Tuning Wiki

Jaguar Land Rover ZF 9HP48 electronic transmission controllers are identified separately from the complete gearbox. Magicmotorsport's 9HP48 TC1782F bench protocol names selected Jaguar E-Pace, Land Rover Discovery Sport and Range Rover Evoque applications; processor or gearbox name alone does not identify a single interchangeable control unit.

ZF 9HP automatic transmission
ZF 9HP automatic transmission, shown for family context; this image does not identify a specific TCM or JLR application. Image: ZF Friedrichshafen AG; user confirmed permission to republish.
Land Rover 9HP48 system component location drawing
Land Rover 9HP48 component location diagram, item 3 identifies the transmission control module. From Land Rover transmission service description, 9 July 2015, mirrored by Todo Mecánica, illustration E181074. Credit Jaguar Land Rover; reproduction permission confirmed by the user. This drawing shows an application example, not a specific TCM part number.

Identification and applications

Record the gearbox type and complete specification, vehicle VIN, production date, engine, TCM part number and diagnostic software identifier. An MHH Auto workshop discussion describes an owner-reported 2015 Evoque TCM with marking CGJ32-14C336-AA and a 2019 E-Pace unit marked CKK72-14C336-AA. That is a reported identification, not a validated interchange or parts list.

JLR's SSM73291 service communication covers certain Discovery Sport and Evoque vehicles with 9HP48 and specific fault codes; it directs checks including leaks, level and software, rather than identifying a single universal controller part number.

Programming connector evidence and unresolved discrepancy

PCMflash's module 96 connection diagram, page 7, labels a 9HP48/50 TCU example “JLR / FCA”; it gives the common assignments below for that documented example. The diagram does not specify a controller part number or explicitly state the connector-face orientation; use its numbered drawing together with the exact controller documentation and moulded cavity labels. These functions are transcribed from the supplier, not independently bench-tested, and are not verified for every JLR controller.

Example cavityPCMflash module 96 drawing
1Ground
5 and 9+12 V (as labelled by PCMflash)
34CAN high

CAN low is unresolved: the 2024 module 96 drawing labels cavity 47, while the older PCMflash module 81 JLR 9HP48 drawing, page 2, labels cavity 48. The documents do not explain whether different hardware or a documentation error accounts for the difference. Do not treat either value as universal: obtain the current application-specific pinout and confirm the exact module with the tool supplier before connecting. The other cavities, power sequencing, CAN termination and protection must also follow the exact tool instructions.

Programming and calibration

  • Magicmotorsport FLEX: its JLR ZF 9HP48 TC1782F protocol announcement lists connector-based bench flash and EEPROM read/write with specified licences. It does not state that every 9HP48 or part number is supported. Magicmotorsport's duplication compatibility list separately shows no solution for some JLR 9HP variants; confirm the exact current operation with the supplier rather than inferring cloning support.
  • PCMflash: its manual, module 81, lists JLR 9HP48 TC1782 flash and EEPROM read/write operations. The separate module 96 drawing applies to its 9HP48/50 example. Verify exact software, interface, access method, licence and recovery against the manufacturer. Read/write access is not itself a developed calibration.
  • JLR service configuration and programming are separate from an aftermarket tune. Follow the current vehicle-specific service procedure and preserve original identification and recoverable data when supported.

Fitting evidence

The only fitting evidence found is a single report in the MHH Auto discussion: an Evoque and an E-Pace 9HP48 control unit could communicate after cloning but appeared to differ in their internal temperature-sensor arrangement. The report does not establish a confirmed fix, so it is one unverified case, not an interchange rule. Check sensor, harness, software and complete part identity for the actual assembly before replacement.

See the ZF gearbox overview. Sources reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.