Connector pinout
The Cosworth Pectel SQ6M uses three Deutsch Autosport connectors in place of the single 88-way connector of the SQ6: CN1 is an AS216-26PN (26 contacts, mating AS616-26SN), CN2 an AS216-35PN (55 contacts, mating AS616-35SN) and CN3 an AS216-26PA (26 contacts, mating AS616-26SA). Contact letters are case-sensitive: a, b and c are separate contacts from A, B and C, and are listed as "a (lower case)" and so on in the pin index.
CN1 carries ECU power (VBAT on L and M, ECU ground on Y, Z and a), ignition outputs IGN1 to IGN6, injector outputs INJ1 to INJ10 and PWM outputs PWM1 to PWM5. CN2 carries the sensor and communication side: twelve 12-bit analogue inputs, two thermocouple inputs with a common negative, two wide-band lambda channels, two knock inputs, two crank inputs and a cam input, ten digital inputs, RS-232, Ethernet, two terminated CAN buses, two programmable 5 V or 12 V sensor supplies and the protected sensor, digital and communications grounds; contact 46 is unused. CN3 carries a second set of power contacts (VBAT on A and B, ground on S, T and U), IGN7 and IGN8, INJ11 and INJ12, PWM6, the two full bridges and the DC-motor bridge, the eight logic-level ignition outputs and an unterminated third CAN bus.
Cosworth gives the processor as a Motorola MPC565 at 56 MHz with 5 MB of flash memory and 4 MB of non-volatile RAM (manufacturer documentation). The drawings below are pin indexes: the circular insert layout of each Autosport connector is not reproduced, so contact positions must be taken from the manufacturer drawing or the connector maker's insert arrangement.
The CN1 table words its driver ratings as clipping voltages (IGBT 450 V, injector drivers 45 V), while the CN3 table gives 400 V and 100 V; both are reproduced as published. Confirm the exact hardware and software revision before wiring.
Sources
- Cosworth, Pectel SQ6M ECU, product information 29E-071520-5E, pages 1–6 (processor, connector identification and pin information), copy hosted by RB Racing. Manufacturer documentation. Accessed 19 November 2026.
Connector pinout
Cosworth Pectel SQ6M, as documented in Cosworth product information 29E-071520-5E: three Deutsch Autosport connectors, CN1 AS216-26PN (26 contacts), CN2 AS216-35PN (55 contacts, pin 46 unused) and CN3 AS216-26PA (26 contacts). Contact letters are case-sensitive (a, b and c are distinct from A, B and C). The drawings are pin indexes in alphabetical or numerical order; the circular insert layout of each connector is not reproduced. The CN1 driver ratings are worded as clipping voltages (IGBT 450 V, injector 45 V) and differ from the CN3 wording; both are reproduced as published.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
CN1 - AS2-16-26PN (mating AS6-16-26SN)
Connector reference: AS216-26PN
View: Pin index only: the circular Deutsch Autosport insert layout is not reproduced; see the manufacturer drawing for contact positions.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Injector output INJ3 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ5 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ7 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ9 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Ignition coil output IGN6 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| Ignition coil output IGN5 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| Ignition coil output IGN4 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| Ignition coil output IGN3 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| Ignition coil output IGN2 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| Ignition coil output IGN1 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
IGBT clipped to 450 V; 20 A peak. | |
| ECU battery positive (VBAT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
10 A continuous. | |
| ECU battery positive (VBAT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
10 A continuous. | |
| PWM output PWM5 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver, 10 A peak; 10 kohm pull-up and recirculation diode to VBAT. | |
| PWM output PWM3 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver, 10 A peak; 10 kohm pull-up and recirculation diode to VBAT. | |
| Injector output INJ4 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| PWM output PWM4 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver, 10 A peak; 10 kohm pull-up and recirculation diode to VBAT. | |
| Injector output INJ6 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ8 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ10 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| Injector output INJ1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver clipped to 45 V; 5 A peak, 2.5 A hold. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
10 A continuous; must be engine ground. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
10 A continuous; must be engine ground. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
10 A continuous; must be engine ground. | |
| PWM output PWM1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver, 10 A peak; 10 kohm pull-up and recirculation diode to VBAT. | |
| PWM output PWM2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Low-side driver, 10 A peak; 10 kohm pull-up and recirculation diode to VBAT. |
CN2 - AS2-16-35PN (mating AS6-16-35SN), 55 contacts
Connector reference: AS216-35PN
View: Pin index only: the circular Deutsch Autosport insert layout is not reproduced; see the manufacturer drawing for contact positions.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Analogue ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| Analogue input AIN4 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Analogue input AIN8 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Thermocouple 2 positive (TC2 POS) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Lambda 2 sensor voltage (LAMV2) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Analogue input AIN2 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Analogue input AIN6 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Analogue input AIN10 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 240 ohm. | |
| Analogue input AIN12 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 240 ohm. | |
