Tuning Wiki
Browse Audi

Scope: longitudinal 0B5 S tronic

Identify the exact transmission, vehicle and engine, control hardware, software and tune before interpreting logs or a definition. Audi's eSelf Study Program 950143 describes a particular 0B5 seven-speed S tronic design. It is a technical reference for that design, not proof that every longitudinal S tronic variant has the same controller, calibration or torque limits.

Audi describes torque reduction during its illustrated 1–2 shift, as well as input-speed sensing used for clutch slip and pressure monitoring. Review the actual available channels and their definitions: commanded torque, engine response, clutch speed and pressure do not all measure the same thing. The absence of throttle closure by itself does not establish that engine torque was unchanged.

Reported shift complaints

Owner reports on enthusiast forums describe several unresolved shift complaints. A modified Audi 4.0T AMAX case involved a 2–3 over-rev or failed shift. An earlier related report describes improved drivability following torque-model edits without resolving the shift problem. A TCU limitation was suggested, but the later follow-up does not demonstrate a fix. These reports do not establish a numerical torque limit or a portable map change.

In a separate Macan hesitation case, slip was suspected by the owner and the log was interpreted differently by another contributor. The underlying attachment was not independently reviewed and no confirmed resolution is established. Hesitation or a difference between two differently defined torque values is not sufficient proof of clutch slip.

A cold 2–1 oscillation case includes other owners' mechatronic repair experiences; the symptoms are distinguished but no final cause is established. Hydraulic, mechanical, adaptation and temperature effects are possibilities to diagnose, not interchangeable fixes.

Start request ignored after replacement: Audi bulletin 37 17 74 / 2041242/2 describes 2010 S4 and S5 Cabriolet 0B5 examples where a second start-button/key request is needed after gearbox or mechatronic replacement, with no engine or transmission codes and the specifically listed TCM software. Audi attributes that documented combination to a possible software error. Check the exact repair and software history and current Audi guidance; neither a double-start symptom nor absence of codes proves the same cause on another car.

Documented 0B5 electrical and post-repair cases

Mechatronic circuit-board contacts: Audi TSB 35 13 10 / 2030477/3 concerns specified 2010–2012 S4 and S5 seven-speed S tronic cars with the exact combination P17D800/DFCC 8040 and/or P179D00/DFCC 8030; P174000/DFCC 8031 may also appear. It describes poor internal circuit-board contact and states oil additives can cause circuit-plate separation. The historical bulletin requires the fault and diagnostic failure-character codes to match and gives a board-repair procedure. A gearbox warning or base code alone does not establish that defect; verify the exact vehicle and current Audi diagnostics and fluid requirements before deciding on repair.

P179E00 after mechatronic or G676 replacement: Audi TSB 37 18 82 / 2051685/1 describes specified 0B5 S4, S5, RS5, S6 and S7 vehicles where a static drive-position-sensor electrical fault cannot be cleared and G676 basic setting cannot proceed after the mechatronic unit and/or sensor has been replaced. Audi identifies an ODIS–TCM communication issue for that workshop scenario. Record the repair history and follow current Audi tool and guided-test instructions; the bulletin does not show that every P179E00 is a tool problem or that an installed sensor is always sound.

Drive-position and input-speed sensor module: In a different scenario from the post-replacement tool issue above, Audi TSB 35 16 22 / 2032211/4 identifies an incorrect G676 driving-mode sensor module in certain 2010–15 S4 and S5, 2013–14 RS5 and 2013–16 S6/S7 seven-speed S tronic applications. Its listed diagnostic scenarios include particular combinations of P179E/P179F drive-position and P0715/P0716/P171F/P2765 input-speed entries. Audi requires the exact fault and diagnostic failure-character code to match; one scenario also requires P179E to have been logged first. Its historical repair replaces the sensor module and associated harness under the specified procedure. Capture the complete fault order, DFCC, status and repair history and follow current vehicle-specific diagnosis; neither P179E alone nor an input-speed code proves this module failed, and the later post-replacement ODIS communication case remains a separate possibility.

Build a matched record

  1. Record gearbox and TCU identifiers, modifications, fault memory, fluid service and relevant adaptations using the service procedure for the exact car.
  2. Capture shift request and phase, commanded and actual gears, engine speed and torque signals, defined clutch/input speeds, applicable pressures, pedal, throttle, ignition and temperatures. Time-align engine and transmission logs where possible.
  3. Compare the affected shift against a repeatable baseline at similar operating conditions. Check sensor definitions and logging rate before interpreting a brief transient; compare commanded and observed behaviour rather than assuming either proves physical slip.
  4. Investigate faults and mechanical or hydraulic condition alongside calibration. Do not copy pressure values or disable protections on the strength of a forum report.

Not established

The forum cases are owner reports, not independently verified repairs, and none establishes a confirmed cause or portable fix. Consult current Audi service information for the fitted variant. See also DQ500 shift selection; the 0B5 is a separate gearbox. Sources reviewed 17 November 2026.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.