PnPduino Toyota 4A-GE 20V Blacktop is a PnPduino programmable engine-management ECU. Manufacturer product information.

Application and identification
Manufacturer identifies this plug-in as being for the Japanese-market Toyota 4A-GE 20-valve Blacktop. Confirm the exact original ECU and loom; the product description does not establish that the Silvertop pinout is interchangeable.
System and wiring
A VR conditioner is intended for the original distributor without modification. High-impedance aftermarket injectors are specified and the stock MAP sensor is used. Bluetooth uses Serial 3 from version 4; STM32 is offered from version 5 for CAN and SD logging.
The manufacturer identifies the connector functions in diagrams but says this Toyota connector has no pin numbers. The layouts and label key are transcribed below without inventing cavity numbers.
Software and calibration
The supplied base map is described as incomplete and needs final tuning. The listing specifies official Speeduino firmware and SpeedyLoader INI, and requires a separate wideband controller.
See the PnPduino manufacturer index.
Model-specific wiring document
The manufacturer labels functions on the 26-, 16- and 22-position connectors, viewed at the front of the male ECU. It says this Toyota pinout is not numbered; do not invent cavity numbers from the ordering of its function list. Open the PnPduino pinout document. The manufacturer drawing identifies functions but does not number individual cavities.
Manufacturer connector layouts — unnumbered
The PnPduino 4A-GE 20V pinout states that its diagrams are viewed from the front of the 64-pin male connector and that this Toyota connector does not have pin numbers. In each table, read cells left to right exactly as depicted; the table does not create pin numbers. Red means the manufacturer marks a position not used by PnPduino; green means a PnPduino addition. Unlabelled cells remain unlabelled.
26-way connector, front of male ECU
| Top row, left to right | PG | INJ1 | INJ4 | IDL1 | IDL2 | HT | IG3 | IG4 | G2 | NE | IGF | 12V | 12V |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bottom row, left to right | PG | INJ2 | INJ3 | X | LC3 | LC2 | IG1 | IG2 | G1 | G− | FAN | GRND | GRND |
16-way connector, front of male ECU
| Top row, left to right | VF | X | O2 | KNK | ECT | IAT | MAP | 5V |
|---|---|---|---|---|---|---|---|---|
| Bottom row, left to right | VVT | CANH | CANL | X | FLEX | TPS | EVP/LC1 | GRND |
22-way connector, front of male ECU
| Top row, left to right | STA | AC1/INP2 | VSS | TACH | INP6 | INP4 | W/LC4 | INP1 | Unlabelled (green) | FAN2 | BATT |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Bottom row, left to right | X | ACT | CLUTCH | Unlabelled (red) | INP7 | INP5 | INP3 | Unlabelled (red) | FP | BOOST | 12V |
Manufacturer label key
| Diagram label | Manufacturer description |
|---|---|
| PG | Power ground for wideband |
| INJ1–INJ4 | Injector outputs; see firing-order note |
| IDL1 / IDL2 | Idle valve RSO / RSC |
| LC1–LC4 | Programmable low-current outputs |
| HT | OEM oxygen sensor heater; not used |
| IG1–IG4 | Ignition outputs; see coil-on-plug note |
| G2 | Second cam signal; not used |
| G1 | First cam signal; source says connected to VR1− |
| NE | 24-tooth cam signal; source says connected to VR1+ |
| G− | Cam ground; source says connected to VR2+ |
| IGF | Ignition feedback; not used |
| FAN | Radiator fan output |
| 12V | 12 V from ignition switch |
| GRND | ECU ground; follow the source’s grounding instructions |
| VF | Check connector; not used |
| VVT | VVT switch output |
| CANH / CANL | CAN high / low with STM32 board only |
| O2 | Oxygen sensor input |
| KNK | Knock input for future update, Arduino 21 |
| ECT | Engine coolant temperature |
| FLEX | Ethanol fuel sensor |
| IAT | Inlet air temperature |
| TPS | Throttle position |
| MAP | External MAP sensor |
| EVP/LC1 | Low-current output 1, Arduino 26 |
| 5V | 5 V sensor output |
| STA | Starter; not used |
| AC1/INP2 | Air-conditioning switch to spare input 2, Arduino A9 |
| ACT | Air-conditioning amplifier; not used |
| VSS | Vehicle speed sensor, Arduino 20 |
| CLUTCH | Clutch / launch switch, Arduino 37 |
| TACH | Tachometer output when using coil-on-plug |
| INP1 / INP3 / INP4 / INP5 / INP6 / INP7 | Spare inputs A8 / A10 / A11 / A6 / A12 / A13 respectively |
| W/LC4 | Check-engine light from low-current output 4, Arduino 29 |
| FP | Fuel pump output |
| FAN2 | Spare output, Arduino 25 |
| BOOST | Boost solenoid output, Arduino 12 |
| BATT | Constant 12 V; not used by PnPduino |
| X | The diagram marks this cavity red; red means not used by PnPduino |
The source’s injector note maps INJ1 to injector 1, INJ2 to injector 4, INJ3 to injector 2 and INJ4 to injector 3. For sequential coil-on-plug it maps IG1 to COP1, IG2 to COP3, IG3 to COP4 and IG4 to COP2. Confirm the actual wiring and firing order in the manufacturer document. The source says the distributor shield must connect to ECU ground, and identifies CAN only for the STM32-Mega board; follow the full source instructions for grounds and configuration.