
MSPNP-Pro MM9697 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1996–1997 Mazda Miata 1.8L with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
Use the 1996–1997 vehicle harness and model-specific jumper documentation. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI MM9697 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.
Rear options connector — A–Z
From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.
| Pin | Function | Default or note in source |
|---|---|---|
| A | Sensor ground | — |
| B | Knock sensor | — |
| C | Analog input 2 | Alternator voltage reference |
| D | Analog input 1 | MAF |
| E | IAT | — |
| F | External MAP sensor | — |
| G | CANL | — |
| H | +5 V reference | — |
| I | CANH | — |
| J | +12 V ignition out | Maximum 0.5 A |
| K | Digital frequency in 3 | — |
| L | Digital frequency in 2 | VSS |
| M | Digital in 1 | Flex |
| N | Digital in 2 | Clutch signal |
| O | Digital in 4 | — |
| P | High current 1 | VVT |
| Q | High current 3 | Nitrous |
| R | High current 2 | Boost control |
| S | Ignition D logic level | — |
| T | Injector H | High Z or GPIO only |
| U | Ignition C logic level | — |
| V | Injector G | High Z or GPIO only |
| W | Ignition B logic level | — |
| X | Injector F | High Z or GPIO only |
| Y | Ignition A logic level | — |
| Z | Injector E | High Z or GPIO only |
Vehicle and optional connector assignments
From the AMP EFI MM9697 application guide. Connectors 1, 3 and 4 are labelled factory wiring; connector 2 is optional wiring. “N/C” reproduces the guide’s label; check connector orientation, harness and jumper settings in the original.
Connector 1
| Pin | Function from guide |
|---|---|
| 1A | Fan 1 relay (PWM2) |
| 1B | A/C relay (Injector J out) |
| 1C | N/C |
| 1D | N/C |
| 1E | CEL (via DFIN1) |
| 1F | N/C |
| 1G | A/C relay (Injector J out) |
| 1H | N/C |
| 1I | N/C |
| 1J | N/C |
| 1K | A/C switch in |
| 1L | Clutch switch (digital in 2) |
| 1M | VSS (DFIN2) |
| 1N | N/C |
| 1O | Ground |
| 1P | N/C |
| 1Q | N/C |
| 1R | N/C |
| 1S | N/C |
| 1T | N/C |
| 1U | Fuel pump relay |
| 1V | N/C |
Connector 2
| Pin | Function from guide |
|---|---|
| 2A | CANH |
| 2B | Oxygen sensor |
| 2C | CANL |
| 2D | Tach out |
| 2E | External MAP sensor |
| 2F | Knock sensor |
| 2G | Ground |
| 2H | CMP (cam) signal |
| 2I | PWM3 (alternator field) |
| 2J | CKP (crank) signal |
| 2K | AIN2 (alternator voltage reference) |
| 2L | High current 2 (boost) |
Connector 3
| Pin | Function from guide |
|---|---|
| 3A | N/C |
| 3B | N/C |
| 3C | Front O2 sensor (via J5) |
| 3D | Rear O2 sensor (via J5) |
| 3E | N/C |
| 3F | TPS |
| 3G | CLT sensor |
| 3H | N/C |
| 3I | Vref |
| 3J | N/C |
| 3K | IAT sensor |
| 3L | Ground |
| 3M | O2 sensor heater ground |
| 3N | N/C |
| 3O | Sensor ground |
| 3P | N/C |
Connector 4
| Pin | Function from guide |
|---|---|
| 4A | Ground |
| 4B | +12 V ignition |
| 4C | Ground |
| 4D | Ground |
| 4E | N/C |
| 4F | CKP (crank) signal |
| 4G | CMP (cam) signal |
| 4H | N/C |
| 4I | N/C |
| 4J | N/C |
| 4K | Condenser fan (Injector I out) |
| 4L | Tach out |
| 4M | N/C |
| 4N | Cylinder 1/4 ignition coil (Ignition A out) |
| 4O | N/C |
| 4P | N/C |
| 4Q | IAC (PWM1) |
| 4R | Cylinder 2/3 ignition coil (Ignition B out) |
| 4S | N/C |
| 4T | N/C |
| 4U | Cylinder 1 injector (Injector A out) |
| 4V | Cylinder 2 injector (Injector D out) |
| 4W | Cylinder 3 injector (Injector B out) |
| 4X | Cylinder 4 injector (Injector C out) |
| 4Y | N/C |
| 4Z | N/C |