Scope and prerequisite evidence
This guide concerns EA888 MED17.5 investigation, including a reported 2011 Volkswagen Scirocco CCZB with a K04 conversion and DSG. Identify the engine, ECU/TCU software, injector part numbers, fuel and installed patches before applying a map definition. Begin with the fuel-pressure and lambda checks; a pressure trace alone cannot establish available injection time.
Throttle closure and misfire: a case with a retracted fix
The CCZB throttle/misfire case initially attributes throttle closure to several possible causes, and certainty about an injection-window diagnosis was later withdrawn. On page two, an apparent fix involving pressure-ratio/load limiting is retracted: the improvement occurred on one run and did not persist. Using an injection-time number without engine speed was also challenged. The last visible exchange continues the investigation rather than establishing a completed repair.
The public case does not validate a universal pulse-width ceiling, lambda target or change to a pressure-ratio limiter. Nor does a retracted explanation establish the opposite diagnosis, so the competing explanations and the observations that could distinguish them should be kept.
A manufacturer reference for timing and control state
The Bosch reference is a work-in-progress EA888 ULEV document dated 18 July 2007, project D175X56H_M08C0;2. It is not a matched definition for the CCZB car.
Its AWEA section treats B_enimbgr as an enable for injection-angle torque-limit regulation. HO1 injection advance has a boundary, KFWBHO1SMX. An enabled controller alone does not prove binding delivery capacity. Bosch AWEA 27.80.1, pp. 1644–1647.
KLSWBHTKR is an injection-start correction temperature threshold in that reference. Its role should be verified before it is treated, as the forum case does, as a component-enrichment map. AWEA parameter definitions.
Duration must be related to engine speed and the active event
For a constant-speed calculation, crank degrees = 0.006 × rpm × duration in milliseconds. An illustrative 6 ms spans 108° at 3000 rpm and 216° at 6000 rpm. These are arithmetic examples, not permitted windows. Dividing by the complete 720° four-stroke cycle does not identify which part of that cycle is available for the selected injection event.
First establish whether a channel is a diagnostic summary, an effective time, an electrical command or one event in a multiple-event strategy. Then obtain its actual start/end-angle convention and the applicable boundaries. A displayed duration should not be assumed to cover every pulse, and a larger number at low rpm does not have the same significance as a smaller one at high rpm.
| Observation | Evidence needed next |
|---|---|
| Injection-window regulation is enabled. | Compare its requested/limited torque and angle margin with the other selected limits. Determine whether it is restrictive at that instant. |
| Throttle closes while rail pressure follows request. | Follow the torque/load request path and injection timing together. Check mixture independently; rail tracking does not prove adequate delivered fuel mass. |
| Misfire or damaged plug accompanies a high-load complaint. | Preserve faults and inspect the physical fault before further loaded comparisons. A boost trace or a lack of displayed knock correction does not clear the engine mechanically. |
Injector-flow reports and cylinder corrections
Bosch's HDEV 5.2 data sheet, pp. 1–2, separately specifies static and dynamic flow tolerance, identifies dynamic test duration, and describes application-dependent spray and electrical characteristics. This illustrates why a single flow percentage is incomplete characterisation; it does not identify the injector fitted to the CCZB.
A forum question titled “MED17 Cylinder Specific Injector Corrections/Trims?” asks about bank scaling versus individual injectors and reproduces an AI-suggested map name. The public page reviewed has no corroborating reply, so KFFLTP is not verified as an available cylinder correction in either named MED17 variant.
Test fluid, pressure difference, temperature, drive waveform, pulse duration, repeatability, leakage and spray results should be obtained for the actual part. A bank-average mixture correction cannot establish that each cylinder receives the intended fuel. Likewise, a per-cylinder output array is not proof of a corresponding user-adjustable flow constant. A physical imbalance should be investigated before an unverified definition is used to compensate for it.
Capture a comparison that can resolve the complaint
Record rpm, injection mode, event durations and angles, pressure request/actual, final lambda request/measurement, temperature state, throttle, requested/limited load and available torque contributions. Compare stable points and the onset of the fault with synchronised timestamps. Change one understood function at a time and repeat the condition; a single favourable run cannot distinguish a correction from a change in temperature or operating state.
The comparison method is editorial diagnostic reasoning from the cited evidence. No timing limit, injector scalar or protection threshold is prescribed.
Not established
- A universal pulse-width ceiling, lambda target or pressure-ratio limiter change for the CCZB.
- Availability of
KFFLTPas a cylinder correction.
Sources and related pages
Sources: the Bosch reference and data sheet above and the NefMoto reports linked in the text, reviewed 17 November 2026. The forum cars and attachments were not independently tested. MED17.5 hub · Wastegate diagnosis.