Tuning Wiki

On specified Fiat Chrysler applications the 948TE nine-speed transmission uses a transmission control module (TCM) mounted externally on the gearbox. Chrysler's service bulletin 21-034-14 Rev. C documents 948TE-equipped 2015 Jeep Cherokee and Chrysler 200 applications and TCM programming. Identify the exact controller and vehicle; “948TE” identifies a transmission family, not a single interchangeable controller.

ZF 9HP automatic transmission
ZF 9HP transmission, shown for family context; the picture does not identify a specific controller or application. Image: ZF Friedrichshafen AG; permission to republish manufacturer imagery confirmed by the user.
Jeep Compass engine bay diagram highlighting the transmission control module
Jeep Compass 948TE/9HP48 service illustration: callout 1 identifies the TCM location. It is an application example, not confirmation of ES11-1029 or a specific part number. Image courtesy of Chrysler Group LLC, reproduced from the 2022 Jeep Compass service information; permission to republish manufacturer imagery confirmed by the user.

Identification and compatibility

Record the full label, OE hardware and calibration number, VIN, engine, production date, market, shifter and driveline, along with the transmission serial and specification number. FCA's wiTECH calibration report associates 05150742AC and other calibration numbers with a documented 2018 VM 2.4 L 948TE FWD application; this is an identification example, not proof of interchange among all 948TE vehicles. A published 2019 Jeep Compass service description places its TCM on the outside of the case over the differential. It may differ in other vehicles. See the ES11-1029 individual controller guide for a seller-identified FCA example. A common shape or number prefix does not prove matching firmware or wiring.

948TE connector assignments — source-specific example

The following selected pins are transcribed from the 948TE TCM table in ATSG 2016 seminar information, printed page 102, figure 3. The source provides a numbered connector illustration but does not identify a VIN, specific module part number or clearly state the face orientation. These are source-documented assignments, not an independently bench-tested pinout and not a universal connection recipe. Verify the exact numbered vehicle diagram and orientation before applying power.

TCM pinATSG 948TE example
1 and 2Control-module grounds, Z904 and Z909
5Fused control-module supply, A190
9Ignition OFF/RUN/START control output, F1
34CAN C positive, D29
47CAN C negative, D30

ATSG labels its ZF 9HP48 table separately from 948TE and gives a different signal arrangement. A separate Jeep 9HP bench reference instead reports CAN on 33/46 and a different pin-9 description; the source does not establish a compatible part number. Do not combine these assignments or assume the cause of the discrepancy. Use the matching VIN-specific wiring and programming instructions; pin 9 is not presented as an unconditional permanent battery feed.

Programming and calibration

FCA's 2014 service bulletin documents a wiTECH dealer reflash for its specified 2015 Cherokee and Chrysler 200 applications. This is a manufacturer software update, not evidence of user-editable tuning maps.

PCMflash describes selected ZF 9HP TCUs in its module 96 release notes and connector guide. Alientech KESS3 has a distributor-published 2022 Bosch ZF9HP protocol announcement listing certain Jeep, Chrysler, Dodge and Fiat applications. Microtronik's HexProg II package lists Jeep ZF 9HP and Bosch ES11-10xx controller families. Each protocol has different access and licensing requirements; confirm the actual hardware and software, supported operation, file editor, power and recovery procedure with the supplier. No cited generic listing proves support for every 05150742AC calibration.

Replacement evidence

The only replacement evidence found is a technician's 2015 Cherokee 948TE report: a replacement TCM communicated for diagnostic purposes but a wiTECH programming attempt failed, and the original module still communicated. The report does not establish a confirmed fix. It illustrates the value of recording faults and checking the specific part, power, network and programming process; it is not proof that any one component is faulty.

See ZF gearboxes and transmission control. Sources reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.