Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

MSPNP2 ECU product illustration
Manufacturer MSPNP2 product photograph used as a family illustration; vehicle-specific connectors and casing can differ. Image: AMP Engine Management; reproduced with permission.

MSPNP2 EEC4A8 is a vehicle-specific MegaSquirt-II-based plug-in ECU. The manufacturer’s documentation lists 1987–1993 Mustang 5.0L and 1986–1988 Thunderbird 5.0L. Confirm the ECU part number, engine, harness, region and transmission before use.

Application and version

The manufacturer’s index marks this MSPNP2 variant obsolete; do not infer current stock. This page describes the manufacturer’s version 2.0 documentation. Different hardware versions, optional jumpers and configurations can change installation details.

Installation and pinouts

Refer to the EEC4A8 version 2.0 installation guide for its model-specific wiring diagrams, connector orientation, sensor configuration and setup instructions. Check the exact installed configuration; avoid applying the pinout of an MS3Pro PNP or another vehicle. The manufacturer’s manual index also links older version documents.

Select and verify the correct base tune, check timing as directed and tune the specific engine after installation.

Main 60-way connector — A8 V2.0

The manufacturer's A8 installation guide supplies the following pin-function table. A dash means the guide does not identify a function, not that the vehicle's cavity is necessarily empty. Check its connector face and jumper settings for the exact unit.

PinECU functionUsage / note
112 V batteryConstant supply
2——
3——
4——
512 V ignitionIgnition switch
6Power groundGround
7CLTCoolant temperature sensor
8——
9——
10A/C statusA/C idle up; see JP2
11——
12INJAInjector 3
13INJAInjector 4
14INJBInjector 5
15INJBInjector 6
16Power groundICM ground
17CELCheck engine lamp
18——
19——
20Power groundGround
21IACIdle valve
22Fuel pumpFuel pump relay
23——
24——
25IATIntake air temperature sensor
265 V referenceSensor supply
27——
28——
29O2 sensor, rightSee jumper J5
30Clutch switchLaunch control
31——
32——
33——
34——
35——
36SPOUTSPOUT signal to ignition driver
3712 V ignitionIgnition switch
38——
39——
40Power groundGround
41——
42INJBInjector 7
43O2 sensor, leftSee jumper J5
44——
45External MAPOptional external MAP sensor; see JP4
46Sensor groundSensor return
47TPSThrottle position sensor
48——
49Power groundGround
50——
51——
52INJBInjector 8
53——
54——
55——
56PIPPIP signal from ignition driver
5712 V ignitionIgnition switch
58INJAInjector 1
59INJAInjector 2
60Power groundGround

Rear 26-way options connector — A8 V2.0

PinFunctionManufacturer note
AAnalogue sensor groundSensor return
BPower ground
CEGOJ5 jumper must be removed
DKnock (ADC2)
EIATDuplicated on main connector pin 25
FExternal MAP sensorJP4 to EXT; default internal MAP
GCAN low
H5 V DC output
ICAN high
J12 V supply outputFused at 500 mA
KTable switch input
LVRIN2+Optional cam sensor input
MLaunch input
NClutch inputConnects to launch input via JP16
OTachometer output
POutput 2
QOutput 1
RBoost
SIgnition DOptional wasted spark: cylinders 2 and 8
TInjector BHigh impedance only
UIgnition COptional wasted spark: cylinders 4 and 7
VInjector AHigh impedance only
WIgnition BOptional wasted spark: cylinders 3 and 5
XInjector BHigh impedance only
YIgnition AOptional wasted spark: cylinders 1 and 6
ZInjector AHigh impedance only