Tuning Wiki

The parts below are the byte-wide and word-wide EPROMs that turn up in socketed engine controllers and in the device lists of the programmers built for them. Organisation and programming voltage for the ST M27C256B, M27C512, M27C1001 and M27C4001 come from those datasheets. The pin-count groups come from EVC's EPROM list. Manufacturer equivalents come from ST's February 2002 cross-reference CREPROM/0202 and from SST's base-memory cross-reference. A generic name such as 27C010 and a house name such as M27C1001 can be the same organisation and still differ in a pin. The marked datasheet wins.

Byte-wide devices

These present eight data bits. The 24-pin and 28-pin outlines were the socket in most late-1980s and early-1990s controllers. The 32-pin outline starts at 1 Mbit.

DensityOrganisationNames in the EVC list and the ST cataloguePackage the lists giveAddress pins on the ST byte-wide datasheets
32 Kbit4 K × 8273224-pin
64 Kbit8 K × 82764, 27C6428-pin
128 Kbit16 K × 827128, 27C12828-pin
256 Kbit32 K × 827256, 27C256, M27C256B, 87C25728-pin. ST also offers PLCC32 and TSOP28A0–A14. VPP is its own pin, separate from output enable
512 Kbit64 K × 827512, 27C512, M27C512, 87C51028-pin. ST also offers PLCC32A0–A15. On the DIP, pin 1 is A15 and pin 22 is GVPP
1 Mbit128 K × 827C010, 27C1001, M27C1001, 87C11032-pin. ST also offers PLCC32 and TSOP32A0–A16
2 Mbit256 K × 827C020, 27C2001, M27C2001, 87C21032-pin
4 Mbit512 K × 827C040, 27C4001, M27C400132-pin. ST also offers PLCC32 and TSOP32A0–A18. The logic diagram shows 19 address inputs
8 Mbit1 M × 827C080, 27C800132-pin in the EVC list

The M27C512 DIP drawing is the one that makes a larger device a board question. Pin 1 is A15 and pin 22 is GVPP, which is output enable and the programming supply on the same pin. The M27C256B address bus stops at A14, and its datasheet keeps the programming supply as a separate signal from output enable. A 512 Kbit part in a 256 Kbit socket works only when the board's wiring of those pins agrees with the larger device. Moates' Ostrich notes make the same point from the emulator side: unused address pins have to be held in a defined state, because the emulator and the usual software present the image at the top of the emulated space.

ST's electronic signature, read with 12 V on A9 as the datasheets specify, uses manufacturer code 20h. The device codes in the datasheets checked for this page are 8Dh for the M27C256B, 3Dh for the M27C512, 05h for the M27C1001 and 41h for the M27C4001. On the M27C512 the address pin A0 selects the manufacturer code or the device code. Those codes identify an ST part in a programmer. They do not identify the controller it was soldered into.

Word-wide devices

A 16-bit processor can use one word-wide EPROM, or two byte-wide EPROMs side by side. EVC's list puts the word-wide names on 40-pin and 44-pin outlines. ST's 2002 guide gives the size and the width. A 1 Mbit ×16 device holds 1 Mbit in total, arranged as 16-bit words, which is 64 K words. It is not a 1 Mword by 16-bit array.

ST name in CREPROM/0202Size and organisation the guide statesMacronix parts the guide maps onto it
M27C10241 Mbit, 16-bit wordsMX27C1024, and MX27C1100 in the DIP and SO columns
M27C2022 Mbit, 16-bit wordsMX27C2048, MX27C2100
M27C40024 Mbit, 16-bit wordsMX27C4096
M27C4004 Mbit, byte or wordMX27C4100, MX27C4111
M27C8008 Mbit, byte or wordNamed in the guide's ordering scheme. The Macronix mapping page was not fully extracted here
M27C16016 Mbit, byte or wordMX27C1610 is mapped to M27C160 for the 42-pin DIP in the extracted page
M27C32232 Mbit, 16-bit words

EVC also lists a 68-pin column with two entries only: CJ87BC6QG, annotated 87M12, at 512 Kbit, and CC460 at 1 Mbit. Both are outside the JEDEC DIP outline. They are recorded here because the list includes them, and they need their own datasheet before a pin or a file size is assumed from the neighbour in the table.

Low-voltage EPROMs

The M27W family in the same ST guide is the 2.7 V to 3.6 V range. The guide's examples include M27W101 for a 1 Mbit byte-wide part and M27W201 for a 2 Mbit byte-wide part, mapped from Macronix MX27L devices. A 3 V EPROM is a different supply from a 5 V M27C part. The supply letter in the ordering code is the check.

Second sources at 256 Kbit and 512 Kbit

These two densities are the ones the SST cross-reference lines up explicitly against EPROM part numbers.

DensityParts the SST table lists on the EPROM row
256 Kbit, 5 V, byte-wideSST27SF256, AM27C256, M27256, AT27C256
512 Kbit, 5 V, byte-wideSST27SF512, AM27C512, M27512, AT27C512, W27E512

SST27SF and the Winbond W27E512 are electrically erasable flash with an EPROM pinout. They are catalogued with the EPROM-pinout flash. They are in this table because the cross-reference is how a blank replacement is chosen when a windowed EPROM is no longer sold. The programmer still has to be set to the device it is actually holding. A 27C512 algorithm does not program an SST27SF512.

The overview of how these parts were used, and the controllers that published support lists name directly, is on Automotive EPROMs and EPROMs named on engine controllers.

Sources