Tuning Wiki
Browse Ferrari

The supplied Ferrari F355 Workshop Manual, volume 2 contains an April 1998 355 F1 clutch and gearbox chapter. The pages are image scans; the observations below were checked visually against that chapter. They apply to the documented 355 F1 system and are not settings or diagnostic limits for the later Ferrari 360, F430 or another Selespeed controller. Check the exact vehicle, control unit and current Ferrari service information before work. Ferrari dates the launch of the 355 F1 to 1997 and describes its electrohydraulic, steering-wheel-operated gearbox in its company history.

The documented system

Ferrari's 355 F1 chapter describes a synchronised mechanical transmission and a dry single-plate clutch, with hydraulic actuators controlling clutch travel and gear selection and engagement. The driver can request shifts without a clutch pedal; the system can also choose changes in its documented automatic mode. A single dry clutch is not a dual-clutch transmission. Supplied workshop manual volume 2, printed D10 / PDF p. 11.

The chapter identifies a hydraulic power unit, gearbox and clutch actuators, clutch-position and gearbox-position feedback, pressure sensing, input-shaft and vehicle-speed information and driver or safety switches. The diagnostic section separates TCU power supply, sensor supply, hydraulic supply, starting, clutch enabling and gearbox enabling. That division is useful: an apparently similar failure to engage a gear can arise at several different stages. Manual printed D8–D9 and D51 / PDF pp. 9–10 and 52.

Symptoms and evidence

ObservationWhat the 355 F1 manual suggests checking
Display inactive or no displayed gear, pump never enabled, no response to levers or no tester connectionIts TCU-power branch lists battery and isolation-switch connection, fuse, self-supply relay, ignition and TCU supply among the possibilities. Establish supply, earth and communication with the documented test plan before replacing a controller or pump. Printed D51–D52 / PDF pp. 52–53.
Irregular or missing shifts and pump operationThe sensor-supply branch identifies the pressure transducer, throttle potentiometer and engagement/selection potentiometers among the affected components. Check the specified sensor supply, return and signal circuits with the correct diagram; an individual signal fault does not alone identify the failed part. Printed D52 / PDF p. 53.
Warning flashes, pump not enabled correctly or shifts unavailableIn its hydraulic supply branch Ferrari directs checks of pressure, pump electrical supply, relay/fuse, pressure transducer, hydraulic leaks and reservoir level. A pump running without a rising displayed pressure needs both feedback and hydraulic investigation. Printed D54 / PDF p. 55.
No crank and a gear or flashing neutral displayedThe starting branch distinguishes a steady neutral indication from a requested neutral that remains unconfirmed. Compare the indicated state and gear engagement feedback, and test the relevant starting circuit using the manufacturer's procedure. Do not bypass interlocks. Printed D55–D56 / PDF pp. 56–57.
Clutch does not operate or gear selection failsThe clutch branch checks hydraulic supply, clutch valve, position feedback and request; the gearbox branch then considers clutch enabling, selector/engagement valves and position feedback. Compare command and response under the prescribed conditions before deciding which component failed. Printed D56–D57 / PDF pp. 57–58.

Pressure and service context

In the 355 F1 diagnostic aid, the factory tester example calls for the line pressure to be between 50 and 60 bar and describes pump activation below 50 bar with cut-off at 60 bar. This is a 355 F1 workshop-manual observation, not a universal pump setting or a conclusive test of a particular vehicle; compare the exact equipment, conditions and current service plan. The 360 F1 guide cites different figures from a different manual. An unusual value can reflect a sensor or circuit fault as well as a hydraulic problem. Manual printed D54–D55 / PDF pp. 55–56.

The accumulator can store pressure after the ignition is off and the controller can operate actuators during tests. Follow the correct model-specific depressurisation, isolation and active-test instructions. Ferrari's diagnostic aid treats repair learning and checks as operation-dependent; do not apply another model's reset or a blanket touch-point value. Preserve fault codes and existing adaptation evidence before repair, then perform only the required setup and verify the original complaint.

Source: supplied local Workshop Manual F355 2-English Only.pdf, 355 F1 clutch and gearbox chapter, printed D8–D10 and D51–D57 (PDF pp. 9–11 and 52–58). The manual is not uploaded to the wiki. See Ferrari 360 F1, F430 F1 SD3 diagnosis and the F1-style gearbox overview.