A particulate matter (PM) sensor, sometimes called a soot sensor, can monitor particles downstream of a diesel particulate filter (DPF). The control system uses its information to help detect filter-efficiency faults. It is distinct from a DPF differential-pressure sensor, which measures pressure, and from a workshop smoke meter or particle counter.
This page describes a common resistive sensor, practical diagnosis and documented sensor examples. Designs, positions, output and service procedures differ. For the wider system see petrol and diesel emissions, diesel particulate filters, DPF pressure sensors and emissions testing equipment.
What the sensor monitors
A DPF traps particles in its porous walls. On a system with a downstream soot sensor, unexpectedly rapid or excessive accumulation of conductive particles at the sensor can be evidence that particles are passing the filter. The controller evaluates this with operating conditions and its own diagnostics; a reading alone does not establish why particles are present or precisely quantify all particles emitted. Bosch describes a sensor installed downstream of the DPF for its diagnostic function. Bosch: particulate matter sensor.
Some exhaust layouts place the sensor farther downstream, including after an SCR catalyst; the precise position and additional components vary. A GM low-cab-forward diesel system describes a sensor after SCR, with its own control unit and sensing element. Identify the actual exhaust layout and sensor name from the vehicle documentation. GM bulletin 16-NA-337.
How a resistive soot sensor works
In Bosch's resistive example, soot deposits on an electrode structure and conductive paths form between electrodes. The electronics evaluate the resulting electrical current over a measurement phase. A heater regenerates the sensor element before a measurement phase, restoring a defined starting condition. The rate and pattern of accumulation are interpreted by software in context. This is an example of sensor regeneration: it cleans the sensor element, not the DPF. Bosch operating principle.
The probe commonly has a protective tip, wiring and a control module; designs and service parts vary. In a documented GM system the assembly includes an element, heater, temperature sensing and electronic controller communicating with the engine controller. Bosch describes CAN communication on its product. Do not assume every sensor has the same network, pins, heater circuit or waveform, or that a generic analogue voltage is a direct soot measurement. Obtain the correct system diagram and diagnostic instructions. GM system description; Bosch sensor.
Sensor warm-up, a sensor-cleaning event, exhaust conditions and the diagnostic monitor's entry conditions affect whether a value is valid. A low, fixed or unavailable value at a single instant is not a universal pass or failure. Nor can a sensor-cleaning cycle be assumed to be a complete DPF regeneration or vice versa.
PM, soot, particle number and pressure are different measurements
| Measurement or device | What it addresses | Limit |
|---|---|---|
| On-board resistive soot sensor | Electrical response as conductive particles collect on the element; the vehicle uses its processed signal for monitoring. | Not a laboratory scale, universal particle counter or direct measure of soot mass stored inside the filter. |
| DPF differential pressure | Pressure difference between specified points, used with flow, temperature and ECU models. | A low or high pressure alone does not prove filtration efficiency or identify a damaged sensor. DPF pressure sensor guide. |
| Particulate mass (PM) | Mass of particulate material collected using the prescribed measurement method. | Results depend on test cycle, sampling and units; a sensor electrical value cannot simply be substituted. |
| Particle number (PN) counter | Counts particles within a specified size range and sampling method, often as concentration per volume. | Not the same as soot-sensor electrical response, opacity or mass; concentration is not directly a particles-per-kilometre result. |
| Diesel smoke meter / opacimeter | Light absorption or opacity during a specified smoke test. | Not a particle-number test, a NOx measurement or proof of filter integrity. DVSA DPF guidance. |
Common symptoms and possible causes
- Sensor, heater or communication fault: an element fault, failed heater, wiring, connector, power supply or network fault may be involved. The sensor's control unit and supply must be tested using the exact system procedure.
- DPF efficiency fault or high soot detected: an actual filter, exhaust, combustion or sensor problem may be relevant. A fault naming filter efficiency does not, by itself, condemn the sensor or the filter.
- Contamination or physical damage: deposits, oil, damage, an exhaust leak or incorrect installation can affect monitoring. Moisture and condensation may affect some designs; Hino describes condensation-related fault indications in its vehicle-specific bulletin. Do not apply that bulletin to every vehicle.
- Warning lamp or restricted operation: the cause and vehicle response depend on the code, calibration and other monitored systems. Record all relevant faults and freeze-frame data before clearing anything.
Codes and their meaning depend on the vehicle and suffix. A Volvo Trucks troubleshooting guide distinguishes sensor-element and heater codes from supply, communication and DPF-efficiency faults for its US14+OBD16 and newer systems. It is a useful example of separating fault paths, not a universal replacement rule.