| Lambda 2 current pump (LAMI2) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Thermocouple 1 positive (TC1 POS) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Lambda 1 sensor voltage (LAMV1) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Thermocouple negative (TC NEG) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Ethernet RX- (ETHER RXNEG) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
PC communications. | |
| Programmable sensor supply output 2 (5 V / 12 V) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V at 50 mA or 12 V at 1 A. | |
| Programmable sensor supply output 2 (5 V / 12 V) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V at 50 mA or 12 V at 1 A. | |
| Lambda 1 current pump (LAMI1) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Analogue input AIN7 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Analogue input AIN5 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Analogue input AIN1 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Ethernet TX+ (ETHER TXPOS) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
PC communications. | |
| Ethernet RX+ (ETHER RXPOS) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
PC communications. | |
| Analogue input AIN11 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 240 ohm. | |
| Analogue input AIN9 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 240 ohm. | |
| Crank/cam ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| CAN2 low Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Terminated. | |
| Analogue input AIN3 (12-bit) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-ups 3 kohm and 33 kohm. | |
| Ethernet TX- (ETHER TXNEG) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
PC communications. | |
| RS-232 TX Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Digital ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| Crank input CRANK2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| CAN2 high Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Terminated. | |
| Programmable sensor supply output 1 (5 V / 12 V) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V at 50 mA or 12 V at 1 A. | |
| Digital ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| Digital input DIN9 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| RS-232 RX Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Analogue ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| Knock sensor input DET2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Knock sensor input DET1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Crank input CRANK1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Cam input Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
||
| Digital input DIN7 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Communications ground (protected) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
1 A continuous. | |
| Digital input DIN6 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| CAN1 low Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Terminated. | |
| Unused Cavity: Unused |
Confirmed Cosworth product information 29E-071520-5E |
||
| Digital input DIN5 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Digital input DIN8 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Digital input DIN1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Digital input DIN3 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Digital input DIN10 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| CAN1 high Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Terminated. | |
| Digital input DIN2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Digital input DIN4 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Software pull-up 3 kohm. | |
| Programmable sensor supply output 1 (5 V / 12 V) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V at 50 mA or 12 V at 1 A. |
CN3 - AS2-16-26PA (mating AS6-16-26SA)
Connector reference: AS216-26PA
View: Pin index only: the circular Deutsch Autosport insert layout is not reproduced; see the manufacturer drawing for contact positions.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| ECU battery positive (VBAT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A continuous. | |
| ECU battery positive (VBAT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A continuous. | |
| Ignition coil output IGN7 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
400 V, 20 A peak. | |
| Ignition coil output IGN8 (IGBT) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
400 V, 20 A peak. | |
| DC motor driver HB3B Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A peak. | |
| DC motor driver HB3A Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A peak. | |
| CAN3 low Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
No termination. | |
| CAN3 high Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
No termination. | |
| Logic-level (TTL) ignition output IGNT7 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT5 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT3 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT1 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT2 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Full bridge HB1A Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Two 5 A full bridges or one stepper motor; 20 V, 5 A peak. | |
| Full bridge HB1B Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Two 5 A full bridges or one stepper motor; 20 V, 5 A peak. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A continuous; must be engine ground. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A continuous; must be engine ground. | |
| ECU battery negative (ECU GND) Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A continuous; must be engine ground. | |
| Injector output INJ11 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
100 V, 5 A peak, 2.5 A hold. | |
| Injector output INJ12 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
100 V, 5 A peak, 2.5 A hold. | |
| Logic-level (TTL) ignition output IGNT8 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT6 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Logic-level (TTL) ignition output IGNT4 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
5 V, 20 mA continuous. | |
| Full bridge HB2A Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Two 5 A full bridges or one stepper motor; 20 V, 5 A peak. | |
| Full bridge HB2B Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
Two 5 A full bridges or one stepper motor; 20 V, 5 A peak. | |
| PWM output PWM6 Cavity: Populated |
Confirmed Cosworth product information 29E-071520-5E |
20 V, 10 A peak; 10 kohm pull-up to VBAT. |