Edelbrock Pro-Flo 4 35710 Chevrolet LS: Edelbrock 35710 is a Pro-Flo 4 sequential-port kit for selected GM Gen III/IV LS applications, combining an application-specific cathedral-port Victor Jr intake, fuel rails, individual injectors, 4150-style throttle body and separate ECU. The manufacturer lists 35 lb/hr injectors and a 550 hp capability for the specified kit at its stated fuel pressure. This is a replacement intake and port-injection conversion, not a drop-on throttle-body-only EFI kit.

Selection and system layout
Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.
Wiring documentation
Use the model-specific Edelbrock source for hardware and wiring. The documented 37-1630 harness and 37-1631 branch connector references are given below; verify the harness part number and revision before applying them.
Pro-Flo 4 37-1630 main harness: ECU connector
Edelbrock’s 35710 instructions identify the main harness as 37-1630. The following 48-position schedule is transcribed from the 37-1630 drawing in Edelbrock’s Pro-Flo 4 instructions, printed page 17 (PDF page 19). Confirm the actual harness and revision; this is not the EZ-Street 30700 schedule. N/C is the manufacturer’s notation in this drawing, not proof of an unused position on other harnesses. The schematic does not explicitly state the connector viewing direction. The 35730 drawing labels both F4 CAN 1H and G4 CAN 1L as white; confirm the conductor identification against the actual harness and Edelbrock before connection.
| ECU position | Drawing signal | Illustrated wire |
|---|---|---|
| A1 | INJ 1 | LT BLUE |
| A2 | TACH OUT | BRWN/WHT |
| A3 | N/C | — |
| A4 | N/C | — |
| B1 | INJ 4 | BROWN |
| B2 | HT-LMB | BLK/BLU |
| B3 | APE | BLU/YEL |
| B4 | DIG GND | BLK/YLW |
| C1 | INJ 3 | PINK |
| C2 | IGN SW | PINK/BLK |
| C3 | IPN | BLUE/WHT |
| C4 | AIR T | YEL/BRWN |
| D1 | INJ 2 | GREEN |
| D2 | FAN 1 RELAY | BRWN/YLW |
| D3 | RT | BLU/ORG |
| D4 | ANA GND | BLK/WHT |
| E1 | IAC STEP C | GRN/WHT |
| E2 | IAC STEP B | GRN/YEL |
| E3 | RE + | BLU/RED |
| E4 | ANA GND | BLK/WHT |
| F1 | IAC STEP D | GRN/ORG |
| F2 | IAC STEP A | GRN/RED |
| F3 | COOL T | YEL/BLK |
| F4 | CAN 1H | WHITE |
| G1 | INJ 5 | DARK BLUE |
| G2 | FAN 2 RELAY | BRWN/ORG |
| G3 | TPS | GRN/BLU |
| G4 | CAN 1L | WHITE |
| H1 | INJ 8 | TAN |
| H2 | CRANK | YEL/ORG |
| H3 | MAP | GRN/WHT |
| H4 | VREF 1 | GREY |
| J1 | INJ 7 | YELLOW |
| J2 | CAM | YEL/VIOLET |
| J3 | FUEL PRESSURE | YEL/RED |
| J4 | MAIN RELAY | ORG/WHT |
| K1 | INJ 6 | VIOLET |
| K2 | N/C | — |
| K3 | N/C | — |
| K4 | N/C | — |
| L1 | OUT FUEL PUMP | TAN/WHT |
| L2 | VBATT IN | ORG |
| L3 | GND POW | BLK |
| L4 | GND POW | BLK |
| M1 | IGN 1 | WHT/VLT |
| M2 | IGN 2 | WHT/BLU |
| M3 | IGN 3 | WHT/GRN |
| M4 | IGN 4 | WHT/RED |
37-1631 injector/sensor harness branch connector
The 35813 instructions, printed page 22 (PDF page 24), show this separate 37-1631 sensor/injector harness connector. The 35710 kit documentation identifies the same harness part number. The lettered branch connector is not the ECU connector above.
| Branch position | Drawing signal | Illustrated wire |
|---|---|---|
| A | MAP | GRN/WHT |
| B | VREF | GREY |
| C | ANA GND | BLK/WHT |
| D | TPS | GRN/BLUE |
| E | FUEL PRESSURE | YEL/RED |
| F | AIR T | YEL/BRWN |
| G | COOL T | YEL/BLK |
| H | BATT POS | ORANGE |
| J | INJ 1 | LT BLUE |
| K | INJ 2 | GREEN |
| L | INJ 3 | PINK |
| M | INJ 4 | BROWN |
| N | INJ 5 | DARK BLUE |
| P | INJ 6 | VIOLET |
| R | INJ 7 | YELLOW |
| S | INJ 8 | TAN |