This page paraphrases the factory workshop manual's description of the injected Biturbo system (manual pages 1-11 to 1-22, as reproduced on an enthusiast site). It explains how the control units use their sensors, which matters for tuning and fault-finding. The manual covers the 18-valve injected cars; later 24-valve systems differ.
System concept
- It is a Weber speed-density system: engine speed and the density of the intake air (from manifold absolute pressure and air temperature) set the quantity of fuel metered, to match the mixture the map calls for.
- The volumetric efficiency of the engine was measured across speed and load and stored as a map in the control unit.
- Injectors (one per cylinder) are fired in a phased sequence, following the intake order, not all at once.
- For better mixture control the throttle body has two throttle valves that open progressively.
- Ignition advance is also mapped electronically. Spark is supplied through two coils (A and B) with the distributor only distributing it.
Integrated boost and knock control
- On injected cars the boost control is part of the Marelli Microplex control unit. It stores not only spark advance values but also the maximum boost pressure and the maximum vibration (knock) level.
- It controls the turbochargers' wastegate (by-pass) valves through a solenoid valve. Where traditional systems set wastegate opening with a fixed spring pre-load, here opening follows boost pressure and the control unit's demand.
- If the pressure sensor shows a boost above the value stored for the engine speed, the unit opens the by-pass valves and lowers pressure.
- If the knock sensor signal rises sharply, announcing incipient knock, the unit first retards ignition by 2°. If knock persists it retards a further 2°; if the knock has still not gone, it opens the by-pass valves to cut boost until it stops.
- The manual states this protection allows a higher compression ratio to be used for better output and economy.
Running conditions
| Condition | What the control unit does |
|---|---|
| Normal warm running | Computes phase, injection point, spark advance and fuel quantity by interpolating the maps from the sensor signals. |
| Cold start | The coolant temperature sensor signals the cold engine and the mixture is enriched; once normal temperature is reached the mixture returns to normal. |
| Acceleration | The absolute pressure sensor shows a rising pressure over time and the unit adds fuel in proportion, also adjusting for engine temperature. |
| Throttle-down (overrun) | Fuel injection is cut off, which raises engine braking and saves fuel. The unit recognises this from a closed-throttle signal from the potentiometer and engine speed above 1,000 rpm. |
| Full throttle | Signalled by the throttle potentiometer, engine speed and manifold pressure; the mixture is enriched for maximum torque. |
Sensors and actuators
| Part | Function (as described in the manual) |
|---|---|
| Injectors (6) | Open or closed only, driven by electrical pulses; quantity depends solely on pulse duration. They cannot be repaired and must be replaced. |
| Fuel pressure regulator | Sits inside the air filter box and varies fuel pressure with boost pressure. It is factory calibrated and cannot be adjusted; a faulty one is replaced. |
| Solenoid air valve | Varies air (and mixture) for cold starting and warm-up and holds idle speed at the value stored in the control unit regardless of loads such as air conditioning or the rear-window heater. |
| Absolute pressure sensor | Mounted on the intake manifold, factory calibrated and not adjustable. Used with the air temperature signal to calculate air density, so the mixture stays right at any altitude. |
| Air temperature sensor | NTC resistor in a metal body on the intake manifold; resistance falls as temperature rises. |
| Water temperature sensor | NTC resistor on the cooling circuit thermostat; used for cold-start enrichment and warm-up. |
| Throttle body | Has a bypass air channel with an idle adjusting screw; a second screw behind a plug is factory set and must not be disturbed. |
| Throttle potentiometer | Reports closed, part-open or fully open throttle; used for cut-off and full-load enrichment. |
| Crankshaft sensor | Near the pulley on the crankshaft; gives engine speed and top dead centre. |
| Camshaft sensor | Near the pulley on the right camshaft; gives camshaft position (phase) to the injection unit. |
| Knock sensor | Detects vibration for the ignition and boost control. |
Mounting modification for early cars
On injected cars with engine numbers below 051152 the factory moved the absolute pressure sensor to a new support plate (old plate 31.37.20.311, new 31.37.20.328) to improve its function. The kit (31.37.20.001) includes the plate, two screws, two lock nuts and four washers: unplug the sensor and its rubber tube, remove it with its plate, fit the new plate to the cover, turn the sensor 180°, tighten, and reconnect the connector with its terminals in the right position and the tube.
Wiring diagram component list
The manual's electronic ignition and injection wiring diagram numbers its components as follows: 1 electronic ignition control unit; 2 its connector; 3 SEM solenoid valve; 4 coil A; 5 V.A.E. solenoid valve; 6 throttle potentiometer; 7 water temperature sensor; 8 camshaft sensor; 9 crankshaft sensor; 10 air temperature sensor; 11 absolute pressure sensor; 12 electronic injection control unit; 13 test connector; 14 fuel pump and V.A.E. relay; 15 electro-injector and ECU relay; 16 crash circuit breaker (inertia switch); 17 injectors; 18 fuel pump; 19 feed from the air conditioning control; 20 refrigerant gas filter; 21 coil B; 22 air-conditioning compressor; 23 fuse box; 24 ignition switch; 25 battery; 26 camshaft sensor; 27 crankshaft sensor; 28 knock sensor; 29 Unitest connector; 30 warning lamp for lambda probe malfunction. The diagram's pin numbers are not legible enough to transcribe.
References
Related: fuelling and ECU, part numbers, MABC boost control, Maserati Biturbo hub.