Converting a carburetted engine to electronic fuel injection requires more than changing the air and fuel metering hardware. The controller needs compatible engine signals, electrical power and a suitable fuel supply; the selected calibration must suit the actual engine. A conversion can use a throttle-body system, port injection equipment, or a complete injected engine and its controls.
Choose the architecture
A throttle-body injection kit places injectors at the throttle body and can reuse a compatible manifold. A port-injection conversion uses injectors at the intake ports and needs suitable mounting, rails and a manifold or correctly engineered modifications. Donor factory components may fit a related engine, but physical fit does not establish calibration or accessory compatibility. Holley's conversion overview describes throttle-body and port alternatives.
Confirm the intended fuel, engine displacement, camshaft, induction, ignition and power range against the chosen system. Check what the kit actually includes. For example, Edelbrock's Pro-Flo 4 FAQ lists a separate EFI fuel system and ignition coil among the items needed for that product; this is not an inventory for other kits.
Distribution and transient response
With throttle-body injection, fuel enters a shared intake upstream of the runners, so the manifold must distribute both fuel and air. Holley notes that distribution differences can remain in this arrangement. A port system meters fuel at each intake port, but unequal airflow, injector differences and spray placement can still affect individual cylinders. Holley: carburettor-to-EFI approaches. A single collector oxygen reading is useful but cannot establish equal mixture in every cylinder; see mixture measurement.
On a throttle opening, the air supply and the fuel reaching a cylinder do not necessarily change together. Fuel film on intake surfaces, manifold pressure response and injection timing can all affect the transition. Haltech's fuel-film description explains one controller's model; its settings are not transferable to every EFI kit. Establish a sound warm steady-state calibration and correct sensor readings before adjusting transient fuel, then compare repeatable throttle changes with time-aligned logs. Investigate mechanical, sensor or ignition faults as well as the enrichment setting. See the standalone fuel tuning guide.
Fuel system and electrical supply
Use the system manufacturer's specified pressure, flow and plumbing arrangement. An existing low-pressure carburettor pump and hose are not automatically suitable for EFI. Determine whether the selected design uses a return line, a tank-mounted regulator or another supported arrangement, and choose lines, fittings, filter, pump and tank pickup for the fuel and service pressure. Check delivered pressure and capacity under appropriate conditions. See fuel system upgrades.
Follow the controller's fuse, relay, power and grounding instructions. Its fuel pump control and shutdown strategy must be appropriate for the installation. Route wiring and hoses away from sharp edges, exhaust heat and moving components, and inspect for leaks before the first start.
Ignition and sensors
Determine whether the EFI controller only receives an engine-speed signal or also commands ignition timing. If it controls ignition, confirm the distributor or crank/cam trigger, ignition module and coil are compatible, and verify commanded against actual timing using the manufacturer's procedure. Avoid overlapping timing controls whose combined effect is unknown. Edelbrock cautions that a separate device altering timing can conflict with its controller's timing command.
Install the required coolant, air and oxygen sensors as specified for the kit. Exhaust leaks can distort oxygen feedback; Holley identifies exhaust integrity as a prerequisite for feedback-based tuning in its conversion guidance. Sensor placement and wiring are product-specific. Confirm throttle linkage and return, transmission kickdown where applicable, air cleaner and bonnet clearance before operation.
Setup and validation
Start with a mechanically sound engine, correctly functioning ignition and no known vacuum leaks. Holley's Sniper 2 instructions make these baseline checks for that installation. Enter the actual engine and injector details, use a suitable base calibration, and check fuel pressure, leaks and sensor readings before starting.
Self-learning functions have defined conditions and limits; they cannot repair mechanical faults or guarantee safe ignition, fuel supply and mixture at every operating point. Check cold and hot starting, idle, transient response and operation under representative load with suitable instruments and expertise. Record the calibration and installation details. For broader vehicle integration see planning an EFI engine swap, and for calibration checks see the standalone fuel tuning guide.