Tuning Wiki
Browse Maserati

This page adds hard figures and identification leads to the Biturbo pages. Figures are secondary-source specification data, so verify them against the car and the workshop manual. Where sources disagree, both values are given.

Baseline 2.0 litre carburettor Biturbo

ItemFigure
Capacity and layout1,996 cc, 90° V6, light-alloy block and heads, wet liners
Bore and stroke82 × 63.5 mm in this source (63 mm in two others)
Compression ratio7.8:1; one source says the S versions rose from 7.4:1 to 7.8:1
ValvesThree per cylinder (two inlet, one exhaust), 18 in total
FuelOne twin-barrel downdraught Weber carburettor, electric fuel pump
TurbochargingTwo IHI turbochargers, one per bank; boost not stated in this source
IgnitionElectronic
Output180 hp (DIN) at 6,000 rpm; 255 N·m at 3,500 rpm; redline 6,400 rpm
TransmissionZF five-speed manual, 3.73 final drive; ZF automatic optional
ChassisMacPherson struts at the front, independent rear, anti-roll bars at both ends, dual-circuit disc brakes
WeightAbout 1,086 kg

Other compression figures quoted for later engines include 8.1:1 for the 4.18v and 7.6:1 for the 2.24v; a 9.0:1 figure appears on one page and conflicts with the rest. Valve-train descriptions also differ between sources (single or double overhead camshafts per bank on the three-valve engine). The 2.5 litre engine is given as 2,490.9 cc with a 91.6 × 63 mm bore and stroke in one source.

Power-figure conflicts

  • The 420i is given as 185 PS in one table and 190 hp in another.
  • The 222 4v and 430 4v are 279 or 280 PS depending on the source.
  • The 1986–87 Spyder i is listed at 185 hp and the 1987–88 Spyder i at 195 hp in one specification set.
  • Catalyst-equipped cars of the same model are consistently listed 20–25 PS lower; a Swiss/US catalyst 2.5 ES is given as 194 PS against 205 PS for the standard car.

Carburettor, injection and MABC: where sources disagree

TopicStatements found
Carburettor typeWeber 36 DCNVH 16/100 (specification sheets); Weber DCNVH on the 1984–85 2.5; "42 DCNVH" in a German-language encyclopaedia entry; Weber 34 DAT on 1986 2.5 litre cars. The size is unconfirmed, so identify the carburettor from its plate.
Start of injection1986 for the Biturbo i and Si and the 420i (most sources). One source describes Weber multipoint port injection from 1986 and Magneti Marelli digital injection replacing it in 1987; another says all engines moved to multipoint injection from 1987.
Date MABC arrivedJune 1983 in specification sheets; 1984 on all versions in an Italian-language entry. The 1984 Biturbo S is described as using an intercooler to allow higher boost.
Origin of the 3-valve headDescribed as derived from the two-valve Merak V6 in one entry.

ECU identification leads

  • An aftermarket ECU software database lists Magneti Marelli IAW entries for the Ghibli (V6 turbo, including a 2.0 litre 283 CV listing) and the Shamal 3.0/3.2 V8 turbo. Its hardware and software fields are blank, so these confirm the IAW family but not part numbers.
  • The same database shows a Quattroporte or Ghibli 2.8 V6 ECU with a 27C256 EPROM and a 3200 GT V8 ECU with a 29F400 flash chip. Those chip types are indicative of later cars and should not be assumed for the early Weber-Marelli Biturbo units.
  • No listing was found for the carburettor-era cars, the Biturbo i/Si, 222, 228 or 430.
  • Marelli IAW ECUs from other manufacturers (for example the Fiat Coupé 2.0 turbo) share the family name but are not interchangeable data sources.

Carburettor fitment

A Maserati parts supplier lists one idle jet as fitting the Weber DCNF (GT models), the DCNVH and the DAT, all for Biturbo applications, which supports the DCNVH and DAT fitment recorded on the fuelling and ECU page. Generic Weber float-level and jetting charts exist for ICH, ICT and DCOE carburettors, but they do not carry over to the DCNVH or 34 DAT; no Biturbo-specific figures were found.

Quattroporte IV service intervals

  • The V6 and V8 are both described as having a timing belt and a timing chain.
  • Belt: every 36,000 miles or three years, whichever comes first.
  • Chain: after about 50,000 miles; this is an engine-out job.
  • Both engines are regarded as fundamentally sound if properly maintained. Window regulators and structural corrosion on UK cars are the other flagged items.

These intervals are for the Quattroporte IV only and should not be applied to the earlier Biturbo V6, which has its own belt schedule (see faults and repair).

Further reported faults and cautions

  • Heat and fires: early catalyst cars sold in North America were prone to fires because the converter was poorly insulated, and synthetic rubber exhaust mounts overheated; the problem was corrected within a few years.
  • Hot starting: carburettor cars are prone to hard hot starts; injected cars from 1986 are regarded as largely dependable.
  • Turbo care: oil coking in the turbochargers follows hard driving without a cool-down, so a proper warm-up and cool-down routine and frequent synthetic oil changes are advised.
  • Chassis and body: bulkhead rot beneath the bonnet hinges is costly or uneconomic to repair; fuse boxes have weak conductor boards; injected cars have ventilated front discs and six track rod ends, four of which wear quickly.
  • Shamal: a differential that can crack at its chassis adjustment points, leaking radiators and failing alternators are reported, one cracked cylinder head has been described, and a cam belt of unknown age should simply be replaced.
  • Early-build quality: the first three production years are associated with rust, electrical defects and rushed testing.

Diagnostic manual

The Maserati Club archive lists a 55-page Weber/Magneti Marelli IAW troubleshooting manual (AUTODIAGNOS, Multi-Tester) said to cover the 1989–93 4.24v. It describes reading and clearing fault messages, throttle potentiometer identification, static and throttle tests and checks of the lambda sensor, battery and air temperature sensor. It is described as general rather than Maserati-specific. A second copy of the manual on a Fiat enthusiast site could not be opened because of a certificate error.

References

Back to the Maserati Biturbo hub.