-header position | Manufacturer function |
|---|---|
| 1 | Throttle position sensor input |
| 2 | Coolant temperature sensor input |
| 3 | Intake air temperature sensor input |
| 4 | Digital / trigger input 1 (pull-up selectable) |
| 5 | Digital / trigger input 2 (pull-up selectable) |
| 6 | Digital / trigger Hall input (no pull-up) |
| 7 | MAF / analogue voltage input |
| 8 | Spare voltage input 1 |
| 9 | Spare voltage input 2 |
| 10 | Spare voltage input 3 |
| 11 | Spare voltage input 4 |
| 12 | Spare voltage input 5 (pedal 2 when DBW) |
| 13 | Spare temperature input 1 |
| 14 | Spare temperature input 2 (pedal 1 when DBW) |
| 15 | DBW TPS input 2 |
| 16 | 5 V output for sensors |
| 17 | DBW motor + |
| 18 | DBW motor − |
| 19 | Ground |
| 20 | Ground |
| 21 | Ground |
| 22 | 5 V output for sensors |
| 23 | CAN low |
| 24 | CAN high |
| 25 | Knock sensor 2 − |
| 26 | Knock sensor 2 + signal |
| 27 | Knock sensor 1 − |
| 28 | Knock sensor 1 + signal |
| 29 | Variable-reluctance sensor 2 − |
| 30 | Variable-reluctance sensor 2 + |
| 31 | Variable-reluctance sensor 1 − (adjustable threshold) |
| 32 | Variable-reluctance sensor 1 + (adjustable threshold) |