Tuning Wiki
Browse BMW

BMW's E46 automatic-transmission training covers both the GM-built A5S 360R, identified in that document as 5L40-E, and the ZF-built A5S 325Z / 5HP19. Both are five-speed torque-converter automatics but their hardware and diagnostics differ. Identify the exact gearbox, VIN, identification plate, controller software and production variant before using the examples here. These are distinct from the E46 M3's SMG II automated manual.

Source: supplied BMW training file 12 Automatic Transmission Internet.pdf, PDF pp. 3–32 for A5S 360R and pp. 33–54 for A5S 325Z. A BMW training reproduction may require a browser security check. Applicability examples in an old training document are not a complete fitment catalogue.

Identify the hardware first

The training describes GS 20 electronic control for its A5S 360R example, with an electrohydraulic valve body. It identifies a dedicated engine-controller to transmission-controller CAN link for the documented early E46 arrangement. Its A5S 325Z material describes a ZF transmission with a different converter and shift-control arrangement. Do not infer a controller, valve body, oil or fault definition from the E46 badge alone. BMW training PDF pp. 3–4, 8, 21 and 33–34.

A5S 360R: signals, lockup and adaptation

In the documented GM example, input/turbine and output speed sensors are inductive; the controller compares their signals with engine speed for ratio and shift-slip monitoring. It can substitute an oil-temperature value based on engine temperature when the oil-temperature signal is impaired, while recording a fault. A plausible temperature displayed on a scan tool can therefore be a substitute rather than an actual measurement. Check relevant faults, wiring and live-data status before judging the sensor. BMW training PDF p. 19.

The 360R training describes variable converter-clutch slip in third, fourth and fifth gears and PWM control of the converter and main-pressure regulators. A modest measured speed difference must be interpreted alongside commanded converter state, temperature, load and channel definition; it does not alone prove a failed clutch. BMW training PDF pp. 4 and 20. See torque-converter clutch diagnosis.

BMW distinguishes driving-program adaptation from the GM example's hydraulic-pressure adaptation. The latter compares target and actual shift slip and adjusts regulator control. The training warns that clearing the pressure adaptations can temporarily worsen shift quality until the transmission relearns. Do not reset values as the first diagnostic step or treat a reset as a repair for low oil, wiring or mechanical damage. BMW training PDF p. 25.

Failsafe is conditional

For this A5S 360R training example, a detected fault that invokes its emergency programme is described as selecting fifth in drive ranges, while a power-down of the control module is described as selecting fourth. In both examples the converter lockup is unavailable. These are two distinct failure paths, not universal fixed limp gears for every GM or ZF automatic. Record whether the fault is present, the controller is powered and communicative, and the actual ratio. BMW training PDF p. 26.

Evidence-led diagnosis and service

  1. Record VIN, transmission and controller identifiers, prior repair and fluid history, warning and temperature/load conditions. Save transmission, engine and other relevant module faults before clearing them.
  2. Compare engine, turbine and output speeds, commanded gear, actual ratio and converter command as available. An implausible speed signal or missing engine data can affect both ratio judgement and pressure adaptation; test the signal and its circuit before replacing a valve body.
  3. For a harsh or delayed shift, assess voltage, fluid condition and level using the exact current procedure, faults, temperature and shift timing. BMW's separate Electronic Transmissions: Transmission Service resource, PDF pp. 4–5, recommends model-specific test plans and temperature-aware level checking.
  4. Use the correct approved fluid and applicable current repair information. The historic training describes production fluid changes; it is not a current blanket fluid recommendation for all 360R variants. ZF: 5HP and 6HP oil-service instructions.

The separate A5S 325Z section describes a Hall-effect turbine-speed sensor and its own adaptation and programming process (BMW training PDF pp. 48–50). Do not copy the 360R's inductive-sensor assumptions, emergency behaviour or adaptation instructions to it. Related: gearbox catalogue and ZF transmission tuning and swap diagnosis.