
MSPNP-Pro B8793 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1987–1993 BMW 325 E30 with M20 engine. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
The E30 application is distinct from the E36 versions; match the chassis and wiring. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI B8793 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.
B8793 main connector — 55 positions
Transcribed from the AMP EFI B8793 installation and connector guide. A dash reproduces a blank in that guide; it does not prove a factory wire or terminal is absent. JP1 changes A/C request assignment. Check the guide's connector orientation, actual harness and model before wiring.
| Pin | MS3 I/O function | Usage |
|---|---|---|
| 1 | Ignition A | Ignition coil |
| 2 | PGround | Power ground |
| 3 | Fuel Pump | Fuel pump relay |
| 4 | PWM1 | IAC open |
| 5 | — | — |
| 6 | Tach Out | Tachometer |
| 7 | — | — |
| 8 | CMP+ | Spare I/O |
| 9 | — | — |
| 10 | PGround | Power ground |
| 11 | Knock1 | Knock sensor |
| 12 | 5V Vref | Sensor +5 V supply |
| 13 | — | — |
| 14 | PGround | Power ground |
| 15 | Injector H | CEL |
| 16 | Injector B | Injector bank 1 (cyls 1, 2, 5) |
| 17 | Injector A | Injector bank 2 (cyls 2, 4, 6) |
| 18 | — | Constant 12 V battery supply |
| 19 | PGround | Power ground |
| 20 | — | — |
| 21 | — | — |
| 22 | PWM2 | IAC close |
| 23 | High Current 1 | Spare I/O |
| 24 | PGround | Power ground |
| 25 | — | — |
| 26 | SGround | Sensor ground |
| 27 | — | Ignition switch 12 V supply |
| 28 | O2 | Oxygen sensor input |
| 29 | DFIN3 | Vehicle speed sensor input |
| 30 | PGround | Power ground |
| 31 | CMP− | Spare I/O |
| 32 | PWM3 | Fuel rate output |
| 33 | Injector F | Spare I/O |
| 34 | Injector D | Spare I/O |
| 35 | Injector C | Spare I/O |
| 36 | — | Main relay coil activation |
| 37 | 12V Supply | Main relay contacts |
| 38 | — | — |
| 39 | — | — |
| 40 | DI3 (set by JP1) | A/C request (pre-1988) |
| 41 | DI3 (set by JP1) | A/C request (1988+) |
| 42 | — | — |
| 43 | — | — |
| 44 | IAT | Intake air temperature sensor |
| 45 | CLT | Coolant temperature sensor |
| 46 | — | — |
| 47 | CKP+ | Crankshaft position sensor + |
| 48 | CKP− | Crankshaft position sensor − |
| 49 | — | — |
| 50 | — | — |
| 51 | — | — |
| 52 | TPS | Throttle position sensor |
| 53 | TPS Vref | TPS Vref |
| 54 | — | — |
| 55 | — | — |
Rear options connector — A–Z
The source requires original O2 sensors disconnected when the optional wideband input is used. Some I/O duplicates main connector functions; do not assume all can be used independently.
| Pin | MS3 I/O function | Usage / manufacturer note |
|---|---|---|
| A | External MAP Sensor | Internal MAP sensor |
| B | 5V Vref | Fused at 250 mA |
| C | AIN2 | Analog In 2 |
| D | Analog Sensor Ground | Sensor return |
| E | AIN1 | Source notes 'Analog In 2'; see note |
| F | Digital Switched In 2 | — |
| G | EGO | Optional wideband O2; duplicates main pin 28 |
| H | Digital Frequency In 1 | 0–5 V square wave input |
| I | Digital In 1 | Optional flex fuel |
| J | High Current Out 2 | — |
| K | CANL | CAN low |
| L | Injector J | — |
| M | CANH | CAN high |
| N | Injector I | — |
| O | Ignition A | 0–5 V output |
| P | Injector A | Injectors 2, 4, 6; duplicates main pin 17 |
| Q | Ignition B | 0–5 V output |
| R | Injector B | Injectors 1, 3, 5; duplicates main pin 16 |
| S | Ignition C | 0–5 V output |
| T | Injector C | Duplicates main pin 35 |
| U | Ignition D | 0–5 V output |
| V | Injector D | Duplicates main pin 34 |
| W | Ignition E | 0–5 V output |
| X | Injector E | — |
| Y | Ignition F | 0–5 V output |
| Z | Injector F | Duplicates main pin 33 |
Source inconsistencies: the rear connector image labels E as AIN1 but calls its note “Analog In 2”. Its injector-bank-B note lists cylinders 1, 3, 5, while the main pin 16 table lists 1, 2, 5. Confirm both details with AMP EFI for the exact hardware.