Scope
The Bosch Motronic M5.2.1 engine control module fitted to V8 Land Rover Discovery Series II and Range Rover P38 vehicles (from the 1999 model year) uses five interlocking black connectors: C0634 (9-way), C0635 (24-way), C0636 (52-way), C0637 (40-way) and C0638 (9-way), 134 positions in total. Land Rover's own engine management description lists the wire colour, function and signal range for each used position. The connectors must be fitted in numerical order and removed in reverse, because they interlock.
Connector summary
- C0634 (connector 1): main power supply and earth connections, ignition sense, switched relay positive.
- C0635 (connector 2): heated oxygen sensor signals, heaters and earths, fuel pump relay, main relay output, thermostat monitoring thermistor, DMTL pump motor.
- C0636 (connector 3): injector drivers, air flow, throttle, coolant and air temperature, crankshaft, camshaft and knock sensor signals, idle speed actuator, purge, canister vent and secondary air control.
- C0637 (connector 4): K-line diagnostics, CAN high and low, immobiliser serial link, road speed, engine speed, MIL, fuel level, tank pressure and air conditioning signals.
- C0638 (connector 5): ignition drivers for cylinder pairs 2/3, 1/6, 4/7 and 5/8, and ignition coil ground.
Evidence and limits
The pin functions come from an OEM description (manufacturer service text, read from a forum-hosted copy), so used positions are marked confirmed for this application only. Positions with no entry in the table are shown as unknown rather than assumed unused. In the source table the knock sensor earth at C0636 pin 48 is printed as bank B, the same label as pin 35; it is likely a bank A earth but this is not stated. The source does not show the connector faces or the viewing side, so the diagrams are pin-index drawings only. Other M5.2.1 applications (for example BMW M62 V8 cars) are not covered by this source.
Diagrams redrawn by Tuning Wiki from the Land Rover description.
Hub page: Bosch M5.2.1.
Sources
- Bosch 5.2.1 Engine Management System, Land Rover engine management description (PDF copy hosted on landroverforums.com), "Connector Pinouts" section. Accessed 19 November 2026.
Connector pinout
Land Rover Discovery Series II and Range Rover P38 V8 (from mid/late 1999 model year) with Bosch Motronic M5.2.1, as described in Land Rover's ECM description. Five black connectors, 134 positions. Pin functions from the OEM description (forum-hosted copy); other M5.2.1 applications (for example BMW) are not covered by this source. The face layout of the connectors is not shown in the source; the diagrams are pin-index drawings.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
C0634 (9-way, black)
View: Pin index; connector face layout and viewing side not shown in source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Ignition sense (position II) [12 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Chassis earth [0 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Fuel injectors earth [0 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Power stage earth [0 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Permanent battery supply [12 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Switched relay positive [0-12 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown |
C0635 (24-way, black)
View: Pin index; connector face layout and viewing side not shown in source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| HO2S heater, bank B downstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Thermostat monitoring thermistor ground [0 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| HO2S heater, bank A downstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S earth, bank B downstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S earth, bank A upstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S earth, bank B upstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S earth, bank A downstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| HO2S heater, bank B upstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S signal, bank B downstream [0-1 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S signal, bank A upstream [0-1 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S signal, bank B upstream [0-1 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S signal, bank A downstream [0-1 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Fuel pump relay [PWM] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| HO2S heater, bank A upstream Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Thermostat monitoring thermistor signal [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Main relay output [earth] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| DMTL pump motor Cavity: Populated |
Confirmed Land Rover ECM description |
C0636 (52-way, black)
View: Pin index; connector face layout and viewing side not shown in source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Injector #2 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Injector #5 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Purge valve driver [PWM] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| SAI valve solenoid Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Fuel tank pressure sensor earth Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Air flow meter 5 V supply Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Air flow meter earth Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Throttle potentiometer 5 V supply Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Injector #7 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Injector #6 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| SAI pump relay Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Camshaft sensor earth Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Low range switch (manual only) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Camshaft sensor input signal Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Coolant sensor earth Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Coolant temperature signal input [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Air flow meter signal input [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Throttle position sensor signal [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Throttle position sensor ground Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Injector #3 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Injector #8 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Hill descent control [PWM] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Canister vent solenoid (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| A/C condenser fan drive Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Crankshaft sensor signal Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Air temperature signal [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Knock sensor bank B earth Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Knock sensor bank B input Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Injector #4 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Injector #1 driver (switched to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Idle speed actuator open Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Idle speed actuator close Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Coolant temperature output Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Crankshaft sensor shield ground Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Crankshaft sensor ground reference Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Knock sensor earth (printed as bank B in source) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Knock sensor bank A input Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown |
C0637 (40-way, black)
View: Pin index; connector face layout and viewing side not shown in source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Transfer box low range switch Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Low fuel signal Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Fuel tank pressure sensor Vref [5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Analogue fuel level [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Fuel tank pressure signal [0-5 V] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| A/C request input Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Engine speed output Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| MIL output (on = earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Road speed signal [PWM] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| A/C compressor grant switch (to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Diagnostic K-line serial communication Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Immobiliser serial W-link Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Rough road signal [PWM] Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| CAN high Cavity: Populated |
Confirmed Land Rover ECM description |
||
| CAN low Cavity: Populated |
Confirmed Land Rover ECM description |
||
| A/C stand-by signal Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown |
C0638 (9-way, black)
View: Pin index; connector face layout and viewing side not shown in source
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Unknown function Cavity: Unknown |
Unknown | ||
| Ignition driver, cylinders 2 and 3 (switch to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown | ||
| Unknown function Cavity: Unknown |
Unknown | ||
| Ignition coil ground Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Ignition driver, cylinders 1 and 6 (switch to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Ignition driver, cylinders 4 and 7 (switch to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Ignition driver, cylinders 5 and 8 (switch to earth) Cavity: Populated |
Confirmed Land Rover ECM description |
||
| Unknown function Cavity: Unknown |
Unknown |