Land Rover used the LT230 in several 90/110 and Defender, Discovery I and II, and Range Rover Classic applications. The casing serial number identifies the original specification of the box. A replacement unit or a regear can change what is fitted, so use the physical unit as your starting point.
Factory high-range ratios and applications
A ratio of 1.410:1 means the input turns 1.410 times for each output turn with both outputs turning together. A 1.211 box gives taller high-range gearing than a 1.410 box. With the same tyres, axle ratios and main gearbox gear, changing from 1.410 to 1.211 reduces engine speed at a given road speed by about 14%. The table is for high range. Land Rover lists 3.32:1 low range for the documented Discovery II LT230SE. Land Rover Discovery II workshop manual, LT230SE description
| High range | Serial prefix | Documented applications |
|---|---|---|
| 1.003:1 | 14D, 26D | Range Rover Classic 3.5 V8 with three-speed automatic |
| 1.192:1 | 15D, 27D, 29D | Early five-speed Range Rover Classic (15D) and five-speed V8 90 (27D, 29D) |
| 1.211:1 | 36D, 37D | Later Discovery I, including US and Japanese examples |
| 1.211:1 | 38D, 40D, 59D | Defender 90 special applications including 50th Anniversary (38D) and North American V8 examples (40D, 59D) |
| 1.211:1 | 41D, 42D, 61D, 62D, 68D, 69D, 70D | Discovery II. Centre-lock hardware and controls vary |
| 1.211:1 | 80D, 81D | Defender 90 and 110 TDCi |
| 1.222:1 | 28D, 32D | Range Rover Classic V8 and early Discovery I (28D), North American Range Rover Classic (32D) |
| 1.410:1 | 13D, 22D, 25D | Selected early 90/110, including Tdi applications (22D) and five-speed V8 110 (25D) |
| 1.410:1 | 34A, 43D, 57D | Discovery I MPi (34A) and Defender 90/110 Td5 (43D, 57D) |
| 1.667:1 | 12D, 20D, 21D, 47D | Early naturally aspirated 110 applications |
Use the application column as a guide to likely factory fitment. Some Range Rover Classics used a different transfer box. Ratio labels such as “1.2” can refer to more than one gearset. Ashcroft LT230 prefix and ratio reference · Ashcroft gearset compatibility reference
Find the serial number on the fitted unit
- Clean the machined stamping area on the lower casing towards the rear, near the transmission handbrake drum where fitted. Compare with the serial-location illustration for the unit. Photograph any ratio sticker as a second clue.
- Record the full stamped serial, including the prefix and the final suffix letter. For example, a number starting
22Dpoints to a nominal 1.410 high range. The suffix and sometimes the number within the series matter when choosing parts. - Check the actual centre-lock hardware and linkage. Discovery II units share the 1.211 ratio across several versions. A ratio or a high/low lever alone gives insufficient information about the lock mechanism or its controls.
Ashcroft serial-number location and compatibility notes · Land Rover Discovery I workshop identification drawings
Check the ratio when the stamping is missing or the box was rebuilt
On a securely supported, removed unit, select high range. Engage the centre lock where fitted, or turn both output flanges together at the same speed and in the same direction of shaft rotation. Mark the input and an output. Turn by hand and divide the number of input turns by the number of output turns. For example, ten output turns give about 14.1 input turns for a 1.410 unit. This distinguishes the main ratio groups. To separate close values such as 1.211 and 1.222, use verified gear markings or tooth counts and the correct parts reference. Aftermarket high-range sets such as 1.301 also exist. Ashcroft bench-check guidance · Ashcroft 1.301 gearset
For operation and troubleshooting, see Transfer boxes: types, common faults and the LT230.