Edelbrock EZ-Street EFI 30700: The 30700 is a self-learning throttle-body fuel-injection kit for carburetted V8 engines with a compatible 4150-style four-barrel flange. The four injectors and throttle body replace the carburettor while a separate ECU controls fuel. A phone or tablet running E-Tuner 4 connects via Bluetooth. Edelbrock lists up to 650 hp and optional ignition timing control with the appropriate separately supplied distributor. Confirm linkage, air cleaner, sensors and high-pressure fuel delivery before conversion.

Selection and system layout
Identify the exact ECU, engine and kit part number, intake and throttle, sensor and ignition arrangement. The phone or tablet app is the calibration and monitoring interface, not the ECU. Fuel delivery, return plumbing and auxiliary components depend on the package. Consult the manufacturer documentation for the specific configuration.
Customer harness flying leads
The 30700 installation instructions, pages 5–6, identify these external harness leads. This is a colour reference, not a numbered ECU connector cavity schedule; check the correct ignition diagram and exact harness.
| Lead | Manufacturer function |
|---|---|
| Red | Battery positive |
| Black | Battery negative |
| Pink/black | Ignition-switched +12 V, powered during cranking |
| Blue/yellow | Fan 1 relay trigger |
| Brown/orange | Fan 2 relay trigger |
| Brown/white | Tachometer output |
| Blue | Auxiliary output |
| Yellow | Air-conditioning kick input |
Fan outputs trigger relays rather than powering fans directly. The fuel-pump connector and oxygen-sensor and engine-sensor leads are separate; follow the manual for their wiring and ratings.
J1 ECU chassis-harness connector
Transcribed from Edelbrock’s EZ-Street 30700 instructions, brochure 63-30700, revision 11/25, page 15. J1 is the ECU end of the chassis harness. The guide labels positions A1–M4 as shown; no connector viewing direction is specified on this schematic. Blank positions mean no signal or wire is drawn in this harness and must not be assumed electrically unused in other configurations. Abbreviations reproduce the printed drawing.
| J1 position | Drawing signal | Wire colour shown |
|---|---|---|
| A1 | INJ 1 | LT B |
| A2 | TACH OUT | BRN/WHT |
| A3 | Not labelled / no lead drawn | — |
| A4 | Not labelled / no lead drawn | — |
| B1 | INJ 4 | BRN |
| B2 | HT-LMB | BLK/BLU |
| B3 | APE | YEL/BLU |
| B4 | DIG GND | BLK/YEL |
| C1 | INJ 3 | PNK |
| C2 | IGN SW | PNK/BLK |
| C3 | IPN | BLU/WHT |
| C4 | AIR T | YEL/BRN |
| D1 | INJ 2 | GRN |
| D2 | FAN 1 RELAY | BRN/YEL |
| D3 | RT | BLU/ORG |
| D4 | ANA GND | BLK/WHT |
| E1 | IAC STEP C (IAC A-LO) | GRN/WHT |
| E2 | IAC STEP B (IAC B-HI) | GRN/YEL |
| E3 | RE+ | BLU/RED |
| E4 | ANA GND | BLK/WHT |
| F1 | IAC-A-HI | GRN/ORG |
| F2 | IAC-B-LO | GRN/RED |
| F3 | COOL T | YEL/BLK |
| F4 | CAN 1H | WHT |
| G1 | Not labelled / no lead drawn | — |
| G2 | FAN 2 RELAY | BRN/ORG |
| G3 | TPS | GRN/BLU |
| G4 | CAN 1L | GRN |
| H1 | Not labelled / no lead drawn | — |
| H2 | CRANK | YEL/ORG |
| H3 | MAP | GRN/WHT |
| H4 | VREF 1 | GRY |
| J1 | Not labelled / no lead drawn | — |
| J2 | HE2 | YEL/VIO |
| J3 | FUEL PRESSURE | YEL/RED |
| J4 | MAIN RELAY | ORG/WHT |
| K1 | Not labelled / no lead drawn | — |
| K2 | AUX OUT | BLU |
| K3 | IAC KICK | YEL |
| K4 | Not labelled / no lead drawn | — |
| L1 | OUT FUEL PUMP | TAN/WHT |
| L2 | VBATT IN | ORG |
| L3 | GND POW | BLK |
| L4 | GND POW | BLK |
| M1 | IGN 1 | WHT/VIO |
| M2 | IGN 2 | WHT/BLU |
| M3 | Not labelled / no lead drawn | — |
| M4 | Not labelled / no lead drawn | — |