On the Saab 9-3 (9440) with the Z19DTH 1.9-litre diesel, the Bosch EDC16C39 engine control module (Saab component 595) is connected through two harness connectors, A and B. This page lists every control-module pin that appears in the Saab WIS wiring diagram for the 2008 model year Z19DTH (diagram F8E20A, parts 1–4), together with the component and component pin it is wired to. The wiring diagram is manufacturer service information; 72 pins are shown (37 on A, 35 on B). Pins not drawn there are not established.
Connector A
Connector A carries the engine-side functions: the four injectors (two pins each: cylinder 1 A16/A47, cylinder 2 A2/A31, cylinder 3 A1/A46, cylinder 4 A17/A33), the high-pressure pump fuel pressure control valve (A19/A49), the fuel rail pressure sensor (A8, A43, A28), crankshaft and camshaft position sensors, the mass air flow unit, the intake air (charge pressure and temperature) sensor, coolant temperature, the oil level and oil pressure switches, the swirl and throttle actuators and the EGR valve (A60).
Connector B
Connector B carries the supplies and grounds (B1 and B5 from main relay terminal 87, B28 from +15 fuse 4, grounds B2, B4 and B6), main relay control (B72), the six-wire accelerator pedal sensor, brake and clutch switches, the ignition switch module, the engine warning lamp, the P-bus link to the column integration module (B83/B84), glow plug control module signals (B52, B93), the charge air solenoid valve (B7), exhaust temperature and pressure sensors and the oxygen sensor.
Variant notes
The diagram covers both particulate-filter and non-filter cars: the oxygen sensor 136 (B51, B64, B65, B86, B87) is marked for cars without DPF, and the rear exhaust temperature sensor 602R and exhaust pressure sensor 744 are marked for DPF cars. Saab publishes separate EDC16 diagrams for the Z19DH (titled DT) and Z19DTR, and other EDC16C39 applications (Fiat, Alfa Romeo, Opel, Hyundai and others) use their own harnesses; this assignment should not be transferred to them without the matching diagram.
Diagram
The Saab diagram is a circuit schematic and does not show the physical connector face, so the interactive view on this page is a numbered pin index, not a drawing of the housing. Index redrawn by Tuning Wiki from the Saab WIS EDC16 wiring diagrams.
Not established
The total cavity count and face layout of connectors A and B, the pins not drawn in the Z19DTH diagram, and the signal role of each wire beyond the component pin it serves (for example which P-bus wire is high or low).
Sources
- Engine management system EDC16 DTH, part 1(4), part 2(4), part 3(4) and part 4(4). Saab Workshop Information System, 9-3 (9440) 2008, diagram F8E20A (sheets dated 2007), republished by SaabWISOnline. Accessed 19 November 2026.
- EDC16 brief description, 9-3 (9440) 2008. Saab Workshop Information System; names Bosch EDC16C39 for Z19DH and Z19DTH. Accessed 19 November 2026.
Connector pinout
Bosch EDC16C39 (Saab EDC16 control module 595) on the Saab 9-3 (9440) MY2008 with the Z19DTH engine, taken from the Saab WIS wiring diagram (manufacturer service information). Only pins drawn in that diagram are listed; other pins are not established. Separate Saab diagrams exist for Z19DH (DT) and Z19DTR, and other EDC16C39 applications (Fiat, Alfa Romeo, Opel, Hyundai and others) must not be assumed to share this assignment.
View orientation is stated beside each photograph. Unknown functions remain in the pin index.