Workshop diagnosis and replacement
- Identify the system: record the vehicle, engine, emissions layout, sensor position and part number, all active and stored faults, freeze-frame information and applicable service bulletins. A PM probe is not necessarily the similarly shaped NOx or temperature probe.
- Check the context: use the manufacturer's scan-tool procedure to check readiness, sensor and DPF regeneration state, exhaust temperature and diagnostic prerequisites. Compare data under the specified conditions; different positions, loads and warm-up states need not agree.
- Inspect safely: allow hot exhaust parts to cool and examine the sensor, harness, control module, connector, mounting and exhaust for damage, leaks, chafing and water ingress. Check related engine, aftertreatment and filter problems.
- Follow the fault tree: use the vehicle wiring diagram and approved equipment to test supply, grounds and communication or the element and heater only as specified. Never guess pins, energise an unknown heater or apply a universal resistance or voltage target. A DPF differential-pressure reading is a separate measurement.
- Resolve the cause and verify: if the sensor is proven faulty, fit the correct complete assembly where required. Route and secure the harness, use the specified torque and thread treatment, and perform any required initialisation, software or monitor procedure. Confirm the repair under the manufacturer's conditions; simply clearing codes does not repair the fault.
Volvo's guide warns that its ceramic element is fragile and calls for correct orientation and no lubricant on the sensor threads or tip. Other products can have different instructions: check the exact part and manufacturer procedure; do not scrape, wash, heat or apply chemicals to an element as a generic repair. Volvo Trucks PM sensor guide. Exhaust components and aftertreatment regeneration can be very hot; follow manufacturer safety instructions and use suitable exhaust extraction during running tests.
Documented sensor examples
These are historical examples from the cited manufacturer documents, not an exhaustive fitment catalogue. Market, VIN, body, engine, installation and service revisions matter. Verify the current part and any supersession against the manufacturer's vehicle-specific parts information before ordering. A campaign kit may include a sensor and other items rather than being a bare sensor.
| Part reference | Documented example | Source and limits |
|---|---|---|
| BMW 13 62 8 517 184 | Selected North American F25 X3 xDrive28d, F30 3 Series sedan and F31 wagon with N47T engine, production through September 2014. | BMW SI B13 02 14; refer to the specific bulletin and VIN. |
| Ford JC3Z-5L239-A | 2017–2018 F-Super Duty 6.7 L diesel, chassis cab 166-, 168-, 193- or 205-inch wheelbase. | Ford TSB 18-2225, US bulletin for specified vehicles built on or before 9 July 2018. Different body and wheelbases have different listed numbers. |
| Ford JC3Z-5L239-B | Same bulletin: chassis cab 145-, 179- or 192-inch wheelbase. | |
| Ford JC3Z-5L239-C | Same bulletin: pickup. | |
| GM 40009127 | 2023 Chevrolet Silverado and GMC Sierra with 3.0 L LZ0 diesel, North America. | GM PIP5878A; GM instructs use of VIN and its parts catalogue to identify the correct part. |
| Nissan 227A3-EZ41B / Cummins 5461551 | PM sensor in a documented Nissan retrofit kit for certain 2016–2017 Titan XD 5.0 L Cummins diesels. | Nissan NTB24-061 lists those component cross-references within kit 22793-EZ41A. Campaign eligibility is vehicle-specific. |
| PACCAR 2160125MXC, 2160127MXC or 2160128MXC | Different sensor references in a recall for certain EPA 2021 MX-11 and MX-13 equipped Peterbilt chassis built June–September 2021. | PACCAR E285 requires matching the sensor to the identified chassis; the three numbers are not asserted interchangeable. |
UK MOT and emissions testing
The DVSA MOT inspection manual, section 8 sets the applicable emissions equipment, malfunction-indicator and smoke checks and exemptions. Do not assume the routine MOT includes a dedicated on-board PM-sensor accuracy test or a particle-number count. A smoke-opacity pass does not establish the sensor's accuracy, filter integrity in every condition, or the vehicle's driving-cycle emissions. Test methods and rules can change; consult the current manual.
Sources and related reading
- Bosch Mobility, particulate matter sensor — resistive electrodes, cleaning cycle, DPF monitoring and a CAN-connected example.
- GM 16-NA-337 — one diesel system's PM sensor and aftertreatment layout.
- Volvo Trucks PM sensor troubleshooting guide — installation handling and fault distinctions for specified systems.
- DVSA DPF guidance; MOT manual section 8.
- DPF differential pressure sensors; emissions testing equipment.