RM-Primis BMW M50 and M50TU plug-in ECU is a vehicle-specific package based on the RM Racing Electronics RM-Primis standalone ECU. The manufacturer describes an application-specific adapter between the standalone controller and the original vehicle loom; the ECU and adapter are distinct components. Source: manufacturer product documentation.

Application and installation
The manufacturer lists M50 and M50TU single-VANOS or non-VANOS engines, including E36 320i/325i and E34 520i/525i. Check the actual engine, original ECU part number, connector, donor loom, immobiliser and transmission with the supplier; trim or model-year labels alone do not establish compatibility.
The kit is described as the RM-Primis ECU with a BMW 88-pin harness adapter, ECU adapter cable and model-specific jumpers. The listing also names E39 and several Z3 variants; verify the actual M50 engine and original ECU rather than inferring compatibility from chassis alone.
Control and tuning
RM-Tuner provides calibration and data logging. The manufacturer describes a built-in 400 kPa MAP sensor, wideband compatibility with LSU 4.9/4.2 sensors, CAN communications, configurable safety and boost control. Electronic-throttle capability and ZF 8HP functions depend on the purchased hardware, firmware and compatible transmission. Confirm what is included before assuming an accessory or feature is present.
Connectors and wiring
The model sales page does not provide a verified complete ECU-to-adapter and vehicle-connector cavity schedule. Use the RM-Primis documentation and the exact adapter guide for the hardware supplied; do not transfer another BMW kit’s pinout based only on connector shape or model family.
References
RM-Primis BMW M50 and M50TU plug-in ECU manufacturer listing; RM-Primis universal platform; RM Racing Electronics index.
Adapter auxiliary connectors — BMW M50/M4x and M6x 88-pin adapter
RM Racing’s RM-Primis booklet, PDF page 16, documents the following six-way accessory connector assignments for the adapter named above. These are the adapter’s auxiliary and LSU connectors, not the factory vehicle connector and not the 32-way board-to-ECU headers shown in the drawing. The booklet gives a generic 32-way header schedule separately on PDF page 12; see the board-header tables below. Match the actual adapter board and revision before using this schedule. The booklet says the two marked high-side outputs are converted on the adapter board to ground-switching outputs; select the corresponding high-side channel in RM-Tuner. Verify installed board and output ratings before connecting any load.
LSU 4.9 wideband adapter connector
| Adapter pin | Signal | Sensor wire colour | LSU 4.9 sensor pin |
|---|---|---|---|
| 1 | H− | White | 3 |
| 2 | VS | Black | 6 |
| 3 | Rcal | Green | 5 |
| 4 | H+ | Grey | 4 |
| 5 | VS/IP | Yellow | 2 |
| 6 | IP | Red | 1 |
Auxiliary connector 1
| Pin | Manufacturer function |
|---|---|
| 1 | Spare voltage input 5 |
| 2 | Spare temperature input 2 |
| 3 | Low-side general-purpose output 4 |
| 4 | MAF / analogue voltage input |
| 5 | Digital / trigger input 2 |
| 6 | Low-side general-purpose output 5 |
Auxiliary connector 2
| Pin | Manufacturer function |
|---|---|
| 1 | High-side output 4 (converted on board to low-side output) |
| 2 | High-side output 1 (converted on board to low-side output) |
| 3 | Drive-by-wire motor + |
| 4 | CAN high |
| 5 | CAN low |
| 6 | Drive-by-wire motor − |
RM-Primis plug-in adapter board headers
The RM Racing booklet, PDF page 12, labels the RM-Primis plug-in adapter’s left and right 32-position board headers looking straight at the board. The model-specific diagrams in the booklet show the same header layout; use these tables only after matching the actual board and revision. These are board-side connector positions, not the original vehicle’s loom or ECU connector cavity numbers. Vehicle-specific adapters can route or condition signals differently; consult the model-specific auxiliary notes above and confirm the wiring before connecting devices.
Header 1 — left side of board
| Board-header position | Manufacturer function |
|---|---|
| 1 | Injector output 1 |
| 2 | Injector output 2 |
| 3 | Injector output 3 |
| 4 | Injector output 4 |
| 5 | Injector output 5 |
| 6 | Injector output 6 |
| 7 | Ignition output 1 |
| 8 | Ignition output 2 |
| 9 | Ignition output 3 |
| 10 | Ignition output 4 |
| 11 | Ignition output 5 |
| 12 | Ignition output 6 |
| 13 | Fuel pump output |
| 14 | Low-side GP 1 |
| 15 | Low-side GP 2 |
| 16 | Low-side GP 3 |
| 17 | Ground |
| 18 | Ignition-switch input +12 V |
| 19 | Permanent battery +12 V |
| 20 | LSU IP |
| 21 | LSU RCAL |
| 22 | LSU VS/IP |
| 23 | LSU VS |
| 24 | LSU H+ |
| 25 | LSU H− |
| 26 | Tachometer output |
| 27 | High-side GP 4 |
| 28 | High-side GP 3 |
| 29 | High-side GP 2 push-pull |
| 30 | High-side GP 1 push-pull |
| 31 | Low-side GP 5 |
| 32 | Low-side GP 4 |
Header 2 — right side of board
| Board-header position | Manufacturer function |
|---|---|
| 1 | Throttle position sensor input |
| 2 | Coolant temperature sensor input |
| 3 | Intake air temperature sensor input |
| 4 | Digital / trigger input 1 (pull-up selectable) |
| 5 | Digital / trigger input 2 (pull-up selectable) |
| 6 | Digital / trigger Hall input (no pull-up) |
| 7 | MAF / analogue voltage input |
| 8 | Spare voltage input 1 |
| 9 | Spare voltage input 2 |
| 10 | Spare voltage input 3 |
| 11 | Spare voltage input 4 |
| 12 | Spare voltage input 5 (pedal 2 when DBW) |
| 13 | Spare temperature input 1 |
| 14 | Spare temperature input 2 (pedal 1 when DBW) |
| 15 | DBW TPS input 2 |
| 16 | 5 V output for sensors |
| 17 | DBW motor + |
| 18 | DBW motor − |
| 19 | Ground |
| 20 | Ground |
| 21 | Ground |
| 22 | 5 V output for sensors |
| 23 | CAN low |
| 24 | CAN high |
| 25 | Knock sensor 2 − |
| 26 | Knock sensor 2 + signal |
| 27 | Knock sensor 1 − |
| 28 | Knock sensor 1 + signal |
| 29 | Variable-reluctance sensor 2 − |
| 30 | Variable-reluctance sensor 2 + |
| 31 | Variable-reluctance sensor 1 − (adjustable threshold) |
| 32 | Variable-reluctance sensor 1 + (adjustable threshold) |