Connector A (control module 595)
View: Numbered index of the pins that appear in the Saab wiring diagrams; not a drawing of the connector face, which the source does not show.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Injector, cylinder 3 (206c) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 2 (206b) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Swirl throttle actuator (403), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Crankshaft position sensor (345), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Drawn connected to the screen of the crankshaft sensor cable. | |
| Fuel rail pressure sensor (653), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Camshaft position sensor (555), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Crankshaft position sensor (345), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Intake air sensor (688), pin C Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
688 combines charge-air pressure sensor 603 and intake air temperature sensor 407. | |
| Injector, cylinder 1 (206a) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 4 (206d) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Fuel pressure control valve, high-pressure pump (652b) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Camshaft position sensor (555), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Engine oil level switch (243), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Intake air sensor (688), pin A Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
688 combines charge-air pressure sensor 603 and intake air temperature sensor 407. | |
| Crankshaft position sensor (345), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Fuel rail pressure sensor (653), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 2 (206b) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 4 (206d) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Swirl throttle actuator (403), pin 5 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Mass air flow sensor unit (686), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
686 combines the mass air flow sensor (205) and its temperature sensor (772). | |
| Throttle body actuator (604), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Intake air sensor (688), pin D Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
688 combines charge-air pressure sensor 603 and intake air temperature sensor 407. | |
| Coolant temperature sensor (202), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Mass air flow sensor unit (686), pin 4 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
686 combines the mass air flow sensor (205) and its temperature sensor (772). | |
| Fuel rail pressure sensor (653), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Mass air flow sensor unit (686), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
686 combines the mass air flow sensor (205) and its temperature sensor (772). | |
| Swirl throttle actuator (403), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 3 (206c) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Injector, cylinder 1 (206a) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Fuel pressure control valve, high-pressure pump (652b) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Camshaft position sensor (555), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Throttle body actuator (604), pin 4 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Intake air sensor (688), pin B Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
688 combines charge-air pressure sensor 603 and intake air temperature sensor 407. | |
| Engine oil pressure switch (44) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Coolant temperature sensor (202), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Throttle body actuator (604), pin 6 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| EGR solenoid valve (606), pin 5 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Connector B (control module 595)
View: Numbered index of the pins that appear in the Saab wiring diagrams; not a drawing of the connector face, which the source does not show.
Select a pin in a photograph or the index to highlight it.
| Pin | Function / cavity | Confidence / source | Notes |
|---|---|---|---|
| Supply from main relay (229) terminal 87 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Ground (to G2) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Ground (to G2) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Supply from main relay (229) terminal 87 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Ground (to G2) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Charge air solenoid valve (179a), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Accelerator position sensor (379), pin 5 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Accelerator position sensor (379), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Brake light switch (29), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| +15 (ignition) supply, fuse 4 in underhood electrical centre (342) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Accelerator position sensor (379), pin 4 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Accelerator position sensor (379), pin 6 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Rear exhaust temperature sensor (602R), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars with a diesel particulate filter (DPF). | |
| Rear exhaust temperature sensor (602R), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars with a diesel particulate filter (DPF). | |
| Front exhaust temperature sensor (602F), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Front exhaust temperature sensor (602F), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Exhaust pressure sensor (744), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars with a diesel particulate filter (DPF). | |
| Exhaust pressure sensor (744), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars with a diesel particulate filter (DPF). | |
| Ignition switch module (20), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Exhaust pressure sensor (744), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars with a diesel particulate filter (DPF). | |
| Accelerator position sensor (379), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Accelerator position sensor (379), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Main instrument unit (540), engine warning lamp Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Oxygen sensor (136), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars without a diesel particulate filter (136 marked NO DPF). | |
| Glow plug control module (596), pin 8 (DI) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Oxygen sensor (136), pin 6 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars without a diesel particulate filter (136 marked NO DPF). | |
| Oxygen sensor (136), pin 1 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars without a diesel particulate filter (136 marked NO DPF). | |
| Main relay (229) terminal 85 (relay control) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Clutch switch, cruise control (133), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| Brake switch, cruise control (134), pin 3 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
||
| P-bus Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
P-bus link to the column integration module (703); the diagram does not identify which wire is which line. | |
| P-bus Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
P-bus link to the column integration module (703); the diagram does not identify which wire is which line. | |
| Oxygen sensor (136), pin 2 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars without a diesel particulate filter (136 marked NO DPF). | |
| Oxygen sensor (136), pin 5 Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |
Shown for cars without a diesel particulate filter (136 marked NO DPF). | |
| Glow plug control module (596), pin 7 (ST) Cavity: Populated |
Confirmed Saab WIS 9-3 2008 Z19DTH F8E20A |