Tuning Wiki
Browse Audi
Applies to

Check the hardware and software limits stated in this article.

Scope and identification

This example covers the EA855 EVO 2.5-litre five-cylinder in Audi’s DAZA TT RS training material and the associated MED17.1.62 tuning context. Audi SSP 920273 spells the controller designation “MED 17.01.62”; EcuTek identifies MED17.1.62 for its stated 2017–2020 RS3 and TT RS applications. Identify the engine, ECU part number, software and market before using a definition or assuming another 2.5 TFSI has the same system. Audi SSP 920273, pp. 1–3 and 46–51; EcuTek EA855 tuning guide.

Two injection paths, several operating modes

The documented engine has a low-pressure rail supplying intake-manifold injectors and a high-pressure rail supplying direct injectors. Audi describes the FSI system as designed for up to 250 bar and the MPI system as rated at 7 bar; these are system ratings, not target pressures for a tune. It identifies sensors for both fuel-pressure circuits. Establish the pressure reference, units and actual operation before interpreting a log.

Both sets of injectors do not necessarily deliver fuel at every operating point. Audi lists single- and dual-phase high-pressure injection as well as combined MPI/FSI operation, with starting examples that use FSI. Record the active mode and, where available, the commanded split before attributing a mixture error to either circuit. Hardware, injector characteristics and calibration details can vary by application. Audi SSP 920273, pp. 46–49.

Trace the request and observe the result

EcuTek describes a torque-based request path in its EA855 example: driver demand and limits feed a cylinder-fill request, which is converted through the air and pressure model. Its guide distinguishes slower air-path responses from faster torque actions such as ignition and fuel control. Map selection can depend on operating mode, flap, valve-lift or cam state. Confirm the active calibration and conditions before comparing target and actual values. EcuTek EA855 tuning guide.

Build a baseline with the available request and measured signals: lambda, fuel pressures, load or air charge, manifold and pre-throttle pressures, wastegate request and response, temperatures, ignition and per-cylinder knock correction. Include injection mode or split if the logger exposes them. Record fault and adaptation state, fuel, hardware and conditions. A fuel-trim error alone does not identify which injector circuit or sensor is responsible.

Sensor locations in Audi’s example. SSP 920273 identifies G410 as a low fuel-pressure sensor and G247 as a fuel-pressure sensor on the high-pressure system. Its system overview also lists G71 for manifold absolute pressure and G31 for charge-air pressure. Confirm the actual logger labels, units and pressure reference for the vehicle, then compare each available request with the measurement at the same location and operating state. Audi SSP 920273, pp. 46 and 50.

Using MxT as a reference

The MxT MED17 guide discusses dual-injection, torque and log-analysis workflows. The project’s README classifies its MED17 support as beta. Check any suggested maps, formulas and assumptions against the exact ECU definition, Audi’s engine information and independent measurements; the guide’s broad descriptions should not be applied to every MED17. Keep component-protection and diagnostic functions understood when reviewing a change.

MxT workflow context is adapted and rewritten from TracqiTechnology/MxT contributors; Apache License 2.0, full text.

Modified software and switching. The MxT MED17 guide describes special handling for scalar definitions and multiple switched ignition maps in some aftermarket DS1 workflows. Treat these as tool and modified-software examples, not proof of a universal factory map layout. A one-cell definition alone does not establish which patch or strategy is installed. Identify the software, enabled map switch, fuel blend and operating mode before comparing logs or proposed values. MxT MED17 Calibration Guide.

This tool-specific note is adapted and rewritten from TracqiTechnology/MxT contributors’ MED17 guide; Apache License 2.0, full text.

Related pages

Bosch MED17.1.62 · Volkswagen Group EA855 R5 engines · Mixture tuning: AFR and lambda · Engine knock